Greenheck SP110L User manual

Service Parts

Key

No.

Greenheck

Part No.

Description

1 435100 Mounting Frame

2 435101 Knockout Plate & Screws

3 435102 Housing

4 435103 Wiring Panel/Harness Assembly

5434112 Control Assembly & Motor (SP80L)

435113 Control Assembly & Motor (SP110L)

6 435106 Duct Connector - 6"

7 435114 6" to 4" Reducer (model SP80L only)

8 435108 Blower Wheel

9 435115 Scroll Assembly

10 435117 Grille Assembly (includes 11, 12, 13)

11 435111 Grille Spring (2 req’d)

12 435118 Lens

13 435119 Bulb, GU24 18W 3500K FL (2 req’d)

Table of Contents

Warnings and Cautions ............................................ 2

Typical Installation .................................................... 2

New Construction Installation .................................. 3

Retroﬁt Installation ................................................... 7

Easy installation in both new construction and retroﬁt.

Model SP110L / SP80L

Operation................................................................ 11

Cleaning and Maintenance..................................... 12

Troubleshooting...................................................... 12

Our Commitment.................................................... 12

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble,

install, operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with instructions could result in personal injury and/or property damage!

SP Ceiling Exhaust Fans

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble,

install, operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with instructions could result in personal injury and/or property damage!

Document 99045144B

Model SP110L/SP80L

Lighted Multi-Speed

Ceiling Exhaust Fan

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address or telephone number

listed in the warranty.

2. Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnecting

means to prevent power from being switched

on accidentally. When the service disconnecting

means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the

service panel.

3. Installation work and electrical wiring must be

done by a qualified person(s) in accordance with

all applicable codes and standards, including fire-

rated construction codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent backdrafting.

Follow the heating equipment manufacturer’s

guideline and safety standards such as those

published by the National Fire Protection

Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code

authorities.

5. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the

outdoors.

7. Do not use this fan with any solid-state speed

control device.

8. Acceptable for use over a tub or shower when

connected to a GFCI (Ground Fault Circuit

Interrupter) - protected branch circuit.

9. This unit must be grounded.

CAUTION

For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

1. This product is designed for installation in ceilings

up to a 12/12 pitch (45 degree angle). Duct

connector must point up. DO NOT MOUNT THIS

PRODUCT IN A WALL.

2. To avoid motor bearing damage and noisy and/

or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

3. Please read specification label on product for

further information and requirements.

CAUTION

NOT FOR USE IN A COOKING AREA

Typical Installation

• Installation is the same for:

• Fits in 2" x 8" ceiling construction.

• Inﬁnitely adjust the fan position between

joists from 14" to 24"

on center.

*Purchase

separately.

INSULATION*

(Place around and

over Fan Housing.)

ROOF CAP*

(with built-in

damper)

FAN

HOUSING

POWER

CABLE*

ROUND

DUCT*

ROUND

ELBOWS*

Seal gaps

around

Housing.

Seal duct

joints with

tape.

Keep duct

runs short.

WALL CAP*

(with built-in

damper)

Joists I-Joists Trusses

2SP Ceiling Exhaust Fans ®

Parts Bag holds

Knockout Plate

and six (6) screws

Remove

Instruction

Sheet

Remove CFL Bulbs

from protective packaging Punch out Mask from

packaging. See Step 6.

New Construction Installation

Tools needed

Power screwdriver with a Phillips bit

Phillips screwdriver

Flathead screwdriver

Pliers

Wire insulation stripper

Wire cutter

Materials needed

• 6" round metal ducting recommended for best

performance. Use of other ducting is acceptable but

may impact performance.

• Roof cap or wall cap (built-in damper recommended)

• Tape to seal duct connections

• Electrical wiring and supplies per local code

requirements

• 4W (max.) C7-type night light bulb

1 - Remove Packaging

2 - Install Mounting Frame

SP Ceiling Exhaust Fans

Position Housing

between joists and

crimp channel

on both sides of

Mounting Frame

to lock Housing in

place. Do not crimp

Housing.

Screws from Parts Bag

Top and bottom ﬂanges

go outside Housing

Insert tab into slot

inside Housing

Screw from

Parts Bag

6" to 4" Reducer provided in select models

Tape

6" Ducting 4" Ducting

snap!

New Construction Installation

3 - Snap-in and Secure Housing

4 - Attach Duct Connector and Ducting

4SP Ceiling Exhaust Fans ®

2Screw from

Parts Bag

Attach cable clamps to

Knockout Plate. Knockout Plate

mounts to outside of Housing

and may be oriented as desired.

Connect wires

Fan Light

5 - Connect Wires and Install Knockout Plate

• Run 120VAC electrical wiring to the installation

location.

• Use proper UL-approved connectors to secure wiring

to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

• Do not use a dimmer switch to operate the light.

New Construction Installation

LINE

IN GRD GRD

WHT WHT

WHT

BLK

BLK BLU

BLK

RED RED (Rated Level)

REDRED

BLK*

MASTER

ON/OFF

SWITCH

FAN

MODE

SELECT

SWITCH

FAN

LIGHT

LIGHT NIGHT

LIGHT

NIGHT

LIGHT

UNITSWITCH BOX (* Adjustable Level)

(2) 2-FUNCTION

CONTROLS

KNOCKOUT

PLATE

FAN

RECEPTACLE

LIGHT

RECEPTACLE

LIGHT

RECEPTACLE

WIRES

FAN

RECEPTACLE

WIRES

(2) 2-FUNCTION CONTROLS

(purchase separately) 120 VAC

LINE IN

MODE

SELECT

MASTER

ON/OFF

SWITCH

FAN

SWITCH

BOX

LIGHT

NIGHT

LIGHT

BLACK

WHITE

BLUE

RED

GROUND

(green or bare)

SP Ceiling Exhaust Fans

Mask protects unit

during construction.

Remove before

installing Grille.

6 - Insert Mask and Finish Ceiling

7 - Install Grille

NOTE: See Page 11 for Operations, Page 12 for

Cleaning and Maintenance, and Troubleshooting.

New Construction Installation

• Install ceiling material.

• Cut out around Housing.

Night Light

(purchase separately)

8 - Install Bulbs

6SP Ceiling Exhaust Fans ®

12" (30.5 cm)

Parts Bag holds

Knockout Plate

and six (6)

screws

Existing ductwork and

wiring left in place

11" (27.9 cm)

parallel with joists

Remove

Instruction

Sheet

Remove CFL Bulbs

from protective packaging Punch out Mask from

packaging. See Step 12.

Retroﬁt Installation

Examine the existing wiring to make sure it is not

damaged. If any damage is found,

DO NOT CONTINUE INSTALLATION of this product.

Contact a qualiﬁed person(s) for repair.

1 - Remove Packaging

2 - Switch Off Power

4 - Examine Wiring

3 - Enlarge Ceiling Opening and Remove Existing Fan

Materials needed

• Tape to seal duct connections

• Existing rigid duct will require the addition of a short

length of ﬂexible duct

• Electrical wiring and supplies per local code

requirements

• 4W (max.) C7-type night light bulb

Tools needed

Power screwdriver with a Phillips bit

Phillips screwdriver Ruler

Flathead screwdriver Pencil

Pliers Drywall saw

Wire insulation stripper Claw hammer or pry bar

Wire cutter Utility knife

WARNING

Before removing existing fan, switch power off at

service panel and lock the service disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

SP Ceiling Exhaust Fans

Both sides

Set aside

Blower Assembly

Set aside

Wiring Panel

Set aside

screw

Bend up

four tabs

Remove screws

from Mounting

Frame and set aside

Retroﬁt Installation

5 - Remove Blower Assembly

6 - Remove Wiring Panel

7 - Insert Mounting Frame

8SP Ceiling Exhaust Fans ®

4Screw from

Parts Bag

Screws set aside

in Step 7

Pull existing wiring into

Housing as it is inserted

into Mounting Frame

Pull existing

ductwork

into Housing

Insert tab into

slot inside

Housing

snap!

6" to 4" Reducer provided in select models

Tape

6" Ducting 4" Ducting

Retroﬁt Installation

10 - Attach Ducting and Duct Connector

8 - Secure Mounting

Frame

9 - Snap-in Housing

SP Ceiling Exhaust Fans

12 3

If ceiling repairs are needed,

place Mask in Housing after

Blower Assembly is secured.

See New Construction

Installation Step 6. Remove

Mask before installing Grille.

Screws from Parts Bag

12 - Insert and Secure

Blower Assembly

Screw from

Parts Bag

Connect wires

Fan

Light

Screw set

aside in

Step 6

Attach cable

clamps to

Knockout Plate.

Knockout Plate

mounts to inside

of Housing and

maybe oriented

as desired.

LINE

IN GRD GRD

WHT WHT

WHT

BLK

BLK BLU

BLK

RED RED (Rated Level)

REDRED

BLK*

MASTER

ON/OFF

SWITCH

FAN

MODE

SELECT

SWITCH

FAN

LIGHT

LIGHT NIGHT

LIGHT

NIGHT

LIGHT

UNITSWITCH BOX (* Adjustable Level)

(2) 2-FUNCTION

CONTROLS

KNOCKOUT

PLATE

FAN

RECEPTACLE

LIGHT

RECEPTACLE

LIGHT

RECEPTACLE

WIRES

FAN

RECEPTACLE

WIRES

(2) 2-FUNCTION CONTROLS

(purchase separately) 120 VAC

LINE IN

MODE

SELECT

MASTER

ON/OFF

SWITCH

FAN

SWITCH

BOX

LIGHT

NIGHT

LIGHT

BLACK

WHITE

BLUE

RED

GROUND

(green or bare)

Retroﬁt Installation

11 - Install Knockout Plate,

Connect Wires and Install

Wiring Panel

• Use proper UL-approved connectors

to secure wiring to the Knockout Plate

provided in Parts Bag.

• Connect wires as shown in wiring

diagram.

• Do not use a dimmer switch to

operate the light.

10 SP Ceiling Exhaust Fans ®

This manual suits for next models

Table of contents

Languages:

Other Greenheck Fan manuals

Greenheck

Greenheck G Series User manual

Greenheck

Greenheck SFD User manual

Greenheck

Greenheck SP-L User manual

Greenheck

Greenheck SQ 60-75 User manual

Greenheck

Greenheck FGI Fabra Hood User manual

Greenheck

Greenheck SQ User manual

Greenheck

Greenheck Combination Fire Smoke Damper FSD-211 User manual

Greenheck

Greenheck CRD-501 Manual

Greenheck

Greenheck DS User manual

Greenheck

Greenheck Vektor ERS-MD User manual

Greenheck

Greenheck SDPHE User manual

Greenheck

Greenheck APEX-200 Instruction manual

Greenheck

Greenheck USF-200 Instruction manual

Greenheck

Greenheck CUBE-098 Installation guide

Greenheck

Greenheck MiniVent User manual

Greenheck

Greenheck FGI User manual

Greenheck

Greenheck WTHD series Instruction manual

Greenheck

Greenheck VersiVent VER-45 User manual

Greenheck

Greenheck Axial Fans User manual

Greenheck

Greenheck SQ-M 70 User manual

Greenheck

Greenheck SQ User manual

Greenheck

Greenheck ERV User manual

Greenheck

Greenheck SQ User manual

Greenheck

Greenheck BIDW User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual