Greenplate 300 User manual

21/06/2016
This design has been reviewed to assess the disability access provisions as stated in current
legislative Acts , Codes and Standards. This design review has been conducted by the below
signed Accredited Member under the Association of Consultants in Access Australia (ACAA).
Signed: Date:
A: 15 Castleridge Crt
Narre Warren South VIC 3805
P: (03) 9705 2149 M: 0411 201 125
DESIGN REVIEWED
ACAA MN: 175

Access%Solutions%National%P/L%
ACN:%110%131%676%%%%%ABN:%69%110%131%676%
A:%15%Castleridge%Crt%
Narre%Warren%South%VIC%3805%
P:%(03)%9705%2149%%%%%M:%0411%20%11%25%
E:%[email protected]%%%%%%%W:%www.asnpl.com.auL
JN-1613-LOA-V1-21.06.16%
Peter%Hurley%
Greenplate%P/L%
A:%Unit%2/15%Natasha%St%
Capalaba%QLD%4157%
Dear%Peter%
RE:%Accessibility%Design%Certification%–%BBQ%–%Greenplate%Equal%Access%Single%Bench%
Access%Solutions%National%Pty.%Ltd.%(ASN)%has%been%engaged%to%review%and%confirm%accessibility%as%required%
by%current%legislation%and%best%practice%relating%of%the%above%mentioned%product%by%Greenplate%P/L.%%
The%review%has%been%based%upon%a%comparison%to%the%requirements%in%Australian%Standard%AS1428.1%–%
2009%Figure%44%(A)%and%AS1428.2%Figure%20%(b).%It%is%important%to%note%that%there%are%no%specific%Australian%
Standards%for%disability%access%that%directly%apply%to%BBQ’s,%therefore%all%references%and%comparisons%to%
these%Standards%are%done%so%as%current%best%practice.%%
Therefore,%upon%reviewing%the%BBQ%–%Greenplate%Equal%Access%Single%Bench%(as%shown%in%Appendix%1%
following)%ASN%confirms%that%the%design,%in%our%professional%capacity%and%opinion,%is%accessible%to%a%wide%
range%of%community%members%inclusive%of%people%with%disability.%
ASN%grants%the%BBQ%–%Greenplate%Equal%Access%Single%Bench%(as%shown%in%Appendix%1%following)%the%status%
of:%
!"#$%"&"'()$**+##"%&+),)*+-'"."+!)/%%012314356)
The%above%status%allows%the%above%client%the%freedom%to%promote%this%product%as%accessible.%%
***NOTE***%-%Accessible%may%not%mean%compliant%to%an%Act,%Standard%or%Code%but%useable%&%accessible.%
This%certification%is%not%transferrable%to%any%other%product.%
Should%further%explanation%or%information%be%required%please%feel%free%to%contact%myself%directly.%
Kind%Regards,%
!789)#:9;;7<=)/ACAA%MN:%175)%
Director%-%Access%Solutions%National%P/L%
21 June
2016

S:\Libraries\Documents\Greenplate BBQ Info\Bench Wiring Requirements\Equal Access Single Barbecue Bench Installation Information PID.doc | Updated 14-08-2018
Greenplate ® Equal Access Single Barbecue Bench Electrical Wiring Requirements
Base size of Bench790 mm x 550 mm.
50 mm turn in for fixing of bench to the concrete slab.
4 x M10 Dyna bolts 50 mm deep (Supplied) Level bench by adjusting Leveling Feet.
ELECTRICAL WIRING REQUIRMENTS:
Electrical wiring to waterproof GPO 10 amp to AS3000:2007 standard requires a minimum of 2.5 mm² cabling for each Greenplate Inbench
barbecue unit, larger for long runs, with each barbecue unit having its own 20 amp RCBO C-Curve type A in the mains sub-board.
“Under No circumstance should more than one barbecue unit be on one power line. Failure to install correctly will VOID
the warranty as damage to the electrical equipment will occur.”
SINGLE GPO POWER POINT WITH
SEPARATE 10 AMP CIRCUIT FOR
EACH INBENCH BBQ UNIT TO BE
INSTALLED 100 mm CENTRE FROM
BOTTOM FOLD OF THE RIGHT SIDE
PANEL ON A GPO SUPPORT POST.

S:\Libraries\Documents\Greenplate BBQ Info\Equal Access Single Barbecue Bench Installation Information PID.doc | Updated 16-07-2018
Page 2of 2
I
IM
MP
PO
OR
RT
TA
AN
NT
T
I
IN
NS
ST
TA
AL
LL
LA
AT
TI
IO
ON
N
R
RE
EQ
QU
UI
IR
RE
EM
ME
EN
NT
TS
S
F
FO
OR
R
T
TH
HE
E
G
GR
RE
EE
EN
NP
PL
LA
AT
TE
E
®
®
P
PI
ID
D
I
IN
NB
BE
EN
NC
CH
H
B
BA
AR
RB
BE
EC
CU
UE
E
U
UN
NI
IT
T
1. Correct wiring of the Greenplate ® Barbecue is essential. Incorrect installation will void the Warranty. Each Greenplate ® barbecue plate
must have its own 10 amp circuit with a 20 amp RCBO C-Curve type A. Having a rated residual operating current not exceeding 30mA in
the sub-board, as per AS3000.2007 standard requires a minimum of 2.5 mm² cabling for each unit for longer runs larger cabling will be
required. If unsure contact Greenplate Pty Ltd service on 0411 845 534. An Australian approved 3 pins, 10 amp electrical extension lead
is required as a supply cord, maximum length 2 meters. All electrical work must be carried out by appropriated electrical licenced
personnel in accordance with the National wiring rules.
2. Unit must be installed in a weather proof enclosure to IPX4 or equivalent, minimum 50 mm clearance around electrical housing is
required. Please protect barbecue plate and benches from industrial fallout during any construction as rust from filings or chemicals
will not be covered under warranty
3. Benches not supplied by Greenplate Pty Ltd must be adequately cross ventilated. Ventilate bench to allow free air flow through cabinet.
Failure to ventilate the bench can result in premature failure of equipment, this is not covered under warranty. Cross Ventilation area of
0.035m² required. All Greenplate ® benches are pre-fitted with adequate ventilation.
4. Cut square hole into bench top where desired (490 mm x 490 mm). Carefully lower Greenplate ® 300 unit into opening. Install lockdown U
bracket, threaded drain pipe and washers as per (Figure 3.). Position Remote ON/Off push button switch to your desired location (19 mm hole).
Mount switch plate, instruction and safety labels to outside of bench.
5. Ensure appropriate grease collection bin and bag (supplied) is placed under the drain tube.
6. Plug extension lead (not supplied) into input socket of the unit (Figure 1.) and then into wall socket outlet having an earth contact (10 amp, 230
VAC) and turn ON (at wall only). Set thermostat to your required temperature (Figure 1.) 320°C is recommended, for general use.
7. Switch on mains power, wait thirty seconds BBQ will beep once for 50 hz twice for 60 hz. Unit will ‘energize’ printed circuit board. Press switch. A
buzzer will sound once and the push button switch will light red when BBQ is heating and green when desired cooking temperature is reached.
The timer is preset to switch off the barbecue after 28 minutes. To stop barbecue during cycle press and hold the switch for 5 seconds.
8. A security setting is available by switching the micro switch # 2 on the PCB control board to on position all other dipswitches off.
This selects the press and hold, for the six seconds delay function, and should be accessed by qualified personnel only.
9. Buzzer will sound three times at the end of the 28 minute cooking cycle.
10. Clean the plate prior to use with warm soapy water to remove any dirt and for safe hygienic cooking. Ensure the plate is cleaned
regularly to maintain its appearance and longevity.
11. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
12. WARNING: Charcoal or similar combustible fuels must not be used with this appliance
Greenplate Service Line 0411 845 534
Greenplate is a registered trademark
ABN 71 112 123 038 | ACN 112 123 038
UNIT 2/15 NATASHA STREET
CAPALABA 4157 QUEENSLAND AUSTRALIA
WEB: www.greenplate.com.au EMAIL: info@greenplate.com.au
PHONE: (07) 3245 3008 FACSIMILE: (07) 3245 3009
Table of contents
Other Greenplate Grill manuals
Popular Grill manuals by other brands

Kenmore
Kenmore 415.16123800 Use and care guide

Camp Chef
Camp Chef PG24CLAU Warning & instruction booklet

Tucker Barbecues
Tucker Barbecues GTR Series Assembly, installation and operating instructions

Monogram
Monogram ZGG540NCP1SS owner's manual

Equipex
Equipex Sodir Savoy Operation manual

Gaggenau
Gaggenau VR 414 610 use and care manual
















