Greenheck FGI Series User manual

Assembly Instructions

Document #471321

Fabra Hood • Form B

Single Section with Birdscreen

Throat length less than or equal to 72 inches

STEP 1

Fabra Hood • Form B

Step 1 - Fabra hood B #471321

Open the shipping crates and separate the parts

according to the size of the unit (See ﬁgure No.1 on

attached "PARTS LIST")

STEP 2

Figure 2 Fabra hood B #471321

Figure 2

Place the two BASE ENDS and the two BASE SIDES

in their approximate relationship to each other. (See

Figure 2) Fasten together using three (3) 1⁄4-20 fasteners

per corner for 5 inch high base and four (4) 1⁄4-20

fasteners per corner for 12 inch high base.

Note: Fasteners should be hand tightened only until

step 4. On some units where the difference between the

hood width and throat width is greater than 32 inches, a

REINFORCING PLATE is required in the corners of the

BASE. (See Figure 2, DETAIL "A")

STEP 3

STEP 4

2Fabra Hood • Form B

Figure 3 Fabra hood B #471321

Attach the HOOD SUPPORT ANGLE to the BASE

ASSEMBLY, using four (4) 1⁄4-20 fasteners per angle.

(See Figure 3, DETAIL "B") On some units two (2)

DIAGONAL BRACES come pre-attached to the

HOOD SUPPORT ANGLE. Fasten the loose end of

the DIAGONAL BRACES to the BASE ASSEMBLY,

using one (1) 1⁄4-20 FASTENER PER diagonal brace.

(See Figure 3, DETAIL "C")

Figure 3

Tighten all fasteners. Caulk all inside corners where the

base sections came together. At this point, the base

may be lifted onto the roof curb before proceeding with

further assembly.

STEP 5

Figure 4 Fabra hood B #471321

Attach the SIDE BIRDSCREEN ASSEMBLY to the HOOD

SUPPORT ANGLE and BASE ASSEMBLY, using four (4)

1⁄4-20 X 1" fasteners per screen assembly. (See Figure 4)

Figure 4

STEP 6

STEP 7

Fabra Hood • Form B

Figure 5 Fabra hood B #471321

Figure 5

Install the END BIRDSCREEN ASSEMBLY. (See Figure 5)

Turn the BIRDSCREEN CLIPS (Which are pre-assembled

to the END BIRDSCREEN ASSEMBLY) so that two (2)

are under the SIDE BIRDSCREEN FRAME EXTENSION

and the other two (2) are under the HOOD SUPPORT

ANGLE, and tighten down. (See Figure 5, DETAIL "D")

Attach the HOOD RAIL ASSEMBLY to the HOOD

SUPPORT ANGLES, using two (2) 3⁄8x 3⁄4inch fasteners

per HOOD RAIL ASSEMBLY. (See Figure 6) NOTE:

Fasteners should be hand tightened only until step 8.

Figure 6 Fabra hood B #471321

Figure 6

STEP 8

STEP 9

Phone: (715) 359-6171 • Fax: (715) 355-2399 • E-mail: [email protected] • Website: www.greenheck.com

Figure 7 Fabra hood B #471321

Step 9 Fabra hood B #471321

Assemble HOOD PANELS to HOOD RAIL ASSEMBLY.

The HOOD END ASSEMBLY with the MALE RIB is to

be installed ﬁrst. (See Figure 7, DETAIL "E") Place the

remaining HOOD PANELS in place, interlocking panels

as you go. (See DETAIL "E") Secure each HOOD PANEL

to the HOOD RAIL ASSEMBLY as it is put in place,

using four (4) No. 12 X 3⁄8inch sheet metal screws with

sealing washers per HOOD PANEL. The HOOD END

ASSEMBLY with the FEMALE RIB is to be installed

last. NOTE: Hoods over 9 Ft. wide are supplied with

special HOOD CLIPS. (See DETAIL "F" in step 9)

HOOD PANELS have predrilled holes for HOOD CLIP

installation. Install CLIPS as HOOD PANELS are being

put in place, using one (1) No. 12 X 5⁄8inch sheet metal

screw with sealing washer per HOOD CLIP. To install

CLIPS in the last panel, leave the END BIRDSCREEN

ASSEMBLY out to provide access to the underside of

the hood. The END BIRDSCREEN ASSEMBLY can be

easily replaced after the hood is completely assembled.

Figure 7

Tighten all pivot bracket fasteners. NOTE: There may be extra fasteners.

This manual suits for next models

Table of contents

Other Greenheck Ventilation Hood manuals

Greenheck

Greenheck UL 555S Leakage Class II SSSMDR-502 User manual

Greenheck

Greenheck 458292 User manual

Greenheck

Greenheck Steel 3V Blades OFSD-212 User manual

Greenheck

Greenheck KFD Series User manual

Greenheck

Greenheck Vektor-MH User manual

Greenheck

Greenheck Combination Fire Smoke Dampers SSFSD-211 User manual

Greenheck

Greenheck G User manual

Greenheck

Greenheck QEI User manual

Greenheck

Greenheck Extruded Backdraft Damper EM-40 User manual

Greenheck

Greenheck DFD-155 User manual

Greenheck

Greenheck Steel Airfoil Blades SMD-301M User manual

Greenheck

Greenheck FSD Series Owner's manual

Greenheck

Greenheck H-CUBE. User manual

Greenheck

Greenheck Exhaust Fan SMD-302M User manual

Greenheck

Greenheck Belt Drive Duct Fan BDF User manual

Greenheck

Greenheck Vektor-MH User manual

Greenheck

Greenheck CFSD-XXX Series Owner's manual

Greenheck

Greenheck FSD Series Owner's manual

Greenheck

Greenheck WD-400 Series User manual

Greenheck

Greenheck MultiSpec SP-LP0511 User manual

Greenheck

Greenheck Fire Smoke Dampers FSDGB-211 User manual

Greenheck

Greenheck ERD User manual

Greenheck

Greenheck Steel Airfoil Blades FSD-331 User manual

Greenheck

Greenheck CFSD Series User manual

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual