Graco ST Max 395 Hopper Manual

www.graco.be

ST Max™395

ST Max™II 495/595

SETUP

Connect hose to sprayer and gun.

Tighten hose connections with wrench. Unscrew tip & guard from gun.

Fill throat packing nut with TSL™

to prevent premature packing wear.

Make sure power

switch is set to OFF.

Plug electrical cord

into grounded outlet.

Turn prime valve

to Prime position (down).

Place siphon tube in pail

partially filled with water.

Turn pressure control knob

to lowest pressure, and set

power switch to ON.

Increase pressure until

sprayer starts and water

runs out of prime tube.

Let water run out of prime

tube for 15 seconds.

Decrease pressure

until sprayer stops.

Turn prime valve

to Spray position

(horizontal).

Make sure safety

lever of gun is OFF.

Aim gun at inside

wall of water pail

and squeeze trigger.

Increase pressure until

sprayer starts. Keep gun

triggered into water pail for

1 minute. Release trigger.

Turn prime

valve to Prime

position (down).

Place siphon tube in paint

pail, but leave drain tube

in water pail.

Aim gun at inside

wall of water pail,

and squeeze trigger.

Transfer drain

tube to paint pail.

Increase pressure until

sprayer starts and paint

comes out of drain tube.

Keeping gun triggered into water

pail, turn prime valve

to Spray position (horizontal).

When paint comes out of gun,

release trigger and turn safety

lever of gun to ON.

Screw tip & guard onto gun, making sure

arrow-shaped handle of tip is pointing forward.

You can reverse this tip to quickly clear clogs

without taking it apart.

This procedure is for water-base paints and flushing fluids. For solvent-base paints and flushing

fluids (i.e. mineral spirits), you must read Fire and Explosion Hazard in the Operating Instructions.

* check the Graco operations manual delivered with the unit for more details.

CHOOSE THE RIGHT TIP & FILTER

WARNING

Quick Operator’s Guide

207

307

109

209

309

409

509

609

111

211

311

411

511

611

113

213

313

413

513

613

115

215

315

415

515

615

815

217

317

417

517

617

817

917

119

219

319

419

519

619

819

121

221

321

421

521

621

721

821

223

323

423

523

623

723

225

325

425

525

625

725

327

427

527

627

827

429

529

629

729

331

531

631

831

433

533

633

833

235

435

535

635

735

835

935

439 443

543

645

451

551

455

555

655

5 cm

10 cm

15 cm

20 cm

25 cm

30 cm

35 cm

40 cm

45 cm

3 cm

7 cm

10 cm

15 cm

20 cm

25 cm

30 cm

35 cm

40 cm

pump ﬁlter

gun ﬁlter

200 mesh

100 mesh

60 mesh

none

30 mesh

* at 30 cm spraying distance

Ink

Stains

Lacquers

Enamels

Urethanes

Acrylics

Emulsions

Latex

Block ﬁller

Intumescents

Texture material

for spray applications 1st digit X5

=fan width*

Time to

change!

NEW WORN

SPRAYING

Turn safety lever

of gun to OFF.

Point gun at area to be sprayed about 30 cm from surface, and begin moving gun before triggering. A good spray pattern is evenly

distributed as it hits surface. Set pressure just high enough to spray without heavy edges. Use smaller tip size for thinner material

and a larger tip size for thicker material if pressure adjustment cannot achieve even spray pattern.

SHUTDOWN AND CLEANUP

Set power

switch to OFF.

Trigger gun

until pressure

is relieved.

Turn prime valve

to Prime position (down).

Remove gun

filter assembly.

Unscrew tip & guard from

gun. Clean gun filter, inlet

screen, tip, guard and

manifold filter with water

and brush.

Set power switch to ON,

and increase pressure

until sprayer starts.

As soon as Pump Armor

comes out of drain tube,

set power switch to OFF.

Screw inlet screen onto

siphon tube, replace

manifold filter and spacer,

and assemble gun with

filter, tip and guard.

Wipe outside of sprayer,

hose and gun with rag

soaked in water or

mineral spirits.

Fill throat packing

nut with TSL.™

Place drain tube

and siphon tube

in pail of water.

Turn pressure control knob to

lowest setting, set power switch

to ON, and increase pressure until

sprayer starts. Let sprayer run and

flush itself for 2 minutes.

Keeping gun triggered

into water pail, turn prime

valve to Spray position

(horizontal).

Set power switch to OFF, turn

pressure control knob to lowest

setting, and turn prime valve to

Prime position (down).

Place drain tube in waste

pail and siphon tube in

container of Pump Armor™

Assemble gun

without filter.

Unscrew inlet screen

from siphon tube.

WASTE

Keep gun triggered

into pail for 1 minute,

until water coming out

of gun is clean.

Remove manifold

filter and spacer.

GRACO N.V. Industrieterrein Oude Bunders

Slakweidestraat 31 • B-3630 Maasmechelen

Tel: +32 (89) 770 700 • Fax: +32 (89) 770 777

E-mail: [email protected] • http://www.graco.be

All information, illustrations, and specifications in this document are based on the latest product information

available at the time of publication. The right is reserved to make changes at any time without notice.

Graco is certified ISO 9001.

Other manuals for ST Max 395 Hopper

This manual suits for next models

Other Graco Paint Sprayer manuals

Graco

Graco LineLazer IV Series User manual

Graco

Graco GX series Guide

Graco

Graco Series A Operation manual

Graco

Graco Contractor 288477 Operation manual

Graco

Graco HydroShield WMBH00 Parts list manual

Graco

Graco AA 2000 Operation manual

Graco

Graco Series A Operation manual

Graco

Graco RTX2500 Guide

Graco

Graco ULTRA 600 231-307 Series A Operation manual

Graco

Graco T-Max Applicator 256383 Use and care manual

Graco

Graco Pro Xp H60T10 User manual

Graco

Graco dutymax gh 300 Operating instructions

Graco

Graco Mark X User manual

Graco

Graco XM Series Use and care manual

Graco

Graco FinishPro 256845 User manual

Graco

Graco XPs-hf Series Use and care manual

Graco

Graco SaniForce 26C799 User manual

Graco

Graco EcoQuip 2 EQs User manual

Graco

Graco 25M480 User manual

Graco

Graco FinishPro II 395 User manual

Graco

Graco Xtreme 309329 User manual

Graco

Graco 246483 Operation manual

Graco

Graco Reactor A-20 Instruction Manual

Graco

Graco ASM Zip-Spray 2300 Plus Operating instructions

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual