Graco LineLazer II 3900 User manual

308874

Rev. B

First choice when

quality counts.

Model 232651

Related Manuals

Operation 308873. . . . . . . . . . . . . . . . . . . . . . . . . .

Displacement Pump 308798. . . . . . . . . . . . . . . . .

Spray Gun 308235. . . . . . . . . . . . . . . . . . . . . . . . .

Spray Tip *. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PC Board 308919. . . . . . . . . . . . . . . . . . . . . . . . . .

Drain Valve Kit 308961. . . . . . . . . . . . . . . . . . . . . .

* for spray tip selection see page 4.

All models are not available in all countries

PATENTS PENDING

8824A

INSTRUCTIONS-REPAIR

INSTRUCTIONS

KEEP FOR REFERENCE.

Read this and all related manuals for

important warnings and instructions.

LineLazer II 3900 and 5900

3300 psi (230 bar, 23 MPa ) Maximum Working Pressure



Model Series Description

232651 AComplete Sprayer

232652 AComplete Sprayer with 2nd Gun Kit



Model Series Description

232661 AComplete Sprayer

232662 AComplete Sprayer with 2nd Gun Kit

Table of Contents

Component Identification and Function 3. . . . . . . . . . . .

Spray Tip Selection Guide 4. . . . . . . . . . . . . . . . . . . . . . .

Maintenance 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Repair

Bearing Housing & Connecting Rod 8. . . . . . . . . . . . .

Drive Housing 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pinion Assembly/Rotor/Field/Shaft/Clutch 10. . . . . . .

Clamp 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Clutch Housing 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pressure Control 14. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Displacement Pump 16. . . . . . . . . . . . . . . . . . . . . . . . .

Parts

Model 232651, 232661 LineLazer II 17. . . . . . . . . . . .

Pinion Assembly 23. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Complete Sprayers 26. . . . . . . . . . . . . . . . . . . . . . . . . .

Pressure Control 25. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dimensions 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Data 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Phone Number 27. . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Warranty 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

Graco Inc. is registered to I.S. EN ISO 9001



Warnings and Cautions

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

Fluid injection is a serious injury! If high pressure fluid pierces

your skin, the injury might look like “just a cut”. But it is a serious

wound! Get immediate medical attention.

To help prevent injection, always:

Engage trigger safety latch when not spraying.

Point gun away from yourself or anyone else.

Relieve pressure before checking or repairing any leak.

Relieve pressure when you turn off the sprayer or stop spraying.

Do not use components rated less than system

Maximum

Working Pressure

When flushing, ground equipment to grounded object with orange

wire clamp.

Do not flush equipment on asphalt or other non–conductive

surfaces.

Never allow children to use this unit. If you are injured using this

equipment, get immediate medical treatment.

Fire and explosion can occur when spraying or flushing flammable

fluid in an area where air circulation is poor and flammable vapors

can be ignited by an open flame or sparks.

To help prevent a fire and explosion:

Use outdoors or in an extremely well ventilated area.

Do not use 1,1,1–trichloroethane, methylene chloride, other

halogenated hydrocarbon solvents or fluids containing such

solvents in pressurized aluminum equipment. Such use could

result in a chemical reaction, with the possibility of explosion.

Remove, extinguish or unplug all ignition sources;

tape wall switch. Do not smoke in spray area.

Never fill fuel tank while the engine is running or hot.

Ground Sprayer, object being sprayed, paint and solvent pails.

Hold gun firmly to side of a grounded pail when triggering into pail.

Use only conductive airless paint hose.

Never run engine in inclosed area.

Do not flush with gasoline.

WARNING

 

Component Identification and Function

8825A

Fig. 1

Model 232651

ENGINE SPEED ENGINE STOP

TIP SIZE

APressure Control Switch ON/OFF, enables/disables clutch function

BPressure Adjusting Knob Controls fluid outlet pressure

CAir Cleaner* Filters air entering the carburetor

DFuel Tank* Uses 86 octane gasoline

EMuffler* Reduces noise of internal combustion

FSpark Plug Cable* Routes electrical current to spark plug

GFuel Shutoff Lever* On/off lever to regulate fuel flow from gasoline tank to carburetor

HChoke* Enriches air/gasoline mixture for cold starting

JThrottle Lever* Adjusts engine speed for large or small orifice spray tips

KEngine Switch* Enables/disables engine operation

LSecondary Fluid Outlet Second hose and spray gun is connected here

MPressure Control Controls clutch cycling to maintain fluid pressure

NPrimary Fluid Outlet Hose and spray gun is connected here

PEngine* 4–cycle gasoline engine

RClutch Housing Transfers power from engine to drive assembly

SDrive Housing Transfers power from clutch to displacement pump

TDisplacement Pump Provides fluid to be sprayed through spray gun

UFluid Filter Filters fluid between source and spray gun

VGrounding Clamp and Wire Grounds sprayer system

WPressure Drain Valve Relieves fluid pressure when open

*For more detailed explanations of these controls, refer to the Honda Engines Owner ’s Manual; supplied

1. Install the spray tip in the gun. Sprayer is supplied with tip LLT319. For additional applications, use the tip

selection table as follows:



Spay Tip Selection Guide

LineLazer Tip Selection Guide. Sprayer is supplied with tip LLT319. For additional applications, use the tip selec-

tion table as follows:

Note: the last three digits (LLT319) of the tip part number identifies the line width and tip orifice (opening) in millimeters.

For example: the line width for tip LLT319 is 4 in. as shown in the table below. The tip orifice for tip LLT319 is 19 mm.

LineLazer Tip Selection Table

Tip Size Line Width Used For

221211* 2 inches Sport court – light film build

LLT213* 2 inches Sport court – heavy film build

LLT215* 4 inches Alkyd paints only – light film build

LLT217 4 inches Alkyd paints only – medium film build

LLT219 4 inches Alkyd paints only – heavy film build

LLT315 4 inches Most traffic paints – light film build

LLT317 4 inches Most traffic paints – medium film build

LLT319 4 inches Most traffic paints – medium film build

LLT321 4 inches Most traffic paints – heavy film build

LLT323 4 inches Most traffic paints – heavy film build

LLT417# 4 – 8 inches All paints and high solids traffic paints – light film build

LLT419# 4 – 8 inches All paints and high solids traffic paints – medium film build

LLT421# 4 – 8 inches All paints and high solids traffic paints – heavy film build

LLT621 8 – 12 inches All traffic paints – light film build

LLT623 8 – 12 inches All traffic paints – medium film build

LLT625 8 – 12 inches All traffic paints – medium film build

LLT627 8 – 12 inches All traffic paints – heavy film build

* May require 100 mesh filter to minimize tip plugging.

# Best for cold weather applications.

How to Maximize Line Quality and Reduce T ip Wear. Observe the following suggestions to increase line quality

and minimize sprayer tip wear.

1. Select a larger tip orifice and run the sprayer at a reduced operating pressure.

2. Running larger tip sizes (example: use tip LLT321 @ 2000 psi instead of LLT317 @ 3300 psi) will significantly

increase tip life and reduce tip plugging. It will also produce a more uniform film build across the line.

 

Maintenance

WARNING

INJECTION HAZARD

The system pressure must be manually

relieved to prevent the system from

starting or spraying accidentally. Fluid

under high pressure can be injected through the

skin and cause serious injury. To reduce the risk of

an injury from injection, splashing fluid, or moving

parts, follow the Pressure Relief Procedure

whenever you:

are instructed to relieve the pressure,

stop spraying,

check or service any of the system equipment,

or install or clean the spray tip.

Pressure Relief Procedure

1. Lock gun trigger safety.

2. Turn engine ON/OFF switch to OFF.

3. Move pressure control switch to OFF and turn

pressure control knob fully counterclockwise.

4. Unlock trigger safety. Hold metal part of gun firmly

to side of grounded metal pail, and trigger gun to

relieve pressure.

5. Lock gun trigger safety.

6. Open pressure drain valve. Leave valve open until

ready to spray again.

7. Disconnect spark plug cable.

If you suspect that the spray tip or hose is completely

clogged, or that pressure has not been fully relieved

after following the steps above,

VERY SLOWLY

loosen tip guard retaining nut or hose end coupling to

relieve pressure gradually, then loosen completely.

Now clear tip or hose.

CAUTION

For detailed engine maintenance and specifications,

refer to separate Honda Engines Owner’s Manual,

supplied.

DAILY: Check engine oil level and fill as necessary.

DAILY: Check hose for wear and damage.

DAILY: Check gun safety for proper operation.

DAILY: Check pressure drain valve for proper opera-

tion.

DAILY: Check and fill the gas tank.

AFTER THE FIRST 20 HOURS OF OPERA TION:

Drain the oil and refill with clean oil.

WEEKLY: Remove air filter cover and clean element.

Replace element, if necessary. If operating in an

unusually dusty environment: check filter daily and

replace, if necessary.

Replacement elements can be purchased from your

local HONDA dealer.

WEEKLY: Check level of TSL in displacement pump

packing nut. Fill nut, if necessary. Keep TSL in nut to

help prevent fluid buildup on piston rod and premature

wear of packings.

AFTER EACH 100 HOURS OF OPERATION:

Change oil.

MONTHLY: Oil connecting rod.

SPARK PLUG: Use only BPR6ES (NGK) or

W20EPR–U (NIPPONDENSO) plug. Gap plug to

0.028 to 0.031 in. (0.7 to 0.8 mm). Use spark plug

wrench when installing and removing plug.



Troubleshooting

WARNING

INJECTION HAZARD

To reduce risk of serious injury, including fluid injection or splashing in eyes or on skin, or injury from

moving parts, always follow Pressure Relief Procedure Warning, page 5, before checking, adjust-

ing, cleaning or shutting down sprayer.

Disconnect spark plug!

Check everything in chart before disassembling sprayer.

PROBLEM CAUSE SOLUTION

Engine won’t start Engine switch is OFF Turn engine switch ON

Engine is out of gas Refill gas tank. Honda Engines Owner’s Manual.

Engine oil level is low Try to start engine. Replenish oil, if necessary.

Honda Engines Owner’s Manual.

Spark plug cable is disconnected or damaged Connect spark plug cable or replace spark

plug

Cold engine Use choke

Fuel shutoff lever is OFF Move lever to ON position

Oil is seeping into combustion chamber Remove spark plug. Pull starter rope 3 or 4

times. Clean or replace spark plug. Try to start

engine. Keep sprayer upright to avoid oil seep-

age.

Engine operates, but dis-

lacement

does not

Pressure control switch is OFF. Turn pressure control switch ON.

acement pump

oes not

operate. Pressure setting is too low. Turn pressure adjusting knob clockwise to

increase pressure.

Fluid filter (318) is dirty. Clean filter. See page 25.

Tip or tip filter is clogged. Clean tip or tip filter. See gun instruction

manual.

Displacement pump piston rod is stuck due to

dried paint.

Repair pump. See manual 308798.

Connecting rod is worn or damaged. Replace connecting rod. See page 8.

Drive housing is worn or damaged. Replace drive housing. See page 9.

Electrical power is not energizing field. Check wiring connections. See page 12.

Reference control board diagnostics. Page 15.

 ! # !

! !    

# #!   



"! # 

! # 

 !  # 1.2  0.2Ω

(LL 3900); 1.7  0.2Ω (LL 5900); if not, replace

pinion housing.

Check control board fuse. If blown, replace

with equivalent automotive fuse.

Have pressure control checked by authorized

Graco dealer.

Clutch is worn, damaged, or incorrectly

positioned.

Replace clutch. See page 10.

Pinion assembly is worn or damaged. Repair or replace pinion assembly, see pg 10.

 

PROBLEM CAUSE SOLUTION

Pump output is low on

stroke

Hose inlet screen (27) is clogged. Clean inlet screen.

upstro

Piston ball (25) is not seating. Service piston ball. See manual 308798.

Piston packings are worn or damaged. Replace packings. See manual 308798.

O-ring (17) in displacement pump is worn or

damaged.

Replace o-ring. See manual 308798.

Pump output is low on down-

stroke or on both strokes

Hose strainer (27) is clogged. Clean strainer screen.

stro

e or on

stro

es.

Piston packings are worn or damaged. Replace packings. See manual 308798.

Intake valve ball is not seating properly. Clean intake valve. See manual 308798.

Engine speed is too low. Increase throttle setting. See manual 308873.

Clutch is worn or damaged. Replace clutch. See page 10.

Paint leaks into wetcup. Wetcup is loose. Tighten wetcup just enough to stop leakage.

Throat packings are worn or damaged. Replace packings. See manual 308798.

Displacement rod is worn or damaged. Replace rod. See manual 308798.

Fluid delivery is low. Inlet screen is clogged. Clean inlet screen.

Pressure setting is too low. Increase pressure. See manual 308873.

Engine speed is too low. Increase throttle setting. See manual 308873.

Fluid filter (318), tip filter or tip is clogged or

dirty.

Clean filter. See manual 308873. Or, see gun

instruction manual.

Large pressure drop in hose with heavy

materials.

Use larger diameter hose and/or reduce overall

length of hose. Use of more than 100 ft of 1/4

in. hose significantly reduces performance of

sprayer. Use 3/8 in. hose for optimum perfor-

mance (50 ft minimum).

Fluid is spitting from gun. Air in pump or hose. Check and tighten all fluid connections.

Reprime pump. See manual 308873.

Tip is partially clogged. Clear tip. See gun instruction manual.

Fluid supply is low or empty. Refill fluid supply. Prime pump. See manual

308873. Check fluid supply often to prevent

running pump dry.

Pump is difficult to prime. Air in pump or hose. Check and tighten all fluid connections.

Reduce engine speed and cycle pump as

slowly as possible during priming.

Intake valve is leaking. Clean intake valve. Be sure ball seat is not

nicked or worn and that ball seats well. Reas-

semble valve.

Pump packings are worn. Replace pump packings. See manual 308798.

Paint is too thick. Thin the paint according to the supplier’s

recommendations.

Engine speed is too high. Decrease throttle setting before priming pump.

See manual 308873.

Clutch squeaks each time

clutch engages.

Small irregularities of new clutch surfaces

grind together and cause noise

Clutch surfaces need to wear into each other.

Noise will dissipate after a day of run time.



Bearing Housing and Connecting Rod

NOTE: The item numbers referenced are for the

Hi-Boy models. The Lo-Boy models may have different

item numbers. Use the Hi-Boy item number and part to

find the corresponding Lo-Boy part and item number.

Removal

1. Relieve pressure; page 5.

2. Fig. 3. Remove screws (29) and front cover (86).

3. Unscrew suction tube (27) from pump, hold

wrench on pump intake valve (A) to keep pump

from loosening.

4. Disconnect pump outlet hose (25) from displace-

ment pump outlet nipple (107).

5. Fig. 2. Use screwdriver to push up retaining spring

(83) at top of pump. Push out pin (82).

Fig. 2 

6. Fig. 3. Loosen jam nut (81). Unscrew and remove

displacement pump.

7. Remove four screws (31) and lockwashers (32)

from bearing housing (84).

8. Pull connecting rod (85) and lightly tap lower rear

of bearing housing (84) with plastic mallet to

loosen from drive housing (87). Pull bearing hous-

ing and connecting rod assembly (85) off drive

housing.

9. Inspect crank (B) for excessive wear and replace

parts as needed.

Installation

10. Evenly lubricate inside of bronze bearing (C) in

bearing housing (84), and inside of connecting rod

link (D), with high-quality motor oil (

do not

use

grease

). Liberally pack roller bearing (E) in con-

necting rod assembly (85) with bearing grease.

11. Assemble connecting rod (85) and bearing housing

(84).

12. Clean mating surfaces of bearing and drive hous-

ings.

13. Align connecting rod with crank (B) and carefully

align locating pins (F) in drive housing (87) with

holes in bearing housing (84). Push bearing hous-

ing onto drive housing or tap into place with plastic

mallet.

CAUTION

DO NOT use bearing housing screws (31) to align

or seat bearing housing with drive housing. Align

these parts with locating pins (F), to avoid prema-

ture bearing wear.

14. Install screws (31) and lockwashers (32) on bear-

ing housing. Tighten evenly to 175 in-lb (19 Nm).

15. Refer to Displacement Pump, Installation, page 16.

31,32

107

Pack with bearing grease 114819

Oil

Fig. 3 Model 232651 shown

8796A

LL 3900: Torque to 200 in-lb (22.6 Nm)

LL 5900: Torque to 25 ft-lb (34 Nm)

 

Drive Housing

Removal

1. Relieve pressure; page 5.

2. Fig. 4. Remove bearing housing. Do 1. through 8.

of Bearing Housing and Connecting Rod proce-

dure on page 8.

3. Remove two screws (51) and lockwashers (50).

4. Remove four screws (89) and lockwashers (50)

from pinion housing (88a).

5. Lightly tap around drive housing (87c) to loosen

drive housing. Pull drive housing straight off pinion

housing. Be prepared to support gear cluster (78),

which may also come out.

Installation

1. Liberally apply bearing grease (supplied with

replacement gear cluster) to gear cluster (78). and

to areas called out by note 3. Use full 0.62 pint

(0.29 liter) of grease for LL 3900 and 0.68 pint

(0.32 liter) of grease for LL 5900.

2. Place bronze colored washer (87g) on shaft pro-

truding from large shaft of drive housing(87c).

Place silver colored washer (87h) on pins on pinion

housing. Align gears and push new drive housing

straight onto pinion housing and locating pins (B).

3. Install four screws (89) and lockwashers (50) from

pinion housing (88a).

4. Install two screws (5) and lockwashers (50).

5. Fig. 3. Install bearing housing. Do 10. through 15.

of Bearing Housing and Connecting Rod proce-

dure on page 8.

8698A

Fig. 4

89 50

87h

87g

51 (LL 5900)

87c

88a

77 79

LL 3900 only

Torque to 125 in-lb – LL 3900

Torque to 200 in-lb – LL 5900

Apply remaining grease to these areas

50 (LL 3900)

52 (LL 5900)

51 (LL 3900)



Pinion Assembly/Rotor/Field/Shaft/Clutch

Removal

Fig. 6. If pinion assembly (88a) is attached to clutch

housing (92), do 1. through 4. Otherwise, start at 5.

1. Relieve pressure; page 5.

2. Fig. 5. Disconnect field cable (X) from pressure

control.

Fig. 5



3. Fig. 6. Remove five screws (89/96) and lockwash-

ers (50/51) and pinion assembly (88a).

50 (LL 3900)

Fig. 6 

88a

51 (LL 5900)

89 (LL 3900)

96 (LL 5900)

4. Fig. 7. Place pinion assembly (88a) on bench with

rotor side up.

Fig. 7



5. Remove four screws (52) and lockwashers (50).

Install two screws in threaded holes (E) in rotor.

Alternately tighten screws until rotor comes off.

6. Fig. 8. Remove retaining ring (Z).

7. Tap pinion shaft (A) out with plastic mallet.

Fig. 8



8. Fig.9. Use an impact wrench or wedge something

between clutch and clutch housing to hold clutch

during removal.

9. Remove four screws (50) and lockwashers (53).

10. Remove clutch (91).

Fig. 9



Other manuals for LineLazer II 3900

This manual suits for next models

Table of contents

Other Graco Paint Sprayer manuals

Graco

Graco PRO 247936 User manual

Graco

Graco 223-599 User manual

Graco

Graco Fuller O'brien Paints Pro 501st Series Operation manual

Graco

Graco FTXpress Guide

Graco

Graco TexSpray GTX Owner's manual

Graco

Graco LineLazer 3400 Operating instructions

Graco

Graco 310645K Use and care manual

Graco

Graco Reactor E Series User manual

Graco

Graco SaniSpray HP 65 Use and care manual

Graco

Graco 233001 Operation manual

Graco

Graco 311286C Instruction Manual

Graco

Graco ULTRA MARK X Manual

Graco

Graco 15V823 Parts list manual

Graco

Graco Series E Operation manual

Graco

Graco ULTRA R MAX 695 309067 Operation manual

Graco

Graco 234237 User manual

Graco

Graco 239-139 Operation manual

Graco

Graco M2K Parts list manual

Graco

Graco 295ST 233686 Operating instructions

Graco

Graco SaniSpray HP 20 Use and care manual

Graco

Graco 309489 User manual

Graco

Graco Magnum L10 Operating instructions

Graco

Graco Xtreme 3Z9329L User manual

Graco

Graco Reactor E-20 Series User manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual