Graco Dyna-Star 236753 Operation manual
308–390
Rev. D
Supersedes Rev. C
First
choice when
quality counts.
INSTRUCTIONS-PARTS
LIST
INSTRUCTIONS
This
manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
Dyna-Star
HYDRAULIC RECIPROCATOR AND PUMP
1500 psi (10 MPa, 102 bar) Maximum Hydraulic Input Pressure
375 psi (2.6 MPa, 26 bar) Maximum Fluid Outlet Pressure
FOR
LUBRICA
TING FLUIDS ONL
Y
1/4:1
RA
TIO UNIVERSAL PUMP AND RECIPROCATOR
Model 236–753, Series C, stubby length
RECIPROCAT
OR ONL
Y
Model 239–884, Series A
WARNING
The
pump is designed to dispense lube products
only
. Any other fluids can cause unsafe operating
conditions and result in component rupture, fire or
explosion which could cause serious injury
, includ
-
ing fluid injection.
Table
of Contents
Warnings 2.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation 8.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service 11.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reciprocator
Repair
14.
. . . . . . . . . . . . . . . . . . . . . . . . . .
Displacement
Pump Repair
18.
. . . . . . . . . . . . . . . . . . . .
Parts
List & Drawing
Universal 1/4:1 Ratio Displacement Pump
19.
. . . . .
Reciprocator 20
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical
Data
23.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensional
Drawing and Mounting Hole Layout
23.
.
Warranty 24
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco
Phone Number
24.
. . . . . . . . . . . . . . . . . . . . . . . . .
GRACO INC. P.O. BOX 1441
MINNEAPOLIS, MN
55440–1441
http://www.graco.com
COPYRIGHT
1994, GRACO INC.
Graco
Inc. is registered to I.S. EN ISO 9001
Model
236–753 shown
Patent No. 4,383,475
Foreign Patents Pending
Patent 1984 Canada
Brevete 1984
Symbols
Warning Symbol
WARNING
This
symbol alerts you to the possibility of serious
injury or death if you do not follow the corresponding
instructions.
Caution Symbol
CAUTION
This
symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.
EQUIPMENT MISUSE HAZARD
Equipment
misuse can cause the equipment to rupture or malfunction and result in serious injury
.
D
This equipment is for professional use only
.
D
Read all instruction manuals, tags, and labels before you operate the equipment.
D
Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor
.
D
Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D
Check equipment daily
. Repair or replace worn or damaged parts immediately
.
D
Do not exceed the maximum working pressure of the lowest rated component in your system.
This equipment has a
1500 psi (10 MPa, 102 bar) maximum hydraulic input pressure and
375 psi (2.6 MPa, 26 bar) maximum fluid outlet pressure.
D
Use fluids and solvents that are compatible with the equipment wetted parts. Refer to the
T
echnical Data
section of all equipment manuals. Read the fluid and solvent manufacturer
’s
warnings.
D
Handle hoses carefully
. Do not pull on hoses to move equipment.
D
Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not
expose Graco hoses to temperatures above 82
_
C (180
_
F) or below –40
_
C (–40
_ F).
D
Do not lift pressurized equipment.
D
Comply with all applicable local, state, and national fire, electrical, and safety regulations.
WARNING
WARNING
FLUID INJECTION HAZARD
Fluid
from the dispensing valve, leaks or ruptured components can inject fluid into your body and
cause extremely serious injury
, including the need for amputation. Fluid splashed in the eyes or on
the skin can also cause serious injury
.
Fluid injected into the skin might look like just a cut, but it is a serious injury
.
Get immediate
medical attention.
Do not point the dispensing valve at anyone or at any part of the body
.
Do not put your hand or fingers over the end of the dispensing valve.
Do not stop or deflect leaks with your hand, body
, glove or rag.
Use only extensions and couplers that are designed for use with your dispensing valve.
Do not use a low pressure flexible nozzle with this equipment.
Follow the
Pressure Relief Procedure
on page 8 if the grease fitting coupler clogs and before
cleaning, checking or servicing the equipment.
T
ighten all fluid connections before operating the equipment.
Check the hoses, tubes, and couplings daily
. Replace worn or damaged parts immediately
. Do
not repair high pressure couplings; you must replace the entire hose.
Fluid hoses must have spring guards on both ends, to help protect them from rupture caused by
kinks or bends near the couplings.
TOXIC FLUID HAZARD
Hazardous
fluids or toxic fumes can cause serious injury or death if splashed in the eyes or on the
skin, inhaled, or swallowed.
Know the specific hazards of the fluid you are using.
Store hazardous fluid in an approved container
. Dispose of hazardous fluid according to all local,
state, and national guidelines.
Always wear protective eyewear
, gloves, clothing, and respirator as recommended by the fluid
and solvent manufacturer
.
WARNING
WARNING
HALOGENATED HYDROCARBON HAZARD
Never
use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in aluminum pumps. Such use could result in a serious chemical
reaction, with the possibility of explosion, which could cause death, serious injury
, and/or substantial
property damage.
Consult your fluid suppliers to ensure that the fluids used are compatible with aluminum parts.
4 308-390
MOVING
P
ARTS HAZARD
Moving
parts can pinch or amputate your fingers.
Keep clear of all moving parts when you start or operate the pump.
Before you service the equipment, follow the
Pressure Relief Procedure
on page 8 to prevent
the equipment from starting unexpectedly
.
FIRE AND EXPLOSION HAZARD
Improper
grounding, poor ventilation, open flames, or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury
.
Ground the equipment and the object being sprayed. Refer to
Grounding
on page 7.
If there is any static sparking or you feel an electric shock while using this equipment,
stop
spraying immediately
.
Do not use the equipment until you identify and correct the problem.
Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
Keep the spray area free of debris, including solvent, rags, and gasoline.
Before operating this equipment, electrically disconnect all equipment in the spray area.
Before operating this equipment, extinguish all open flames or pilot lights in the spray area.
Do not smoke in the spray area.
Do not turn on or of
f any light switch in the spray area while spraying or while there are any
fumes in the air
.
Do not operate a gasoline engine in the spray area.
WARNING
WARNING
United States Government safety standards have been adopted under the Occupational Safety and Health Act.
Y
ou should consult these standards––particularly the General Standards, Part 1910.
5308-390
Installation
KEY
BPorous
plug (weep tube optional)
C
Fluid dispenser outlet
D
Drain valve (required)
F
Hydraulic return line,
minimum 3/4” I.D. (required)
G
Hydraulic outlet, 3/4 npt
H
Return line shutof
f valve,
minimum 3/4” (required)
J
Hydraulic inlet, 3/8 npt
K*
Supply line shutof
f valve
L*
Pressure gauge
M*
Pressure reducing valve
(required
in systems over 1500
psi
[10
MPa, 102 bar])
N*
Flow control valve
(required in systems over 3 gpm
[1
1 lpm])
P
Hydraulic supply line (use only
graco hydraulic power supply)
Q
Material supply
R
Ground wire (required)
SW
all mounting bracket 236–778
(see manual 308–394)
Typical
Installation – Suction Feed System
Fig. 1 03516
R
F
P
H
K
M
N
B
J
Q
D
C
L
G
S
*Included
in Hydraulic Fluid Control Kit 236–864, which can be ordered separately
.
Although
the installation shown in Fig. 1 is only a guide
for selecting and installing system components and
accessories, some of the equipment is required, as
noted in the key. For assistance in designing a system
to suit your needs, contact your Graco distributor
.
Mount the pump to suit the type of installation planned.
WARNING
Mount the pump securely so that it cannot move
around during operation. Failure to do so could
result in personal injury or equipment damage.
Maximum W
orking Pressure of Accessories
T
o reduce the risk of serious bodily injury including
fluid injection and splashing in the eyes or on the
skin, which may be caused if a component rup
-
tures, all accessories added to the reciprocator
power supply side must have at least a
1500 psi
(10 MPa, 102 bar)
maximum working pressure
and
those to the pump fluid outlet side must have at
least a
375 psi (2.6 MPa, 26 bar)
maximum
working pressure.
WARNING
6 308-390
Installation
Pump Accessories
Suction
Hose Kit, Part No. 236–054
A suction tube kit is available for siphoning from
55-gallon containers.
Intake T
ube
(not shown)
T
o install, apply
tape to the female threads at
the top of the tube. Screw the tube tightly onto the
intake housing of the stubby pump.
Low-level Cutoff V
alve, Part No. 203–688
T
o install, screw the low-level cutoff valve into the
bottom of the pump intake tube or the suction tube.
This valve closes the pump intake when the fluid level
is low
, causing the pump to stall to avoid running dry
.
Ground W
ire, Part No. 222–01
1
A ground wire is required.
Pump Outlet Drain V
alve
, Part No. 210–658
Install a drain valve (D) close to the pump fluid outlet to
assist in relieving fluid pressure in the pump when the
pump is shut of
f. See warning below
.
Pump Outlet Drain V
alve
A pump outlet drain valve (D) is required in your
system. This valve helps relieve pressure in the
displacement pump and hose when shutting down
the system and in case of a clogged outlet hose.
Install the valve close to the pump outlet.
WARNING
Keep The Hydraulic System Clean
The hydraulic supply system must be kept clean
at all times to reduce the risk of damaging the
reciprocator hydraulic power supply
. Blow out all
hydraulic lines with air, flush thoroughly with sol
-
vent, and then blow out with air again before con
-
necting the lines to the reciprocator
.
Always plug the hydraulic inlets, outlets and lines
when disconnecting them for any reason to avoid
introducing dirt and other contaminants into the
system.
Carefully follow the manufacturer
’
s recommenda
-
tions on reservoir and filter cleaning, and periodic
changes of hydraulic fluid.
CAUTION
Hydraulic Power Supply
Limit Fluid Flow to Reciprocator
T
o reduce the risk of overpressurizing the hydraulic
reciprocator
, which could cause a rupture and
serious injury
, including fluid injection, the hydraulic
system must have a means to limit the incoming
fluid flow to the reciprocator to a maximum of 3
gpm (1
1 lpm) and 1500 psi (10 MPa, 102 bar). See
the description below
.
WARNING
The hydraulic power supply system must have a
pressure reducing valve and a pressure-compensated
flow control. A flow control valve (N) is required to limit
the incoming flow to the reciprocator to a
maximum of
3 gpm (1
1 lpm)
.
NOTE:
A supply line shut-of
f valve (K), pressure
gauge (L), pressure reducing valve (M), and flow
control valve (N) are included in the Hydraulic Fluid
Control Kit 236–864, which can be ordered separately
.
PTFE
7308-390
Installation
Hydraulic Lines
NOTE: Refer
to Fig. 1 to locate the parts mentioned
below.
DShut-off valves (H and K)
are installed in the
hydraulic supply and return lines. Order Part No.
108–458 for 1/2 npt(f) supply lines and 108–537 for
3/4 npt(f) return lines.
D
Drain Line. Remove the plug (B) from the pump
adapter
, and install a 1/8–27 npt(f) tube fitting and
weep tube, ending in a waste container
. Monitor the
weepage of hydraulic fluid. If it seems excessive or
increases suddenly
, the reciprocator/pump seals
may need to be changed. See page 1
1.
DHoses.
Use a minimum 1/2” supply line (P) and
minimum 3/4” return line (F) on the reciprocator
.
Contact your Graco representative for details of line
sizing.
D
A pressure reducing valve (M)
circulates excess
hydraulic fluid pressure back to the hydraulic power
supply
. Install this valve in the hydraulic supply line
(P) with a drain hose teed into the hydraulic return
line (F). Limit supply pressure to a maximum of
1500 psi (10 MPa, 102 bar).
D
A fluid-filled pressure gauge (L), Part No.
112–567,
monitors hydraulic pressure to the
reciprocator during startup. Use the gauge for
initial adjustment of the reciprocator
. It can be
removed after adjustment is made.
NOTE:
A supply line shut-of
f valve (K), pressure
gauge (L), pressure reducing valve (M), and flow
control valve (N) are included in the Hydraulic Fluid
Control Kit 236–864, which can be ordered separately
.
Grounding
To
reduce the risk of static sparking, ground the pump.
Check your local electrical code for detailed grounding
instructions for your area and type of equipment.
D
Pump:
Use ground wire and clamp as shown in
Fig. 2. T
o order a Grounding Wire and Clamp Kit,
order Part No. 222–01
1.
D
Hydraulic Hoses and Fluid Outlet Hoses:
Use only
electrically conductive hoses.
D
Hydraulic Power Supply:
Follow manufacturer
’s
recommendations.
D
Any pails used when flushing:
Use only metal,
grounded pails when flushing. Make firm
metal-to-metal contact between the a metal part of
the dispense valve and the pail. Use the lowest
possible pressure.
To ground the pump,
loosen the grounding lug
locknut (W) and washer (X). Insert one end of a 12 ga
(1.5 mm @
) minimum ground wire (Y) into the slot in lug
(Z), and tighten the locknut securely
. Connect the other
end of the wire to a true earth ground. See Fig. 2.
Fig. 2
ZX W
Y
03517
Operation
Pressure Relief Procedure
INJECTION
HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or dispensing accidentally
. Fluid
under high pressure can be injected through the
skin and cause serious injury
. T
o reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the
Pressure Relief Procedure
whenever you
D
Are instructed to relieve the pressure
D
Check or service any of the system equipment
D
Install or clean the nozzle
WARNING
1.
Shut of
f the hydraulic power supply
.
2.
Close the supply line shut-of
f valve (K in Fig. 1).
3.
Open the dispensing valve to relieve pressure.
4.
Open the pump outlet drain valve, and have a
container ready to catch the drainage.
5.
Close the return line shut-of
f valve (H).
NOTE:
Leave the drain valve open until you are ready
to dispense again.
If you suspect that the nozzle or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above,
very slowly loosen the
hose end coupling to relieve pressure, then clear the
obstruction.
Be sure you
always
shut of
f the hydraulic supply
line shutof
f valve (K) before you close the return
line shutof
f valve (H). This is to prevent overpres
-
surizing the motor or its seals. When starting up
the hydraulic system, open the return line shutof
f
valve first.
WARNING
Before
Y
ou Start The Pump
Recommended
Hydraulic Oil
Use Graco-approved Hydraulic Oil or a premium,
ISO grade 46 petroleum-based hydraulic oil con
-
taining rust and oxidation inhibitors and anti-wear
agents.
Before using any other type of oil in this motor
,
contact your Graco distributor
. Unauthorized use of
lesser grade oil or substitutes may void the war
-
ranty.
Hydraulic Oil W
orking Temperature
The recommended hydraulic oil operating tempera
-
ture is 80 to 1
15_
F (27 to 45
_ C). The motor
seals will wear faster and leakage may occur if the
pump is operated at higher oil temperatures.
If the hydraulic oil temperature approaches 130
_ F
(54_
C), check the hydraulic fluid supply cooling
system, filters, etc. and clean or repair as needed.
CAUTION
1.
Check the hydraulic fluid level in the hydraulic
power supply
before each use
,
and add fluid as
necessary to fill the lines.
2.
Flush the pump before using it for the first time
to
remove the light oil which was left in after factory
testing to protect the pump from corrosion. Be sure
the solvent used is compatible with the fluid to be
pumped and the pump wetted parts. See
T
echnical Data
on page 23. Flush until clean
solvent comes from the outlet hose.
Operation
Starting the Pump
Maximum
W
orking Pressures
T
o reduce the risk of serious bodily injury
includ-
ing fluid injection and splashing in the eyes or on
the skin, which may be caused if a component
ruptures:
Never exceed
1500 psi (10 MPa, 102 bar) Maxi
-
mum Hydraulic Pressure
to the reciprocator
.
Never exceed
375 psi (2.6 MPa, 26 bar) Maxi
-
mum Outlet Pressure
from the displacement
pump.
Be sure all accessories added to the reciproca
-
tor power supply side are capable of at least a
1500 psi (10 MPa, 102 bar) maximum working
pressure and all of those for the pump fluid out
-
let side have at least a 375 psi (2.6 MPa, 26 bar)
maximum working pressure
.
The maximum working pressure of the displace
-
ment pump is directly proportional to the pres
-
sure at which the reciprocator is operated.
Therefore, if the fluid supplied to the reciprocator
is 1000 psi (7 MPa, 69 bar), the pump fluid out
-
let pressure will be 250 psi (1.8 Mpa, 18 bar).
WARNING
1. T
urn on the hydraulic power supply
.
2.
Open the return line shutof
f valve (H), and slowly
open the hydraulic supply line shutoff valve (K).
3.
Adjust the flow control valve (N) to limit the
hydraulic flow to no more than 3 gpm (1
1 lpm),
which is approximately 60 cycles per minute.
NOTE:
If Graco Part No. 236–864 hydraulic fluid
control is used, no adjustment is necessary
.
4.
By adjusting the pressure reducing valve control
adjustment (M), increase the hydraulic inlet
pressure from 500 to 1500 psi (3.4 to 10 MPa, 34
to 102 bar). Increasing the inlet pressure
increases the outlet pressure. Decreasing the inlet
pressure decreases the outlet pressure.
5.
Always use the lowest pressure possible to obtain
the desired results. This reduces pump wear
.
Never allow a pump to run dry of the fluid being
pumped. A dry pump quickly speeds up and can
damage itself. If it speeds up, shut of
f the power
supply to the reciprocator immediately
. Refill the
supply container
, and prime the pump to eliminate
air.
T
o prevent the pump from running dry
, use a low-
level cutoff valve.
CAUTION
If the Reciprocator Leaks at the Fluid
Fittings
Tighten
the fittings (16, 17, 25), which are self-sealing
and have replaceable o-rings. If leaking persists,
change the o-rings. See Fig. 3.
Fig. 3
SELF-SEALING
FIT
-
TING
(16, 17, 25)
O-RING
RECIPROCATOR
03522
Shutdown
Relieve
the pressure
whenever you shut down.
WARNING
T
o reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure
on page 8.
10 308-390
Troubleshooting
WARNING
T
o reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure
on page 8.
Note:
Check all possible problems and solutions
before disassembling the pump or reciprocator
.
PROBLEM CAUSE SOLUTION
Pump will not run.
Closed dispense valve.
Pump only runs with valve open.
Pressure too low
.Increase supply pressure using the
pressure
adjusting valve.
Insuf
ficient hydraulic fluid supply
.Check hydraulic supply . Adjust to a
maximum
of 3 gpm (1
1 lpm) flow
.
Clogged fluid outlet line, intake
valve,
dispense valve, suction line.
Relieve pressure. Check; clear
obstructions.
Reciprocator damaged.
Repair
. See page 14 or 17.
Pump
speeds up or runs erratically
. Pump
piston and/or intake
valve worn.
Relieve pressure. Check and repair .
See
page 18.
Empty supply container
. Refill
and reprime. Do not allow pump
to
run dry
. Monitor closely or use a low-
level
cutof
f valve.
Pump runs, but output low on up
and/or
down stroke.
Pump piston and/or intake valve
worn.
Relieve pressure. Check and repair .
See
page 18.
Pump runs but output low on both
strokes.
Insufficient
hydraulic fluid supply
.
Check hydraulic supply
.
Pressure too low
.Increase supply pressure using the
pressure
adjustment on the control.
Clogged fluid outlet line, intake
valve,
dispense valve, suction line.
Relieve pressure. Check; clear
obstructions.
Excessive weepage from porous
plug
(B).
W
orn throat seals..
Repair
. See page 12.
Hydraulic
oil leaks from fittings in the
upper or lower reciprocator blocks
(53, 47).
Fittings
(16,17,25) are loose, or their
o-rings
are worn or damaged.
Tighten
the self-sealing fittings. If
leak
-
ing
persists, change the o-rings.
Other manuals for Dyna-Star 236753
1
This manual suits for next models
1
Table of contents
Other Graco Water Pump manuals
Graco
Graco 24B322 Operating instructions
Graco
Graco E-Flo DCi User manual
Graco
Graco Series B Operation manual
Graco
Graco Dura-Flo 2400 User manual
Graco
Graco G3-G-12NC-2L0000-00C00000 User manual
Graco
Graco Bulldog 221-104 Operation manual
Graco
Graco SaniForce FW1111 User manual
Graco
Graco saniforce 2150 Manual
Graco
Graco Twistork Helix 308345T Parts list manual
Graco
Graco Series A Operation manual
Graco
Graco Fire-Ball 300 User manual
Graco
Graco Husky 3300e Use and care manual
Graco
Graco SaniForce 2150e Instruction Manual
Graco
Graco saniforce 2150 User manual
Graco
Graco G3 Pro User manual
Graco
Graco G-JR Operation manual
Graco
Graco President A Series Operation manual
Graco
Graco FIRE-BALL User manual
Graco
Graco husky 3275 User manual
Graco
Graco 12 VDC EGP User manual
Popular Water Pump manuals by other brands
DUROMAX
DUROMAX XP WX Series user manual
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 operating instructions
Franklin Electric
Franklin Electric IPS Installation & operation manual
Xylem
Xylem e-1532 Series instruction manual
Milton Roy
Milton Roy PRIMEROYAL instruction manual
STA-RITE
STA-RITE ST33APP owner's manual