Gold Apollo AL-A26 Operating instructions
Gold Apollo Co., Ltd.
PAGER PROGRAMMING GUIDE
Alpha-Numeric Display Pager
MODEL : AL-A26
Contents
Contents
PAGER PROGRAMMING SOFTWARE
August 8, 2006 V1.0
ALA26
GETTING STARTED ............................................................................................................................................................. 1
EQUIPMENT REQUIRED .............................................................................................................................................................. 1
EQUIPMENT SETUP .................................................................................................................................................................... 1
INSTALLING PROGRAMMER SOFTWARE..................................................................................................................... 3
INSTALLATION ........................................................................................................................................................................... 3
RUNNING ................................................................................................................................................................................... 6
ALA26 PROGRAMMING ...................................................................................................................................................... 7
INTRODUCTION.......................................................................................................................................................................... 7
STARTING THE PROGRAMMER ................................................................................................................................................... 7
CODE AND FEATURES MENU ..................................................................................................................................................... 8
Frequency............................................................................................................................................................................. 9
Capcode (Decimal Address) ................................................................................................................................................ 9
Message Type Status ...........................................................................................................................................................1 2
Auto Increase 1 after write .................................................................................................................................................. 14
ALERT AND STATUS .................................................................................................................................................................. 14
Alerts and Status ................................................................................................................................................................. 15
Manu Of Pager ..................................................................................................................................................................17
Manual Write ......................................................................................................................................................................18
Prompts ...............................................................................................................................................................................19
PROMPTS EDIT ..........................................................................................................................................................................19
SOURCE PROMPTS .................................................................................................................................................................... 20
FILE | OPEN (CTRL + O) ............................................................................................................................................................. 21
FILE | SAVE (CTRL + S) .............................................................................................................................................................. 21
FILE | EXIT (CTRL + E)................................................................................................................................................................ 22
PAGER | READ (F3) ...................................................................................................................................................................2 2
PAGER | WRITE (F4) ................................................................................................................................................................. 23
ABOUT ......................................................................................................................................................................................2 4
Getting Started
PAGER PROGRAMMING SOFTWARE
1
August 8, 2006
ALA26
Getting Started
provides the flexibility
to program ALA26 pagers
obtain the best results from the product, please take a few
minutes to read this instruction guide.
Equipment Required
To install and operate the programmer, you need a system that meets
the following minimum requirements:
An personal computer (PC) with printer port, or compatible
●
Windows 98 SE or above operating system (XP Recommended)
●
256 MB of RAM
●
ALA26 Programmer
●
A DB25 male-male printer cable
●
ALA26 Pager Programming Software
●
Equipment Setup
Refer to Figure 1 while performing the follows:
1. At the rear of the PC, connect the DB25 male-male interface
cable to the printer port on your computer.
2. Plug end of the DB25 cable into the ALA26 programmer.
3. Hardware installation is complete.
The ALA26 pager Programming software,
to meet individual requirements. To
Getting Started
ALA26
PAGER PROGRAMMING SOFTWARE
Computer
DB25 male-male
printer cable
Figure 1 Programmer Hardware Connections
Power LED
Press down on the
pager until it is tight
in the fixture.
AL-A26
Programmer
2
August 8, 2006
Installing Programmer Software
Installing Programmer Software
Installation
Install the programmer software into a PC as follows:
1. Uncompress the ALA26V373.zip and save them in
a temporary directory.
2. Double click the setup.exe file. Click on “Y”.
4. Enter your user information and click “Next”.
(Note: you must enter at least a single character "into the company field)
3. Click “Next” on the Welcome screen.
ALA26
PAGER PROGRAMMING SOFTWARE
3
August 8, 2006
Installing Programmer Software
5. Choose where the program should be installed and click “Next”.
6. On the Select Program Folder screen choose where you would like
the program to show up in your start menu and click “Install”.
ALA26
PAGER PROGRAMMING SOFTWARE
4
August 8, 2006
Installing Programmer Software
7. Click “Finish” on the Setup Complete screen.
ALA26
PAGER PROGRAMMING SOFTWARE
5
August 8, 2006
Installing Programmer Software
Running
You now have the program installed. To run it from the Start menu/Programs
/ Gold Apollo /ALA26 Pager Programmer
ALA26
PAGER PROGRAMMING SOFTWARE
6
August 8, 2006
ALA26 Programming
ALA26 Programming
Introduction
Preparing a Pager for Reading or Programming:
● Establish a computer hardware configuration.
● Run the programming software of ALA26.
● A Power LED illuminates on the Programming Interface to indicate
proper contact. If the Power LED did not illuminate then you must
check the configuration and restart the programming software of ALA26.
● Align the pager contact pin holes with the contact pins of the ALA26
Programmer.
● Press down on the pager until it is tight in the fixture.
● Turn the pager off or wait the pager until standby mode.
The pager is now ready to read or program.
Starting the Programmer
The application can be launched from Start → Programs → Gold Apollo
→ ALA26 Pager Programmer. The following window appears :
Input your password. If key in wrong password for 3 times, the system shuts
off automatically. If the password is correct, the following window appears :
ALA26
PAGER PROGRAMMING SOFTWARE
7
August 8, 2006
ALA26 Programming
Now, the system examines that the ALA26 programmer is
well installed. If any questions, the following window
appears :
Please re-check the ALA26 programmer and printer port
are well installed or not. If the connection with the ALA26
programmer are OK. The system enters the Code and
Features Menu ◦
ALA26
PAGER PROGRAMMING SOFTWARE
Code and Features Menu
8
August 8, 2006
Other manuals for AL-A26
1
Table of contents
Other Gold Apollo Pager manuals
Gold Apollo
Gold Apollo AL-A25 Operating instructions
Gold Apollo
Gold Apollo AL-A07 User manual
Gold Apollo
Gold Apollo VP200 Mounting instructions
Gold Apollo
Gold Apollo VP200 Operating instructions
Gold Apollo
Gold Apollo AL-A27 User manual
Gold Apollo
Gold Apollo AL-A28 Owner's manual
Gold Apollo
Gold Apollo AL-924 Operating instructions
Gold Apollo
Gold Apollo AL-A27 Operating instructions
Gold Apollo
Gold Apollo AL-A26 Operating instructions
Gold Apollo
Gold Apollo AP-700 User manual
