Growatt 10000HYP User manual

GROWATT NEW ENERGY TECHNOLOGY Co.,LTD

+ 86 755 2747 1900

+ 86 755 2747 2131

info@ginverter.com

www.ginverter.com

No.28 Guangming Road, Shiyan, Baoan District,

Shenzhen, P.R. China

Growatt 10000HYP

Parallel Installation Guide

1 Introduction

This inverter can be used in parallel with maximum 3 units. The supported maximum

output power is 30KW/30KVA.

When installing multiple units, please follow below chart.

NOTE:

of approx. 20 cm to the side and approx. 50 cm above and below the unit. Be sure to

install each unit in the same level.

For proper air circulation to dissipate heat, it’s necessary to allow a clearance

WARNING:

be voltage difference between inverter and battery to cause parallel inverters not

working.

Be sure the length of all battery cables is the same. Otherwise, there will

Recommended battery cable and terminal size for each inverter:

2 Parallel cable

3 Overview

You will find the following items in the package:

Parallel communication cable Current sharing cable

1.Parallel communication port

2.Current sharing port

4 Mounting the Unit

5 Wiring Connection

The cable size of each inverter is shown as below:

Ring terminal:

Model Wire Size

Ring Terminal

Torque valueCable mm2 Dimensions

D (mm) L (mm)

Growatt 10000HYP 3/0 85 8.4 54.2 7~12 Nm

3 4

Recommended AC input and output cable size for each inverter:

You need to connect the cables of each inverter together. Take the battery cables for

example. You need to use a connector or bus-bar as a joint to connect the battery

cables together, and then connect to the battery terminal. The cable size used from

joint to battery should be X times cable size in the tables above. “X” indicates the

number of inverters connected in parallel.

Regarding cable size of AC input and output, please also follow the same principle.

CAUTION!!

can be securely disconnected during maintenance and fully protected from

overcurrent of battery.

Please install a breaker at the battery side. This will ensure the inverter

Model AWG no. Conductor cross

-section Torque

Growatt 10000HYP 10~8 AWG 5.5~10 mm2 1.4~1.6Nm

Recommended breaker specification of battery for each inverter:

*If you want to use only one breaker at the battery side for the whole system, the

rating of the breaker should be X times current of one unit. “X” indicates the number

of inverters connected in parallel.

Model One unit*

Growatt 10000HYP 300A/60VDC

Recommended battery capacity

CAUTION!

to choose the suitable battery. The wrong charging parameters will reduce the

battery lifecycle sharply.

Please follow the battery charging current and voltage from battery spec

Inverter parallel numbers 2 3

Battery Capacity 800AH 1200AH

Approximate back-up time table

PV Connection

Please refer to user manual of single unit for PV Connection.

CAUTION: Each inverter should connect to PV modules separately.

Load (W)

10,000

20,000

5,000

15,000

25,000

30,000

Backup Time @ 48Vdc

800Ah (min)

112

240

Backup Time @ 48Vdc

1200Ah (min)

168

360

6 Inverters Configuration

Two inverters in parallel:

Power Connection

Communication Connection

Three inverters in parallel:

Power Connection

7 Setting and LCD Display

Setting Program:

The parallel function setting is only available by SolarPower. Please install SolarPower

in your PC first.

For setting, you can set the inverter one by one through RS232 or USB port.

But we suggest to use SNMP or Modbus card to combine the system as a centralized

monitoring system. Then, you can use “SYNC” function to set all the inverters at the

same time. If using SNMP or Modbus card to set up program, the bundled software is

SolarPower Pro.

Use SNMP card to synchronize the parameters:

Each inverter should be installed one SNMP card. Make sure all of the SNMP cards are

connected to the router as a LAN.

Use Modbus card to synchronize the parameters:

Each inverter should be installed one Modbus card. Make sure all of the Modbus

cards are connected to each other and one of the Modbus cards is connected to the

computer by RS-485/RS232 converter.

Launch SolarPowerPro in computer and select Device Control >> Parameter Setting

>> Parallel output. Two options: Enable or Disable.

If you want to use parallel function, please choose “Enable” and press “ ”

button. Then, “ ” button will be shown is the screen. Please be sure to click

“ ” button before clicking “ ” button.

There is a “Sync” button in each parameter setting. When “Sync” is clicked and

“Apply” is pressed, this new setting will be applied to all inverters. If not, this setting

is only effected in current inverter you choose.

Note: Without centralized monitoring system, “Sync” function is not effective. Then,

you have to set up the inverter one by one through serial communication port.

Parallel for output: Enable

Parallel for output: Disable

910

Fault code display:

Step 1: Check the following requirements before commissioning:

 Correct wire connection.

 Ensure all breakers in Line wires of load side are open and each Neutral wire of

each unit is connected together.

Step 2: Turn on each unit and set “enable parallel for output” on SolarPower or

SolarPower Pro. And then, shut down all units.

Step 3: Turn on each unit.

NOTE: Master and slave units are randomly defined. Warning 02 is AC GRID voltage

low.

Step 4: Switch on all AC breakers of Line wires in AC input. It’s better to have all

inverters connect to utility at the same time. If not, it will display fault 82 in

following-order inverters. However, these inverters will automatically restart. If

detecting AC connection, they will work normally.

Fault Code Fault Event Icon on

Over current on Neutral wire

Power feedback protection

Relay board driver loss

Relay board communication loss

Firmware version inconsistent

Current sharing fault

CAN fault

Host loss

Synchronization loss

LCD display in Master unit LCD display in Slave unit

Step 5: If there is no more fault alarm, the parallel system is completely installed.

Step 6: Please switch on all breakers of Line wires in load side. This system will start

to provide power to the load.

LCD display in Master unit LCD display in Slave unit

9 Trouble shooting

Situation

Fault Code Fault Event Description

Solution

Relay board driver loss

CAN data loss

Host data loss

Current feedback into

the inverter is detected.

1.Restart the inverter.

2.Check if L1/L2/L3/N cables are not

connected with wrong sequence in all

inverters.

3.Make sure the sharing cables are connected

in all inverters.

4.If the problem remains, please contact your

installer.

1.Check if sharing cables are connected well

and restart the inverter.

2.If the problem remains, please contact your

installer.

1.Check if communication cables are

connected well and restart the inverter.

2.If the problem remains, please contact your

installer.

1.Disconnect all of power source.

2.Only connect AC input, and press Enter key

to let it working in bypass mode.

3.Check if the problem happens again or not,

and feed back the result to your installer.

1.Update all inverter firmware to the same

version.

2.After updating, if the problem still remains,

please contact your installer.

Relay board

communication loss

The firmware version of

each inverter is not the

same.

The output current of

each inverter is

different.

Synchronization data

loss

1.Remove excessive loads.

2.Restart the inverter.

3.If the problem remains, please contact your

installer.

Over current on Neutral

wire

Table of contents

Other Growatt Inverter manuals

Growatt

Growatt MIN 2500TL-X User manual

Growatt

Growatt MIN 3000TL-XH-US User manual

Growatt

Growatt MIN 2500TL-XA User manual

Growatt

Growatt MIN 2500 TL-XE User manual

Growatt

Growatt SPF 18KT DVM-MPV User manual

Growatt

Growatt MIN 2500TL-XH User manual

Growatt

Growatt MOD TL3-XH Series User manual

Growatt

Growatt 2000-US User manual

Growatt

Growatt MID TL3-XH Series User manual

Growatt

Growatt MID TL3-XH Series User manual

Growatt

Growatt MIN 2500-6000TL-XH User manual

Growatt

Growatt SPF 4000T DVM-MPV User manual

Growatt

Growatt SPF 3500 ES User manual

Growatt

Growatt MIN 2500TL-X User manual

Growatt

Growatt MAX 100KTL3-X LV User manual

Growatt

Growatt 2KVA User manual

Growatt

Growatt SPF 2000TL User manual

Growatt

Growatt MOD 3000TL3-XH User manual

Growatt

Growatt SPH TL BL-UP Series User manual

Growatt

Growatt MID 11-30KTL3-XH User manual

Growatt

Growatt 2500MTL User manual

Growatt

Growatt MID 1 7 KTL3-X1 User manual

Growatt

Growatt MAX Series User manual

Growatt

Growatt SPA TL3 BH-UP Series User manual

Popular Inverter manuals by other brands

Fourgroup

Fourgroup Easy use and Programming Handbook

Velleman

Velleman PI300M user manual

Sungrow

Sungrow SG350HX-US user manual

WilTec

WilTec 61897 Operation manual

SMA

SMA SUNNY BOY STORAGE 2.5 Quick reference guide

Simplicity

Simplicity LANDLORD 316 product manual

Santak

Santak SMAX 3000 user manual

ATON

ATON RA.Store-3 user manual

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ operating instructions

Tektronix

Tektronix CFG250 Operator's manual

Champion

Champion 200989 Operator's manual

Vanner

Vanner 20-500 Series owner's manual

GE GEP user manual

Astrel Group

Astrel Group Power Reducer Installation and instruction manual

MULTIQUIP

MULTIQUIP GDP-5H Operation and parts manual

GoWISE

GoWISE PS1007 user manual

Promate

Promate PM13500D ES Operator's manual

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM user manual