Grizzly T33682 User manual
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
MODEL T33682
DRILL PRESS TRAY
INSTRUCTIONS
Introduction
***Keep for Future Reference***
The Model T33682 holds bits, chucks and other
equipment for your drill press. It easily mounts to a
drill press column up to 43⁄4" in diameter, and can
be conveniently rotated 360° during operations for
closer access.
The tray size is 113⁄8" across and has pre-drilled
mounting holes for bit sizes 1⁄16" to 1⁄2" in 32nd and
64th increments.
To reduce risk of serious
injury, read this entire
manual BEFORE using
drill press tray. Read and
understand instructions/
safety warnings provided
by manufacturer for any
machine or tool you plan to
use with this tray.
Figure 1. Model T33682.
Inventory
Contents (Figure 2) Qty
A. Tool Tray ..................................................... 1
B. Z-Bar 1⁄2" ..................................................... 1
C. Z-Bar 3⁄8" ..................................................... 1
D. Key Hose Clamps 5" .................................. 2
E. Z-Bar Adapter ............................................. 1
F. Mounting Block ........................................... 1
Figure 2. Inventory.
A B
C
D
E
F
COPYRIGHT © JULY, 2023 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 07/23) #JM22675 PRINTED IN CHINA V1.07.23
-2- Model T33682 (Mfd. Since 07/23)
Installation
Installing the Model T33682 consists of clamping
the mounting block to the drill press column, and
installing the Z-bars, adapter, and tool tray.
Figure 4. 1⁄2" Z-bar installed.
Mounting
Block
1⁄2" Z-Bar
6. Mount Z-bar adapter on 1⁄2" Z-bar
(see Figure 5).
Note: Z-bar adapter has one end drilled at 3⁄8"
and one end drilled at 1⁄2".
7. Mount 3⁄8" Z - b a r i n t o Z - b a r a d a p t e r
(see Figure 5).
8. Insert tool tray on top of 3⁄8" Z - b a r
(see Figure 5).
5. Mount 1⁄2" Z-bar into mounting block
(see Figure 4).
Figure 5. Drill press tray installed.
Tool Tray
3⁄8" Z-Bar
Z-Bar
Adapter
To install drill press tray:
1. Unscrew hose clamp key until band is free of
shroud, then repeat with second hose clamp.
2. Feed clamp bands through slots in mounting
block, then slide clamp bands underneath
drill press rack (see Figure 3).
Note: Do not position clamps over rack. They
will interfere with movement of drill press
column.
3. Position mounting block on drill press column
(see Figure 3).
Note: Position mounting block high enough
on column so it does not interfere with table
movement.
4. Insert clamp bands in shrouds and tighten
until snug (see Figure 3).
Figure 3. Mounting block attached on drill press
column.
Column
Rack
Key Hose
Clamps
(1 of 2)
Mounting
Block
Mounting
Block
Slot
(1 of 2)
Clamp
(1 of 2)
Other Grizzly Drill manuals
Grizzly
Grizzly H0625 Instruction Manual
Grizzly
Grizzly H6363 Quick start guide
Grizzly
Grizzly G0781 User manual
Grizzly
Grizzly T30943 User manual
Grizzly
Grizzly G0784 User manual
Grizzly
Grizzly G1006 User manual
Grizzly
Grizzly G0756 User manual
Grizzly
Grizzly G8593 User manual
Grizzly
Grizzly G7943 Instruction Manual
Grizzly
Grizzly G3358 User manual
Grizzly
Grizzly G0485 User manual
Grizzly
Grizzly G8600 User manual
Grizzly
Grizzly G0704 User manual
Grizzly
Grizzly G0935 User manual
Grizzly
Grizzly G7945/46 User manual
Grizzly
Grizzly H7819 User manual
Grizzly
Grizzly C1393-96 User manual
Grizzly
Grizzly G7942 Quick start guide
Grizzly
Grizzly G3358 User manual
Grizzly
Grizzly G1131 User manual
