Graco GMax 233709 User manual

GMax5900 Convertible

Airless Paint Sprayers 309411E

Related Manuals

Operator 309410. . . . . . . . . . . . . . . . . . . . . . . . . . .

Displacement Pump 309277. . . . . . . . . . . . . . . . .

Spray Gun 309639. . . . . . . . . . . . . . . . . . . . . . . . .

Spray Tip 309640. . . . . . . . . . . . . . . . . . . . . . . . . . .

AutoClean Kit 309450. . . . . . . . . . . . . . . . . . . . . . .

PC Board 309459. . . . . . . . . . . . . . . . . . . . . . . . . .

Electric Motor Kit 309469. . . . . . . . . . . . . . . . . . . .

Drain Valve Kit 308961. . . . . . . . . . . . . . . . . . . . . .

233709

ti1852a

INSTRUCTIONS-PARTS LIST

INSTRUCTIONS

This manual contains important

warnings and information.

READ AND KEEP FOR REFERENCE.

–For Portable Airless Spraying of Architectural Coatings and Paints –

5.5 HORSEPOWER, GASOLINE POWERED

3300 psi (228 bar, 22.8 MPa) Maximum Working Pressure

Model Series Description

233709 ASprayer, gas powered

233710 ASprayer, gas powered, with RACX tip,

gun and hose

233711 ASprayer, gas powered, with electric

motor kit

233712 ASame as 233711 except with ETL

approval to CSA and UL standards

233713 ASprayer, gas powered, with Lo-Boy

suction set kit

233714 ASprayer, gas powered, with RAC X tip,

gun and hose and Lo-Boy suction set kit

233715 ASprayer, gas powered, with Lo-Boy

suction set kit and electric motor kit

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

Graco Inc. is registered to I.S. EN ISO 9001

2309411

Table of Contents

Component Identification and Function 5. . . . . . . . . . . .

Maintenance 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Repair

Bearing Housing and Connecting Rod 9. . . . . . . . . . .

Drive Housing 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pinion Assembly/Rotor/Field/Shaft/Clutch/Pulley 11.

ON/OFF Switch 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pressure Control Repair 14. . . . . . . . . . . . . . . . . . . . . .

Displacement Pump Repair 16. . . . . . . . . . . . . . . . . . .

Parts

Basic Sprayer 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pinion Assembly 21. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pressure Control 22. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wiring Schematic 23. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Clutch Assembly 24. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Complete Sprayer 24. . . . . . . . . . . . . . . . . . . . . . . . . . .

Lo-Boy Suction Set Kit 25. . . . . . . . . . . . . . . . . . . . . . .

Technical Data 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dimensions 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Warranty 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warnings and Cautions

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

The wallet-sized warning card provided with this pole gun should be kept with the operator at all times. The card

contains important treatment information should a fluid injection injury occur. Additional cards are available at no

charge from Graco Inc.

3309411

WARNING

SKIN INJECTION HAZARD

Spray from the spray tip, hose leaks or ruptured components can inject fluid into your body and cause

extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin

can also cause can also cause serious injury.

Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate surgi-

cal treatment!

Do not point the spray tip at anyone or any part of the body.

Do not put hand or fingers over the spray tip, and do not stop or deflect fluid leaks with your hand,

body, glove or rag.

Do not “blow back” fluid; this is not an air spray system.

Always have the tip guard and the trigger guard on the in-line valve when spraying.

Be sure the trigger safety lever operates before operating the in-line valve.

Lock the trigger safety lever when you stop spraying.

Follow the Pressure Relief Procedure on page 6 when you are instructed to relieve pressure;

stop spraying; check, clean, or service any system equipment; or install or change spray tips.

Tighten all fluid connections before each use.

Check the hoses, tubes and couplings daily. Replace worn or damaged parts immediately. Perma-

nently coupled hoses cannot be repaired.

Handle and route hoses and tubes carefully. Keep hoses and tubes away from moving parts and

hot surfaces. Do not use the hoses to pull equipment. Do not expose Graco hoses to temperatures

above 150F (65C) or below –40F (–40C).

TOXIC FLUID HAZARD

Hazardous fluids or toxic fumes can cause a serious injury or death if the fluid is swallowed or

splashed in the eyes or on the skin or if the fumes are inhaled.

Know the specific hazards of the fluid you are using.

Store hazardous fluid in an approved container. Dispose hazardous fluid according to all local,

state and national guidelines.

Dress appropriately for your application. Wear protective eyewear, noise protection for the ears, a

personal respirator, gloves, and clothing.

RECOIL HAZARD

Due to the high pressure fluid emitted, a strong recoil action may occur when you trigger the pole gun.

If you are unprepared, your hand could be forced back toward your body or you could lose your bal-

ance and fall, resulting in serious injury.

4309411

WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and

result in fire or explosion and serious injury.

Ground the equipment and the object being sprayed.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvent or the fluid being

sprayed.

Extinguish all the open flames or pilot lights in the spray area.

Electrically disconnect all the equipment in the spray area.

Keep the spray area free of debris, including solvent, rags, and gasoline.

Do not turn on or off any light switch in the spray area while operating or if fumes are present.

Do not smoke in the spray area.

Do not operate a gasoline engine in the spray area.

If there is any static sparking while using the equipment, stop spraying immediately. Identify and

correct the problem.

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result

in serious injury.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are uncertain about the usage, call your

distributor.

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

Check the equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum working pressure of the lowest rated system component. This equip-

ment has a 3600 psi (25 MPa, 248 bar) maximum working pressure.

Route the hoses away from the traffic areas, sharp edges, moving parts, and hot surfaces. Do not

expose Graco hoses to temperatures above 150F (65C) or below –40F (–40C).

Do not use the hoses to pull the equipment.

Use fluids or solvents that are compatible with the equipment wetted parts. See the Technical

Data section of all the equipment manuals. Read the fluid and solvent manufacturer’s warnings.

Fluid hoses must have spring guards on both ends to protect them from rupture caused by kinks or

bends near the couplings.

Comply with all applicable local, state and national fire, electrical and other safety regulations.

Wear hearing protection when operating this equipment.

HAZARD OF USING FLUIDS CONTAINING HALOGENATED HYDROCARBONS

Never use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids

containing such solvents in this equipment. Such use could result in a serious chemical reaction, with

the possibility of explosion, which could cause death, serious injury and/or substantial property dam-

age.

Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum and zinc

parts.

5309411

Component Identification and Function

Motor On/Off Switch

Prime/Drain Valve

Engine On/Off Switch Pump On/Off Switch

Pressure Control

Engine Controls

Spray Gun Trigger Lock

ti1854a

ti1852a

Reference your Spray Gun Manual

6309411

Maintenance

WARNING

INJECTION HAZARD

System pressure must be manually

relieved to prevent system from starting

or spraying accidentally. Fluid under high

pressure can be injected through skin and cause

serious injury. To reduce risk of injury from injec-

tion, splashing fluid, or moving parts, follow Pres-

sure Relief Procedure whenever you:

are instructed to relieve pressure,

stop spraying,

check or service any system equipment,

or install or clean spray tip.

Pressure Relief Procedure

1. Lock gun safety latch.

2. Turn engine or electric motor ON/OFF switch to

OFF.

3. Unplug power supply cord (electric motor).

4. Move pressure control switch to OFF and turn

pressure control knob fully counterclockwise.

5. Rotate RAC 5 tip, if used, to reverse position.

6. Unlock gun safety latch. Hold metal part of gun

firmly to grounded metal pail. Trigger gun to relieve

pressure.

7. Lock gun safety latch.

8. Open pressure drain valve. Leave pressure drain

valve open until ready to spray again.

If suspected that spray tip or hose is completely

clogged, or that pressure has not been fully relieved

after following steps above, VERY SLOWLY loosen tip

guard retaining nut or hose end coupling to relieve

pressure gradually, then loosen completely. Now clear

tip or hose obstruction.

CAUTION

For detailed engine maintenance and specifications,

refer to separate engine manual, supplied.

DAILY: Check engine oil level and fill as necessary.

Manual 309410.

DAILY: Check that V-belt (60) is centered on pulleys

and is not inverted. Replace if worn or damaged.

DAILY: Check and fill gas tank.

DAILY: Check hoses for wear and damage.

DAILY: Check gun safety for proper operation.

DAILY: Check pressure drain valve for proper opera-

tion.

AFTER THE FIRST 20 HOURS OF OPERATION

AND EACH 100 HOURS THEREAFTER: Change

engine oil.

DAILY: Keep TSL in packing nut to help lubricate

pump packings. One full squirt of TSL is usually

enough.

WEEKLY: Remove cover of air filter (C) and clean

element. Replace element, if necessary. If operating in

an unusually dusty environment, check filter daily and

replace it, if necessary.

Repack connecting rod (22) top needle bearing after

every pump change.

Replacement elements can be purchased from your

local HONDA dealer.

SPARK PLUG: Use only an BPR6ES (NGK) or

W20EPR–U (NIPPONDENSO) plug. Gap plug to

0.028 to 0.031 in. (0.7 to 0.8 mm). Use a spark plug

wrench when installing and removing plug.

7309411

Troubleshooting

Relieve pressure;page 6.

PROBLEM CAUSE SOLUTION

E=XX is displayed Fault condition exists Determine fault correction from table, page 14.

Engine won’t start Engine switch is OFF Turn engine switch on.

Engine is out of gas Refill gas tank. Honda Engines Owner’s Manual.

Engine oil level low Try to start engine. Replenish oil, if necessary.

Honda Engines Owner’s Manual.

Spark plug cable disconnected or

spark plug damaged

Connect spark plug cable or replace spark plug.

Oil seepage into combustion

chamber

Remove spark plug. Pull starter rope 3 or 4 times.

Clean or replace spark plug. Try to start engine.

Keep sprayer upright to avoid oil seepage.

False tripping of WatchDog

system. EMPTY is dis-

played. Pump does not run.

Operating conditions out of WatchDog

parameters

Low pump output; page 8.

Turn pressure down. Contact Graco Technical Ser-

vice to adjust WatchDog parameters.

Operate without WatchDog active; Manual 309410.

Engine operates, but dis-

placement pump doesn

’

Pressure control switch turned OFF Turn on.

placement pump doesn’t Pressure setting too low Increase pressure.

Displacement pump outlet filter dirty Clean filter.

Tip or tip filter clogged Clean tip or tip filter.

Broken drive belt Replace belt.

Displacement pump rod seized by

dry paint

Service pump. See page 16.

Connecting rod worn or damaged Replace. See page 9.

Drive housing worn or damaged Replace. See page 10.

Electrical power is not energizing clutch field Check wiring connections. Page 23.

Reference pressure control repair. Page 14.

Reference wiring diagram. Page 23.

With pump switch ON and pressure turned to

MAXIMUM, use a test light to check for power be-

tween clutch test points on control board.

Remove 7–pin connector from control board and

measure resistance across clutch coil. At 70F,

the resistance must be 1.7 ±0.2Ω; if not, replace

pinion housing.

Have pressure control checked by authorized Gra-

co dealer.

Clutch is worn, damaged, or incorrectly

positioned Replace clutch. Page 11.

Pinion assembly is worn or damaged Repair or replace pinion assembly. Page 11.

8309411

PROBLEM CAUSE SOLUTION

Pump output low Strainer (31) clogged Clean.

Piston ball (25) not seating Service piston ball check. Manual 309277.

Piston packings worn or damaged Replace packings. Manual 309277.

Displacement pump o-ring (227) is damaged Replace o-ring. Manual 309277.

Intake valve ball not seating properly Clean and service. Manual 309277.

Engine speed is too low Increase throttle setting. See Manual 309410.

V–belt slipping Tighten V–belt with tension bar (101). Adjust

bracket until it takes 15 lb of force to lock

tension bar down.

Clutch worn or damaged Replace. See page 11.

Pressure setting is too low Increase pressure. Manual 309410.

Fluid filter (318), tip filter or tip is clogged or

dirty Clean filter. Manual 309410 or 309091.

Large pressure drop in hose with heavy

materials Use larger diameter hose and/or reduce overall

length of hose. Use of more than 100 ft of 1/4

in. hose significantly reduces performance of

sprayer. Use 3/8 in. hose for optimum perfor-

mance (50 ft minimum).

Excessive paint leakage into

throat packing nut

Throat packing nut is loose Remove throat packing nut spacer. Tighten

throat packing nut just enough to stop leakage.

Throat packings worn or damaged Replace packings. Manual 309277.

Displacement rod worn or damaged Replace rod. Manual 309277.

Spitting from gun Air in fluid pump or hose Check and tighten all fluid connections.

Reprime pump. Manual 309410.

Tip partially clogged Clear tip. Manual 309091.

Fluid supply is low or empty Refill and prime pump. See Startup, Manual

309410. Check fluid supply often to prevent

running pump dry.

Pump is difficult to prime Air leak Check and tighten all fluid connections.

Reduce engine speed and cycle pump as

slowly as possible during priming.

Intake valve is leaking Shut off pump and relieve pressure. Disas-

semble and clean intake valve. Be sure ball

seat is not nicked or worn and that ball seats

well. Reassemble.

Worn packings Repack pump. Manual 309277.

Fluid is too thick Thin fluid according to supplier’s recommenda-

tions.

Engine speed is too high Decrease throttle setting before priming pump.

Manual 309410.

Clutch squeaks each time

clutch engages Clutch surfaces are not matched to each other

when new and may cause noise Clutch surfaces need to wear into each other.

Noise will dissipate after a day of run time

High engine speed at no

load

Misadjusted throttle setting Reset throttle to 3700 engine rpm at no load

Worn engine governor Replace or service engine governor

Gallon counter not working Bad sensor, broken or disconnected wire Check connections. Replace sensor or wire.

No display, sprayer operates Display damaged or has bad connection Check connections. Replace display.

9309411

Bearing Housing and Connecting Rod

Removal

1. Relieve pressure;page 6.

2. Stop sprayer at bottom of stroke to get crank (E) in

lowest position. To lower crank manually, remove

spark plug and carefully rotate crank by pulling

starter rope.

3. Fig. 2. Remove front cover (38). Unclip drain hose

(74) from pump. Unscrew pump suction tube (73)

from pump. Disconnect pump hose (167).

4. Push up retaining spring (59). Push pin (58) out

rear.

Fig. 1 7675B

5. Loosen locknut (57). Unscrew displacement

pump (48).

6. Remove four screws and lockwashers (20, 19).

7. Tap lower rear of bearing housing (60) with a

plastic mallet to loosen from drive housing (3). Pull

bearing housing and connecting rod assembly (40)

straight off drive housing.

8. Remove pail hanger (105) and install it on new

bearing housing.

9. Inspect crank (E) for excessive wear and replace

parts as needed.

Installation

1. Evenly lubricate inside of bronze bearing (B) in

bearing housing (60) with high-quality motor oil.

Liberally pack top roller bearing (C), lower bearing

(D) inside connecting rod assembly (40) with

bearing grease 114819.

2. Assemble connecting rod (40) and bearing

housing (60).

3. Clean mating surfaces of bearing and drive hous-

ings (60, 3).

4. Align connecting rod (C) with crank (E) and drive

housing locating pins (3b) with bearing housing

(60) holes. Push bearing housing onto drive hous-

ing or tap into place with plastic mallet.

CAUTION

Do not use bearing housing screws (19) to align or

seat bearing housing; this may cause bearing and

drive housing misalignment and result in premature

bearing wear.

5. Install screws and lockwashers (20, 19). Tighten

screws evenly to 25 ft-lb (34 Nm).

6. Install pump; page 16.

7. Fig. 2. Install remaining parts.

Fig. 2

8697B

20, 19

107

167

Pack with bearing grease 114819

Oil

Torque to 25 ft-lb (34 Nm)

105

10 309411

Drive Housing

Removal

1. Relieve pressure;page 6.

2. Disconnect reed switch (A).

3. Fig. 3. Remove bearing housing. Do Removal of

Bearing Housing and Connecting Rod proce-

dure on page 9.

4. Remove two screws (31) and lockwashers (37).

5. Remove four screws (35) and lockwashers (34)

from pinion housing (4).

6. Lightly tap around drive housing (3) to loosen drive

housing. Pull drive housing straight off pinion

housing (4). Be prepared to support gear cluster

(36) which may also come out.

CAUTION

Do not drop gear cluster (36) when removing drive

housing (3). Gear cluster is easily damaged. Gear

may stay engaged in drive housing or pinion housing.

Installation

1. Liberally apply bearing grease (supplied with re-

placement gear cluster) to gear cluster (36) and to

areas called out by note 2. Use full 0.68 pint (0.32

liter) of grease.

2. Place bronze colored washer (3g) on shaft protrud-

ing from large shaft of drive housing (3). Note: If

replacing a washer with pin holes with a washer

without pin holes, remove guide pins from housing.

Place silver colored washer (3h) on pinion housing.

Assemble washers (61) and (62) onto gear (36).

Align gears and push new drive housing straight

onto pinion housing and locating pins (B).

3. Install four screws (47) and lockwashers (37) to

pinion housing (4) and drive housing (3).

4. Install two screws (31) and lockwashers (37) to

drive housing (3).

5. Fig. 3. Install bearing housing. Do 1. through 6. of

Bearing Housing and Connecting Rod proce-

dure on page 9.

6. Connect reed switch (A).

Ti1889a

3534

Fig. 3

Apply remaining grease to these areas

1Torque to 200 in-lb

61 62

This manual suits for next models

Table of contents

Other Graco Paint Sprayer manuals

Graco

Graco GH 833 249318 Operating instructions

Graco

Graco LineLazer 130HS Manual

Graco

Graco Merkur G10W09 Parts list manual

Graco

Graco 31-817 Operation manual

Graco

Graco ProMix PD User manual

Graco

Graco IronMax V Operating instructions

Graco

Graco DutyMax DH230 HD Guide

Graco

Graco 24P930 User manual

Graco

Graco Hydra-clean 24V616 Parts list manual

Graco

Graco 231-315 Series Operation manual

Graco

Graco BLACK MAX Operation manual

Graco

Graco 231-081 Datasheet

Graco

Graco FinishPro II 395 PC Guide

Graco

Graco GMAX 3400 Instruction Manual

Graco

Graco Reactor 2 H-30 Instruction Manual

Graco

Graco CX-7 User manual

Graco

Graco 311322H Quick start guide

Graco

Graco Series B Operation manual

Graco

Graco Contractor 288477 Operation manual

Graco

Graco Project Painter Plus User manual

Graco

Graco 241284 User manual

Graco

Graco Monark 236-065 User manual

Graco

Graco Series A Parts list manual

Graco

Graco XP35 User manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual