Graco MAGNUM User manual

SETUP

START UP – FLUSHING

Connect hose to gun. Remove

red cap, connect hose to sprayer.

Securely tighten.

Read Owner’s Manual for complete

instructions and warnings.

This quick guide is not a substitute for reading

and understanding all instruction manuals and

warning labels supplied with the equipment.

Manuals are available at magnum.graco.com

Follow pressure

relief procedure and wear

protective equipment

including but not limited to

protective eye wear.

SKIN INJECTION

HAZARD: Keep clear

of spray tip and leaks.

Engage trigger lock

when not spraying.

FIRE AND EXPLOSION

HAZARD: Follow

ﬁre and explosion

warnings as listed in

your manual.

Turn Power Switch

OFF

and plug

sprayer into grounded outlet.

Turn gun trigger lock to locked

position. Unthread spray tip

and guard assembly.

Separate small, clear drain tube

from large suction tube and place

into waste pail.

Turn Pressure Control Knob

to lowest setting.

Allow ﬂuid to ﬂow out drain tube

for 30-60 seconds. Turn Power

Switch

OFF

With the Prime/Spray Valve down to

PRIME

, press PushPrime™button twice,

turn Pressure Control Knob to Prime/Clean setting. Turn Power Switch

QUICK GUIDE

Submerge suction tube in water

if spraying water-based material

or ﬂushing ﬂuid if spraying

oil-based.

FAILURE TO FOLLOW ALL WARNINGS CAN RESULT IN SERIOUS INJURY, AMPUTATION, OR DEATH.

START UP – FILL PUMP, GUN & HOSE WITH PAINT

Trigger gun into waste pail, turn Prime/Spray Valve forward to

SPRAY

and turn Power Switch

When paint comes out of the gun, release trigger. Turn gun trigger lock to locked position. Thread spray tip and

guard assembly to gun.

Attach drain tube to suction tube and turn Pressure Control Knob to Spray Setting. Start at lowest

setting and increase until pattern is evenly distributed, no gaps at edge.

YOU ARE NOW READY TO SPRAY!

Submerge suction tube in paint. Turn Power Switch

and wait to see paint coming into the drain tube.

Turn Power Switch

OFF

1500 psi

103 bar/10.3 MPa

3000 psi

207 bar/20.7 MPa

Good

spray pattern

tails- gaps at edges

pressure

too low

CLEAN UP: WATER-BASED PAINTS (see Owner’s Manual for oil-based paints)

Turn Power Switch

OFF

. Place suction and drain tubes in waste pail. Turn Prime/Spray Valve down to

PRIME

Turn Pressure Control Knob to Prime/Clean setting. Trigger gun into waste pail.

Unscrew inlet strainer from suction tube and place

in waste pail for cleaning. Thread Power Flush

attachment to suction tube. Turn Power Switch

and let water run through drain tube for

20 seconds. Turn Power Switch

OFF

Turn Pressure Control Knob to lowest setting and release

trigger. Turn gun trigger lock to locked position. Turn Prime/

Spray Valve down to

PRIME

. Turn Power Switch

OFF

With the trigger lock in locked position, unthread spray tip and

guard assembly from gun. Place in waste pail for further cleaning.

TO SAVE PAINT IN HOSE

: Trigger gun into paint pail,

turn Prime/Spray Valve forward to

SPRAY

and turn Power

Switch

. When water comes out of gun, keep gun

triggered and aim into waste pail. Continue to ﬂush until

water runs clear.

Clean spray tip, guard, inlet strainer with

brush. Remove gun ﬁlter and clean.

Reassemble gun ﬁlter, spray tip and guard.

Thread Power Flush™attachment onto

garden hose, turn water on. Rinse paint

off of suction and drain tubes,

inlet screen and spray tip/guard.

STORAGE FLUID

Remove Power Flush attachment from suction tube.

Submerge suction tube in Pump Armor.™Turn Prime/Spray Valve down to

PRIME

. Turn Power

Switch

. Turn Pressure Control Knob to Prime/Clean

setting.

When Pump Armor comes out of drain tube,

turn Pressure Control Knob to lowest setting

and Power Switch

OFF

Turn Prime/Spray Valve to

SPRAY

and install inlet

strainer on suction tube for storage.

Every Graco purchase comes

with A+ Customer Service.

Questions?

(888)541-9788

magnum.graco.com/aplus

magnum.graco.com/magop

3A3526 Revision B, May 2016. Original Instructions.This Quick Guide contains English.

Scan QR code for

Operational Video

Other Graco Paint Sprayer manuals

Graco

Graco DutyMax DH230 HD Guide

Graco

Graco FLEX A Series Operation manual

Graco

Graco Spray Station User manual

Graco

Graco PRO 309292S User manual

Graco

Graco 204355 K Series Operation manual

Graco

Graco 288629 User manual

Graco

Graco Series B Operation manual

Graco

Graco Series B Operation manual

Graco

Graco GTS-2500 B Series Operation manual

Graco

Graco e-Xtreme Driver User manual

Graco

Graco 311322L Quick start guide

Graco

Graco 232900 User manual

Graco

Graco HydroShield WMBH00 Parts list manual

Graco

Graco AIRPRO 312414D Operation manual

Graco

Graco Gusmer H-20/35 Pro User manual

Graco

Graco 237-296 Operation manual

Graco

Graco PROX19 User manual

Graco

Graco EH 333 HYDRA-SPRAY A Series Operation manual

Graco

Graco Reactor 2 Instruction Manual

Graco

Graco Xtreme XL 45 Parts list manual

Graco

Graco 24S134 Guide

Graco

Graco 231-817 Operation manual

Graco

Graco Nova spx User manual

Graco

Graco Pro/Delta Spray 240367 Operation manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual