Goldmund SRP2.3 User manual

GOLDMUND SRP2.3

PREAMPLIFIER

GOLDMUND SRP2.3 PREAMPLIFIER

USER MANUAL

ATTENTION :

No connection or manipulation must be done before reading these instructions. Damage to

the preamplifier may result if the following instructions are not consciously understood and

applied.

1 - UNPACKING

You will find in the GOLDMUND SRP2.3 box :

- The preamplifier.

- The remote Controller

- The power cord.

- This manual.

- Accessories and spare fuses.

Please keep the packaging in case you need to transport the preamplifier at a later date or if

you have to send it for maintenance.

2 - CHOICE OF PREAMPLIFIER LOCATION

The GOLDMUND SRP2.3 preamplifier generates a small amount of heat.

It is necessary to allow a proper cooling of the circuits. Avoid any location which is not

properly ventilated and avoid to put on top any equipment sensitive to temperature.

It is also a safe precaution to avoid direct proximity of the power amplifier, since the field

generated by some units can be detrimental for the SRP2.3.

3 - LINE VOLTAGE

A voltage indication is provided on the back plate of the unit. Check if this is appropriate for

your AC line voltage.

ATTENTION : With a 220V setting, the SRP2.3 preamplifier will function properly for AC line

voltage between 200V and 250V. On the 110V position, the AC mains must deliver between

95V and 125V. If your AC mains is usually out of these tolerances, please consult your

GOLDMUND dealer.

Please check the value of the AC line fuse. This fuse is located on the power cord receptacle.

The lid can be removed with a small screwdriver when the cord is removed.

Use a .5A slow-blow fuse for 220V and a 1A slow-blow fuse for 110V.

4 - CONNECTIONS

Connect the power cord to the back of the unit and plug it into the nearest wall plug. Use a 3

lugs grounded plug for safety. To get the best sound of the preamplifier, avoid any multiple

plugs or an extension cord.

Connect the interconnects between the preamp and the power amp. Plug the cables to the

RCA female sockets noted output.

Connect the interconnects from the source devices to the 5 inputs. Connect the tape

machines to TAPE input and output RCA plugs.

Note : If you have the digital input option, the inputs 3, 4 & 5 are not available anymore for

analogue sources. But inputs Digital 1 – 2 – 3 are active and may be connected to digital

sources.

Note : The analogue input 1 may be converted internally to a SSP Direct cinema input. Do not

use it for another source if you want to use this option. When set-up, the option is connecting

the input 1 to output bypassing all preamp circuitry. To activate the SSP option, just plug a

connecting Jumper on JP1 on the back of the circuit.

5 - CONTROLS AND UTILIZATION

- POWER ON

The GOLDMUND SRP2.3 preamplifier has no power switch. It is powered ON as soon as the

power cord is connected to the wall plug. It must remain connected all the time.

When powered on first, the preamp will become operative immediately. Do not power ON the

power amplifier immediately to insure proper stabilization of all the circuitry and avoid any

unwanted noises.

- VOLUME

Level adjustment acting simultaneously on both channels.

- SELECTOR

This selector allows to choose the source from one of the 5 inputs.

- REMOTE-CONTROL

The SRP2.3 uses a volume motor-driven potentiometer which can be adjusted by the remote

controller provided for increasing (+) or decreasing (-) the sound level.

In addition a "MUTING" control with soft stop and start is available through the remote control

which acts on the potentiometer.

The additional "MEMO" key on the remote allows to pre-program a standard level to which

the potentiometer will return when the unit is powered on or when the "RESET" key is

pressed.

Attention : If the potentiometer position you want to memorize is above the potentiometer's

half position, it won't be memorized and a value of ¼will be memorized instead. This is

provided by the software as a safety to avoid very high level memorization by accident with

potential danger for the speakers the next time the unit is turned on.

6 - SOUND QUALITY OPTIMIZATION

- Warm-up sonic effect.

If the preamplifier has been left unpowered for a few days, the optimum sound quality is only

reached after few hours. The critical circuits have to warm up to around +55 degrees Celsius

(+131 degrees Fahrenheit) before achieving their optimal performances.

7 - MAINTENANCE

The GOLDMUND SRP2.3 preamplifier usually requires no maintenance. For the audio purists

who want to keep their preamp sounding as new, we only recommend that after a year or two,

you have a technician or an official GOLDMUND representative readjust the DC offset. This

very simple operation takes only two minutes and will give you the safety of long years of

unmatched sound quality.

To clean your preamplifier use only a soft, slightly wet cloth. Always turn the power off before

cleaning your preamplifier.

TECHNICAL DATA

OUTPUT LEVEL

- Nominal level : 0.63 V RMS.

- Maximum output level : 3 V RMS.

- Output stage output impedance : < 10 Ohms.

- Corrected output impedance # 330 Ohms.

FREQUENCY RESPONSE

These values for any level to 17 V RMS.

- +/- 0.1 dB, 10 Hz - 100 kHz.

- +/- 1 dB, 6 Hz - 300 kHz.

- +/- 3 dB, 3 Hz - 0.65 MHz.

INPUT SENSITIVITY

- Nominal level : 150 mV.

- Saturation level : 6 V RMS.

- Nominal input impedance : 50 kOhms.

GROUP DELAY

Propagation delay < 300 ns stable with frequency from DC to 200 kHz.

DISTORTION

Figures valid for all levels from 0 to 25 V.

- Dynamic : TID < 0.01 % (- 80 dB).

- Static : THD < 0.01 % (- 80 dB).

SPEED

- Slew rate of the amplification stages : > 500 V/us

- Rise time : < 700 ns.

CROSSTALK

- Separation : > 90 dB between channels.

NOISE

- Signal-to noise ratio on line input : > 85 dB (0.01 Hz - 10 Mhz).

- Weighted ASA A : > 100 dB.

OPERATING TEMPERATURE

- Room temperature : -30 to +40 degrees Celsius ( -22 to +104 degrees Fahrenheit).

- Internal temperature : +45 to +65 degrees Celsius ( +113 to +149 degrees Fahrenheit).

POWER SUPPLY

- Nominal line voltage : 110 or 220 V.

- Input voltage range : +/- 15 %.

- Maximum power consumption : 10 W.

GROUNDING

- Common ground and earth.

- Chassis connected to signal grounding.

FRONT PANEL CONTROLS

- VOLUME control.

- SELECTOR switch.

REAR PANEL CONNECTORS AND CONTROLS

- AC line connector 3 lugs.

- Output and input connectors RCA (right and left), 3 Digital optional inputs RCA.

SIZE AND WEIGHT

- 44 cm W x 30 cm D x 6 cm H.

- Weight : 4 kG.

WARRANTY

- 3 years parts and labor.

Table of contents

Other Goldmund Amplifier manuals

Goldmund

Goldmund GOLDCUBE User manual

Goldmund

Goldmund TELOS 390.5 User manual

Goldmund

Goldmund PH7.3 User manual

Goldmund

Goldmund METIS 2 User manual

Goldmund

Goldmund Amplifiers User manual

Goldmund

Goldmund TELOS 590 NextGen User manual

Goldmund

Goldmund TELOS 3500 User manual

Goldmund

Goldmund SRI2 User manual

Goldmund

Goldmund TELOS 200 User manual

Goldmund

Goldmund TELOS 500 User manual

Goldmund

Goldmund TELOS 352 User manual

Goldmund

Goldmund TELOS 250 User manual

Goldmund

Goldmund TELOS 150 User manual

Goldmund

Goldmund TELOS 390 User manual

Goldmund

Goldmund MIMESIS 32 User manual

Goldmund

Goldmund Metis 5 User manual

Goldmund

Goldmund Metis 5 User manual

Goldmund

Goldmund PH3.8 User manual

Goldmund

Goldmund SRM250 User manual

Goldmund

Goldmund MIMESIS 24 User manual

Goldmund

Goldmund TELOS 280 User manual

Goldmund

Goldmund METIS 3 User manual

Goldmund

Goldmund MIMESIS 29.4M MILLENNIUM EDITION User manual

Goldmund

Goldmund TELOS 280 User manual

Popular Amplifier manuals by other brands

ASTRO

ASTRO HVO V40 P operating manual

Marantz

Marantz SUPERSCOPE BLA-545 Service data

NAD

NAD CI980 Quick setup guide

Technics

Technics SE-CH770 Service manual

Harman Kardon

Harman Kardon HK6300 instruction manual

NAD

NAD T975 owner's manual

McIntosh

McIntosh MA6850 Brochure & specs

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N manual

Viatron

Viatron Autrix Technical manual

GME

GME GA9800 instruction manual

Atlas

Atlas CP700 Specification sheet

Roland

Roland KC-1000 owner's manual

Pyle

Pyle PFMRA350BW user manual

Advantage

Advantage S-250 manual

IRT Electronics

IRT Electronics DVA-3007 manual

Dimavery

Dimavery BA-100 Series user manual

Sony

Sony XM-S400D operating instructions

Schertler

Schertler ROY X quick guide