GRS 003-615 User manual
PAGE 1 of 2 LIT-141
GRS Low Profile Ball Vise
For Engraving And Jewelry Making #003-615
BALL SWIVEL
TENSION SCREW
Maintenance
Based on usage, open jaws fully and clean any dirt
and metal pieces from the threads. After cleaning,
apply a small amount of light oil to the threads.
Jaw Thread Replacement
Over tightening the jaws will cause wear and damage
to the threads. If jaws become loose, replace with kit
#003-627. Remove jaws by opening wide until they
come off the jaw screw. The thread pin (A) is located
on the under side of each jaw. Before removing
pins locate the left hand pin, marked “L”. Replace it
with the same. Apply a small amount of grease to the
O-rings before installing them. Start the jaws threads
at the same time when replacing them. Hold each
jaw in position (Fig. 1) and turn the jaw screw. An
extra pair of hands makes this easier, or place a large
rubber band over the jaws.
Optional Turntable Base For Microscope Work
To use the turntable base, lock the vise by tightening
the swivel tension screw until the ball will not turn.
The turntable now becomes your rotation, allowing
you to adjust the work’s center of rotation into the
eld of view of the microscope. Align the center of the
turntable with the center of the microscope (Fig. 2).
Change working views by repositioning the vise.
Fig. 1
“L” For Left
Hand Thread
(A) Jaw Thread Pin
one located in each jaw
Jaw Thread
Jaw
Fig. 2
POSITION CENTER OF TURNTABLE WITH
THE CENTER OF THE MICROSCOPE VIEW
MICROSCOPE
POSITION VISE
SO THAT THE
WORK IS IN
THE CENTER
OF THE
TURNTABLE
ROTATION
CENTER LINE
OPTIONAL
TURNTABLE
#003-616
O-Rings
900 Overlander Road
P.O. Box 1153
Emporia, KS 66801 USA
Toll-Free: 1-800-835-3519
Phone: 620-343-1084
Fax: 620-343-9640
E-mail: [email protected]
www.grstools.com
PAGE 2 of 2 LIT-141
GRS Low Prole Ball Vise
Complete Assembly #003-615
PART # DESCRIPTION
1 003-220 Block Base
2 003-219 Block Crown
3 003-221 Post
4 003-009 Jaw - Right Hand
5 003-008 Jaw - Left Hand
6 003-064 Pin - Left Hand
7 003-065 Pin - Right Hand
8 003-007 Screw Post
9 003-067 1/2 - 13 x 1/2 SSS Flt Pt HF Dog
10 002-127 O-Ring - 0.625" x 0.75" x 0.062"
11 022-181 Bearing 6203ZZ
12 002-214 Washer - 0.312" x 0.859" x 0.125"
13 002-112 5/16-8 x 3/4" HHB Z/P
14 003-212 Spring
15 022-180 Washer
16 003-222 Spacer
17 002-088 Bearing 3" x 3.75" x 0.078"
18 002-089 Bearing 3" x 3.75" x 0.031" Race
19 002-213 Bearing 3" x 3.75" x 0.062" Race
20 003-223 Lock Pin
003-506 Tire Assembly ( 21 & 22)
21 002-090 Tire
22 002-209 Fastener - Push-In
23 002-091 Wrench - 1/4" T-Handle Hex
24 003-661 1/4" Hex Drive Knob
25 003-015 Jaw Pin - 1/4"
26 003-016 Jaw Pin - 3/8"
27 003-507 Pin Plate - 2 pin
28 003-508 Pin Plate - 1 pin
Replacement Thread Pin Kit
#003-627 (Not Shown). Includes Jaw Screw, Left and
Right Thread Pins, O-Rings, and Tube of Grease.
Optional Turntable For Microscope Work
#003-616 (Not Shown).
1
7
10
21
22
25
26
27
28
9
14
20
6
3
2
19 - RACE
(thick shim)
17 - BEARING
18 - RACE
(thin shim)
15
11
16
11
12
13
5
4
23
8
24
Other GRS Lathe manuals
