Greenheck SP110 General instructions

Service Parts

Key

No.

Greenheck

Part No.

Description

1 435100 Mounting Frame

2 435101 Knockout Plate & Screws

3 435102 Housing

4 435109 Wiring Panel/Harness Assembly

5435104 Control Assembly & Motor (SP80)

435105 Control Assembly & Motor (SP110)

6 435106 Duct Connector - 6"

7 435107 6" to 4" Reducer (model SP80 only)

8 435108 Blower Wheel

9 435116 Scroll Assembly

10 435110 Grille Assembly (includes 11)

11 435111 Grille Spring (2 req’d)

Table of Contents

Warnings and Cautions ............................................ 2

Typical Installation .................................................... 2

New Construction Installation .................................. 3

Retroﬁt Installation ................................................... 7

Easy installation in both new construction and retroﬁt.

Operation................................................................ 11

Cleaning and Maintenance..................................... 12

Troubleshooting...................................................... 12

Our Commitment.................................................... 12

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble,

install, operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with instructions could result in personal injury and/or property damage!

SP Ceiling Exhaust/Inline Fans

Model SP110 / SP80

Document 99045143B

Model SP110/SP80

Multi-Speed

Ceiling Exhaust Fan

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address or telephone number

listed in the warranty.

2. Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnecting

means to prevent power from being switched

on accidentally. When the service disconnecting

means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the

service panel.

3. Installation work and electrical wiring must be

done by a qualified person(s) in accordance with

all applicable codes and standards, including fire-

rated construction codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent backdrafting.

Follow the heating equipment manufacturer’s

guideline and safety standards such as those

published by the National Fire Protection

Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code

authorities.

5. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the

outdoors.

7. Do not use this fan with any solid-state speed

control device.

8. Acceptable for use over a tub or shower when

connected to a GFCI (Ground Fault Circuit

Interrupter) - protected branch circuit.

9. This unit must be grounded.

CAUTION

For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

1. This product is designed for installation in ceilings

up to a 12/12 pitch (45 degree angle). Duct

connector must point up. DO NOT MOUNT THIS

PRODUCT IN A WALL.

2. To avoid motor bearing damage and noisy and/

or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

3. Please read specification label on product for

further information and requirements.

CAUTION

NOT FOR USE IN A COOKING AREA

Typical Installation

• Installation is the same for:

• Fits in 2" x 8" ceiling construction.

• Inﬁnitely adjust the fan position

between joists from 14" to 24"

on center.

*Purchase

separately.

INSULATION*

(Place around and

over Fan Housing.)

ROOF CAP*

(with built-in

damper)

FAN

HOUSING

POWER

CABLE*

ROUND

DUCT*

ROUND

ELBOWS*

Seal gaps

around

Housing.

Seal duct

joints with

tape.

Keep duct

runs short.

WALL CAP*

(with built-in

damper)

Joists I-Joists Trusses

2SP Ceiling Exhaust Fans ®

New Construction Installation

Tools needed

Power screwdriver with a Phillips bit

Phillips screwdriver

Flathead screwdriver

Pliers

Wire insulation stripper

Wire cutter

Materials needed

• 6" round metal ducting recommended for best

performance. Use of other ducting is acceptable but

may impact performance.

• Roof cap or wall cap (built-in damper recommended)

• Tape to seal duct connections

• Electrical wiring and supplies per local code

requirements

1 - Remove Packaging

2 - Install Mounting Frame

Parts Bag holds

Knockout Plate

and six (6)

screws

Remove

Instruction

Sheet

Punch out Mask from

packaging. See Step 6.

SP Ceiling Exhaust Fans

New Construction Installation

3 - Snap-in and Secure Housing

4 - Attach Duct Connector and Ducting

Position Housing

between joists and

crimp channel on both

sides of Mounting Frame

to lock Housing in place.

Do not crimp Housing.

Screws from Parts Bag

Top and bottom ﬂanges

go outside Housing

Insert tab into slot

inside Housing

Screw from

Parts Bag

6" to 4" Reducer provided in select models

Tape

6" Ducting 4" Ducting

snap!

4SP Ceiling Exhaust Fans ®

5 - Connect Wires and Install Knockout Plate

• Run 120VAC electrical wiring to the installation

location.

• Use proper UL-approved connectors to secure wiring

to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

Screw from

Parts Bag

Attach cable clamp to Knockout

Plate. Knockout Plate mounts to

outside of Housing and may be

oriented as desired.

Connect wires

LINE

IN GRD GRD

WHT

BLK

BLK BLK (Adjustable Level)

RED

WHT

WHTRED

(Rated

Level)

MASTER

ON/OFF

SWITCH MODE

SELECT

SWITCH

FAN

UNITSWITCH BOX

LINE

IN GRD GRD

WHT

BLK

BLK BLK

RED

WHT

WHTRED

MASTER

ON/OFF

SWITCH

MASTER

ON/OFF

SWITCH*

MODE

SELECT

SWITCH

MODE

SELECT

SWITCH*

FAN

UNITSWITCH BOX

KNOCKOUT

PLATE

RECEPTACLE

120 VAC

LINE IN

SWITCH BOX

BLACK

WHITE

RED

GROUND (green or bare)

*purchase separately

New Construction Installation

SP Ceiling Exhaust Fans

6 - Insert Mask and Finish Ceiling

7 - Install Grille

NOTE: See Page 11 for Operations, Page 12 for

Cleaning and Maintenance, and Troubleshooting.

New Construction Installation

• Install ceiling material.

• Cut out around Housing.

Mask protects unit

during construction.

Remove before

installing Grille.

6SP Ceiling Exhaust Fans ®

WARNING

Before removing existing fan, switch power off at

service panel and lock the service disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

12" (30.5 cm)

Retroﬁt Installation

Parts Bag holds

Knockout Plate

and six (6)

screws

Existing ductwork and

wiring left in place

11" (27.9 cm)

parallel with joists

Examine the existing wiring to make sure it is not

damaged. If any damage is found,

DO NOT CONTINUE INSTALLATION of this product.

Contact a qualiﬁed person(s) for repair.

Remove

Instruction

Sheet

Punch out Mask from

packaging. See Step 12.

1 - Remove Packaging

2 - Switch Off Power

4 - Examine Wiring

3 - Enlarge Ceiling Opening and Remove Existing Fan

Materials needed

• Tape to seal duct connections

• Existing rigid duct will require the addition of a short

length of ﬂexible duct

• Electrical wiring and supplies per local code

requirements

Tools needed

Power screwdriver with a Phillips bit

Phillips screwdriver Ruler

Flathead screwdriver Pencil

Pliers Drywall saw

Wire insulation stripper Claw hammer or pry bar

Wire cutter Utility knife

SP Ceiling Exhaust Fans

Retroﬁt Installation

5 - Remove Blower Assembly

6 - Remove Wiring Panel

7 - Insert Mounting Frame

Both sides

Set aside

Blower Assembly

Set aside

Wiring Panel

Set aside

screw

Bend up

four tabs

Remove screws from

Mounting Frame

and set aside

8SP Ceiling Exhaust Fans ®

Retroﬁt Installation

Screw from

Parts Bag

Screws set

aside

in Step 7

Pull existing wiring into

Housing as it is inserted

into Mounting Frame

Pull existing

ductwork

into Housing

Insert tab

into slot

inside

Housing

10 - Attach Ducting and

Duct Connector

8 - Secure Mounting

Frame

9 - Snap-in Housing

snap!

6" to 4" Reducer provided in select models

Tape

6" Ducting 4" Ducting

SP Ceiling Exhaust Fans

LINE

IN GRD GRD

WHT

BLK

BLK BLK

RED

WHT

WHTRED

MASTER

ON/OFF

SWITCH

MASTER

ON/OFF

SWITCH*

MODE

SELECT

SWITCH

MODE

SELECT

SWITCH*

FAN

UNITSWITCH BOX

KNOCKOUT

PLATE

RECEPTACLE

120 VAC

LINE IN

SWITCH BOX

BLACK

WHITE

RED

GROUND (green or bare)

*purchase separately

Retroﬁt Installation

11 - Install Knockout Plate, Connect

Wires and Install Wiring Panel

Screw from

Parts Bag

Attach cable clamp to Knockout

Plate. Knockout Plate mounts to

inside of Housing and may be

oriented as

desired.

Connect

wires

Screw set

aside in

Step 6

• Use proper UL-approved connectors to secure wiring

to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

LINE

IN GRD GRD

WHT

BLK

BLK BLK (Adjustable Level)

RED

WHT

WHTRED

(Rated

Level)

MASTER

ON/OFF

SWITCH MODE

SELECT

SWITCH

FAN

UNITSWITCH BOX

10 SP Ceiling Exhaust Fans ®

This manual suits for next models

Table of contents

Languages:

Other Greenheck Fan manuals

Greenheck

Greenheck 240XP-CUB User manual

Greenheck

Greenheck ERV Series User manual

Greenheck

Greenheck Series L User manual

Greenheck

Greenheck APEX-200 Instruction manual

Greenheck

Greenheck VersiVent VER-45 User manual

Greenheck

Greenheck ARC User manual

Greenheck

Greenheck MiniVent User manual

Greenheck

Greenheck BIDW User manual

Greenheck

Greenheck RV-35 User manual

Greenheck

Greenheck TBI User manual

Greenheck

Greenheck SP-A User manual

Greenheck

Greenheck CRD-3 Series Installation guide

Greenheck

Greenheck FGI User manual

Greenheck

Greenheck MiniVent Series User manual

Greenheck

Greenheck Combination Fire Smoke Damper FSD-211 User manual

Greenheck

Greenheck CUE Series User manual

Greenheck

Greenheck ERVe Series User manual

Greenheck

Greenheck CUBE-098 Installation guide

Greenheck

Greenheck FA/103-00 User guide

Greenheck

Greenheck ERS-MD User manual

Greenheck

Greenheck IGX-HV User manual

Greenheck

Greenheck ERCH User manual

Greenheck

Greenheck SP-B Installation and operating instructions

Greenheck

Greenheck ECV Series User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual