Grizzly H0596 User manual

Introduction

This 25,000 RPM air belt sander requires 90 PSI,

4 CFM, and 3/8" x 13" sanding belts. Four-pack

sanding belts (Model H2322) can be purchased

separately for the Model H0596.

Inventory

A. Air Belt Sander ........................................... 1

B. 3/8" x 13" Sanding Belts .............................. 2

C. Hex Wrench 3mm ...................................... 1

MODEL H0596

AIR BELT SANDER

INSTRUCTION SHEET

Figure 2. Loosening cap screw and hex nut.

Figure 1. Model H0596.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL8253 PRINTED IN TAIWAN

Adjusting Platen and Attaching Belt

To adjust the platen:

1. Using the hex wrench, loosen the cap screw

and hex nut shown in Figure 2 and turn the

platen to the desired operating angle.

3. Tighten the cap screw and hex nut loosened

in Step 1.

Figure 3. Squaring mounting surfaces.

2. Make sure the platen and housing surfaces

(Figure 3A) are seated and flush with one

another. If these mounting surfaces are not

square, remove the platen from the housing

(Figure 3B) and reseat the platen and clamp

nut.

Platen

Clamp

Nut

A B

Platen

Housing Mounting Surfaces

EYE INJURY HAZARD!

Always wear safety glasses

when using this tool to

prevent serious personal

injury.

INJURY HAZARD!

Always disconnect tool from

air to prevent unexpected

operation during service.

DUST HAZARD!

Always wear respirator when

using this tool.

Figure 4. Loosening screw on platen.

Operation

To operate the sander:

1. Plug the sander into compressed air.

2. Hold the sander and push the throttle lever

(Figure 6) to operate the sander and adjust

the speed. Turn the valve screw to set the

maximum belt speed.

Figure 7. Lubricating directly into air fitting.

Maintenance

Lubricate at the beginning of the sanding task.

Place one or two drops of pneumatic tool oil

directly into the air fitting as shown in Figure 7.

A filter/lubricator/regulator set up is not recom-

mended, as excess oil in the tool could spray onto

the workpiece.

Figure 6. Sander controls.

Throttle

Lever

To attach the sanding belt:

1. Loosen the screw on the platen (Figure

4), press the wheel inward, and tighten the

screw.

2. Install the sanding belt as shown in Figure

3. Loosen the screw shown in Figure 4 to auto-

matically tension the belt.

Figure 5. Installing sanding belt.

3. Remove pressure on the throttle lever to stop

the sander.

4. When the sanding belt loses its effective-

ness, disconnect the sander from air,

remove the belt and replace with a new one.

Valve

Screw

Run the sander for a few minutes to eject excess

oil, then wipe the tool down with a rag and begin

sanding. Oil the tool after use or storage.

If you need help with your new pneumatic tool,

call our Tech Support at: (570) 546-9663.

Also, apply one to two squirts of non-detergent

motor oil, such as SAE 20W, into the oil ball

shown in Figure 8.

Figure 8. Oil ball.

H0596 Parts Breakdown and List

























 

























 







 

 















 





REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PH0596001 MOTOR HOUSING 24 PH0596024 SPINDLE GEAR

2 PH0596002 THROTTLE VALVE 25 P608 BALL BEARING 608ZZ

3 PH0596003 THROTTLE VALVE SPRING 3.8 X 14 26 PH0596026 WOODRUFF KEY 2 X 4.2

4 PH0596004 AIR REGULATOR 27 PH0596027 SPINDLE

5 PH0596005 O-RING 7 X 1.4 28 PH0596028 CLAMP NUT M24-1.25 X 14

6 PH0596006 O-RING 12 X 2 31 PH0596031 THROTTLE VALVE BUSHING

7 PH0596007 VALVE SCREW M14-1.25 X 9.2 32 PH0596032 O-RING

8 PH0596008 THROTTLE LEVER 33 PH0596033 BELT SET

9 PH0596009 THROTTLE LEVER PIN 34 PH0596034 EXHAUST SLEEVE

10 P696 BALL BEARING 696ZZ 35 PH0596035 HOSE ADAPTER

11 PH0596011 REAR END PLATE 36 PH0596036 ADJUSTMENT BAR

12 PH0596012 BALL 37 PH0596037 COMPRESSION SPRING 10 X 37

13 PH0596013 ROTOR COLLAR 41 PSB23M CAP SCREW M4-.7 X 12

14 PH0596014 CYLINDER 42 G3855 BALL BEARING 695ZZ

15 PH0596015 ROTOR 43 PSB20M CAP SCREW M5-.8 X 14

16 PH0596016 ROTOR BLADE 44 PH0596044 BELT WHEEL

17 PH0596017 FRONT END PLATE 45 PLN01M LOCK NUT M4-.7

18 P608 BALL BEARING 608ZZ 46 PSB23M CAP SCREW M4-.7 X 12

19 PH0596019 PINION 47 PH0596047 BELT WHEEL

20 PH0596020 MOTOR CLAMP 48 PH0596048 SPACER 5MM

21 PH0596021 HOUSING LOCK RING 49 PH0596049 OIL BALL

22 PH0596022 ANGLE HEAD BUSHING 53 PH0596053 SANDING BELT 3/8" x 13"

23 P696 BALL BEARING 696ZZ 54 PAW03M HEX WRENCH 3MM

Popular Sander manuals by other brands

Oliver

Oliver 6305 owner's manual

Jet

Jet 22-44 Pro-3 Operating instructions and parts manual

Makita

Makita M9204 technical information

Makita

Makita M9204 instruction manual

Craftsman

Craftsman 351.215131 Operator's manual

Clarke

Clarke Woodworker CBS1-5B Operation & maintenance instructions

Chicago Pneumatic

Chicago Pneumatic CP9778 Operator's manual

Nitto Kohki

Nitto Kohki BB-20 instruction manual

Ferm

Ferm FEOS-135 user manual

Unior

Unior 1510 Operating instruction

stayer

stayer ls1200 operating instructions

Jet

Jet JSG-96 Operating instructions and parts manual

Parkside

Parkside PDS 290 B2 Operation and safety notes

Status

Status XPA Series Original instructions

Clarke

Clarke EZ Sand Operator's manual

Craftsman

Craftsman 113.22521 owner's manual

Craftsman

Craftsman 113.225831 owner's manual

CLAS

CLAS OP 1429 manual