Graco 17C407 Guide

334603E

Operation, Parts

RentalPro 230PC

Electric Airless Sprayer

For professional use only.

Not approved for use in explosive atmospheres or hazardous locations.

For portable airless spraying of architectural paints and coatings.

Model: 17C407

3300 psi (228 bar, 22.8 MPa) Maximum Working Pressure

Important Safety Instructions

Read all warnings and instructions in this manual and related manuals.

Be familiar with the controls and the proper usage of the equipment.

Save these instructions.

Related Manuals

Gun - 3A6285 (Contractor PC) Pump - 334599

Use only genuine Graco replacement parts.

The use of non-Graco replacement parts may void warranty.

ti25193a

Contents

2334603E

Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Extension Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Pails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Startup/Prime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Spray Tip Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Spray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Clear Tip Clog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Digital Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Mechanical/Fluid Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Sprayer Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Sprayer Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Control and Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Control and Filter Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

110474

Certified to CAN/CSA C22.2 No. 68

Conforms to UL 1450

Warnings

334603E 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this

equipment. The exclamation point symbol alerts you to a general warning and the hazard

symbols refer to procedure-specific risks. When these symbols appear in the body of this

manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols

and warnings not covered in this section may appear throughout the body of this manual

where applicable.

GROUNDING

This product must be grounded. In the event of an electrical short circuit, grounding

reduces the risk of electric shock by providing an escape wire for the electric current.

This product is equipped with a cord having a grounding wire with an appropriate

grounding plug. The plug must be plugged into an outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

•Improper installation of the grounding plug is able to result in a risk of electric

shock.

•When repair or replacement of the cord or plug is required, do not connect the

grounding wire to either flat blade terminal.

•The wire with insulation having an outer surface that is green with or without

yellow stripes is the grounding wire.

•Check with a qualified electrician or serviceman when the grounding instructions

are not completely understood, or when in doubt as to whether the product is

properly grounded.

•Do not modify the plug provided; if it does not fit the outlet, have the proper outlet

installed by a qualified electrician.

•This product is for use on a nominal 110V circuit and has a grounding plug similar

to the plug illustrated below.

•Only connect the product to an outlet having the same configuration as the plug.

•Do not use an adapter with this product.

Extension Cords:

•Use only a 3-wire extension cord that has a grounding plug and a grounding

receptacle that accepts the plug on the product.

•Make sure your extension cord is not damaged. If an extension cord is necessary

use 12 AWG (2.5mm2) minimum to carry the current that the product draws.

•An undersized cord results in a drop in line voltage and loss of power and

overheating.

Warnings

4334603E

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or

explode. To help prevent fire and explosion:

•Do not spray flammable or combustible materials near an open flame or sources

of ignition such as cigarettes, motors, and electrical equipment.

•Paint or solvent flowing through the equipment is able to result in static electricity.

Static electricity creates a risk of fire or explosion in the presence of paint or

solvent fumes. All parts of the spray system, including the pump, hose assembly,

spray gun, and objects in and around the spray area shall be properly grounded

to protect against static discharge and sparks. Use Graco conductive or

grounded high-pressure airless paint sprayer hoses.

•Verify that all containers and collection systems are grounded to prevent static

discharge. Do not use pail liners unless they are antistatic or conductive.

•Connect to a grounded outlet and use grounded extensions cords. Do not use

a 3-to-2 adapter.

•Do not use a paint or a solvent containing halogenated hydrocarbons.

•Do not spray flammable or combustible liquids in a confined area.

•Keep spray area well-ventilated. Keep a good supply of fresh air moving through

the area.

•Sprayer generates sparks. Keep pump assembly in a well ventilated area at least

20 feet (6.1 m) from the spray area when spraying, flushing, cleaning, or

servicing. Do not spray pump assembly.

•Do not smoke in the spray area or spray where sparks or flame is present.

•Do not operate light switches, engines, or similar spark producing products in the

spray area.

•Keep area clean and free of paint or solvent containers, rags, and other

flammable materials.

•Know the contents of the paints and solvents being sprayed. Read all Safety

Data Sheets (SDS) and container labels provided with the paints and solvents.

Follow the paint and solvents manufacturer’s safety instructions.

•Fire extinguisher equipment shall be present and working.

Warnings

334603E 5

SKIN INJECTION HAZARD

High-pressure spray is able to inject toxins into the body and cause serious bodily

injury. In the event that injection occurs, get immediate surgical treatment.

•Do not aim the gun at, or spray any person or animal.

•Keep hands and other body parts away from the discharge. For example, do not

try to stop leaks with any part of the body.

•Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.

•Use Graco nozzle tips.

•Use caution when cleaning and changing nozzle tips. In the case where the

nozzle tip clogs while spraying, follow the Pressure Relief Procedure for turning

off the unit and relieving the pressure before removing the nozzle tip to clean.

•Equipment maintains pressure after power is shut off. Do not leave the

equipment energized or under pressure while unattended. Follow the Pressure

Relief Procedure when the equipment is unattended or not in use, and before

servicing, cleaning, or removing parts.

•Check hoses and parts for signs of damage. Replace any damaged hoses or

parts.

•This system is capable of producing 3300 psi. Use Graco replacement parts or

accessories that are rated a minimum of 3300 psi.

•Always engage the trigger lock when not spraying. Verify the trigger lock is

functioning properly.

•Verify that all connections are secure before operating the unit.

•Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with

the controls.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Always wear appropriate gloves, eye protection, and a respirator or mask when

painting.

•Do not operate or spray near children. Keep children away from equipment at all

times.

•Do not overreach or stand on an unstable support. Keep effective footing and

balance at all times.

•Stay alert and watch what you are doing.

•Do not operate the unit when fatigued or under the influence of drugs or alcohol.

•Do not kink or over-bend the hose.

•Do not expose the hose to temperatures or to pressures in excess of those

specified by Graco.

•Do not use the hose as a strength member to pull or lift the equipment.

•Do not spray with a hose shorter than 25 feet.

•Do not alter or modify equipment. Alterations or modifications may void agency

approvals and create safety hazards.

•Make sure all equipment is rated and approved for the environment in which you

are using it.

Warnings

6334603E

ELECTRIC SHOCK HAZARD

This equipment must be grounded.Improper grounding, setup, or usage of the

system can cause electric shock.

•Turn off and disconnect power cord before servicing equipment.

•Connect only to grounded electrical outlets.

•Use only 3-wire extension cords.

•Ensure ground prongs are intact on power and extension cords.

•Do not expose to rain. Store indoors.

PRESSURIZED ALUMINUM PARTS HAZARD

Use of fluids that are incompatible with aluminum in pressurized equipment can

cause serious chemical reaction and equipment rupture. Failure to follow this

warning can result in death, serious injury, or property damage.

•Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated

hydrocarbon solvents or fluids containing such solvents.

•Do not use chlorine bleach.

•Many other fluids may contain chemicals that can react with aluminum. Contact

your material supplier for compatibility.

MOVING PARTS HAZARD

Moving parts can pinch, cut, or amputate fingers and other body parts.

•Keep clear of moving parts.

•Do not operate equipment with protective guards or covers removed.

•Pressurized equipment can start without warning. Before checking, moving, or

servicing equipment, follow the Pressure Relief Procedure and disconnect all

power sources.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on

skin, inhaled, or swallowed.

•Read SDSs to know the specific hazards of the fluids you are using.

•Store hazardous fluid in approved containers, and dispose of it according to

applicable guidelines.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent

serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns.

This protective equipment includes but is not limited to:

•Protective eyewear, and hearing protection.

•Respirators, protective clothing, and gloves as recommended by the fluid and

solvent manufacturer.

CALIFORNIA PROPOSITION 65

This product contains a chemical known to the State of California to cause cancer,

birth defects or other reproductive harm. Wash hands after handling.

Component Identification

334603E 7

Component Identification

A ON/OFF Switch

B Pressure Control

C Display

D Prime Valve

F Tip Guard

G Spray Tip

HGun

J Airless Hose

K Power Cord

L Trigger Lock

M Drain Tube

N Fluid Intake

PPump

R Fluid Outlet

S Hanger

TFilter

U Finger Guard / TSL Fill Point

V Pail Hook

Model/Serial Tag (Not shown, located

on bottom of unit.)

Grounding

8334603E

Grounding

This sprayer includes a ground wire with an

appropriate ground contact.

The plug must be plugged into an outlet that

is properly installed and grounded in

accordance with all local codes and

ordinances.

Do not modify the plug provided; if it does not

fit the outlet, have the proper outlet installed

by a qualified electrician.

Power Requirements

100-120V units require 100-120 VAC,

50/60 Hz, 13A, 1 phase.

Extension Cords

Use an extension cord with an undamaged

ground contact. If an extension cord is

necessary, use a 3-wire, 12 AWG (2.5 mm2)

minimum.

NOTE: Smaller gauge or longer extension

cords may reduce sprayer performance.

Pails

Solvent and oil-based fluids: follow local

code. Use only conductive metal pails,

placed on a grounded surface such as

concrete.

Do not place pail on a non-conductive surface

such as paper or cardboard which interrupts

grounding continuity.

Always ground a metal pail: connect a

ground wire to the pail. Clamp one end to the

pail and the other end to a true earth ground

such as a water pipe.

To maintain ground continuity when

sprayer is flushed or pressure is relieved:

hold metal part of spray gun firmly to the side

of a grounded metal pail then trigger the gun.

The equipment must be grounded to

reduce the risk of static sparking and

electric shock. An electric or static spark

can cause fumes to ignite or explode. An

improper ground can cause electric shock.

A good ground provides an escape wire for

the electric current.

ti24584a

Pressure Relief Procedure

334603E 9

Pressure Relief Procedure

Follow the Pressure Relief

Procedure whenever you see this

symbol.

1. Turn the ON/OFF switch to the OFF

position. Wait 7 seconds for power to

dissipate.

2. Engage the trigger lock.

3. Turn pressure control to lowest setting.

Disengage the trigger lock.

4. Hold a metal part of the gun firmly to a

grounded metal pail. Trigger the gun to

relieve pressure.

5. Engage the trigger lock.

This equipment stays pressurized until

pressure is manually relieved. To help

prevent serious injury from pressurized

fluid, such as skin injection, splashed fluid

and moving parts, follow the Pressure

Relief Procedure whenever sprayer is

stopped and before sprayer is cleaned or

checked, and before equipment is

serviced.

ti24586a

ti24603b

Pressure Relief Procedure

10 334603E

6. Turn prime valve down. Put drain tube

in a pail. Leave prime valve in down

(drain) position until you are ready to

spray again.

7. If you suspect the spray tip or hose is

clogged or that pressure has not been

fully relieved:

a. VERY SLOWLY loosen the tip

guard retaining nut or the hose end

coupling to relieve pressure

gradually.

b. Loosen the nut or coupling

completely.

c. Clear hose or tip obstruction.

Trigger Lock

Always engage the trigger lock when sprayer

is stopped to prevent the gun from being

triggered accidentally by hand or if dropped

or bumped.

ti24607a

This manual suits for next models

Table of contents

Other Graco Paint Sprayer manuals

Graco

Graco Magnum Pro Plus Guide

Graco

Graco SG20 Parts list manual

Graco

Graco Fine Finish HVLP 7.0 Use and care manual

Graco

Graco 224-617 User manual

Graco

Graco ProMix 2KE Instruction Manual

Graco

Graco XM Series Instruction Manual

Graco

Graco Series A Operation manual

Graco

Graco Magnum Pro Compact A15 258861 User manual

Graco

Graco 190ES 261825 User manual

Graco

Graco Merkur ES User manual

Graco

Graco 222973 Operation manual

Graco

Graco FUSION 309550U Operation manual

Graco

Graco dutymax gh 300 Operating instructions

Graco

Graco 238256 Operation manual

Graco

Graco True Airless LTS15 Instruction Manual

Graco

Graco 3A4803A Guide

Graco

Graco 295ST 233686 Operating instructions

Graco

Graco 24P930 User manual

Graco

Graco 223-773 A Series Datasheet

Graco

Graco Inline HD 245820 Guide

Graco

Graco GMAX 3400 Instruction Manual

Graco

Graco 16R955 Guide

Graco

Graco Series A Operation manual

Graco

Graco PRO AA5500SC User manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

DeVilbiss

DeVilbiss LUNA2i Operation manual

WAGNER

WAGNER W 125 manual

My Clean Buddy

My Clean Buddy PW018 user manual