Gloview FP Board User manual
Manual for FP Board
FINGER TOUCH PORTABLE INTERACTIVE WHITEBOARD
FP BOARD MANUAL
V 2.0
Manual for FP Board
Contents
Introduction………………………………………….1
Specification Data and Package………………….2
Working Environment…..………..………….……. 2
Hardware Installation ……… ……………………..3
Calibration Software ……………………………….6
tBoard Software Manual……………………....…..9
Tips……………………………………………………14
Manual for FP Board
1
Introduction
Interactive Whiteboard FP Board is the first portable Interactive Whiteboard that supports finger touch. It can work with any
projectors or LCD screen and turn the projection screen or LCD Screen into finger touchable. Key features: portable and finger touch;
detect any non- transparent objects;Work on any surfaces, no limited on the material; active sizes range from 40”-85’’; can work with
common board and save the record of both mark pen and finger writing.
* 6 months replacement，2 years limited warranty for the FP Board model.
Features
1, Support finger touch.
2, Multi-writing.
3, Remote control with our new pen (Option).
4, Support to delete the words with the normal eraser.
5, Portable and easy to install.
6, Turn normal whiteboard or wall into finger touchable.
7, Any non- transparent objects like a rolled paper.
Specifications
calibration
Automatic Calibration/Manual Calibration
object detection
finger(stylus) or eraser
delay
<80 ms
minimum active work area
40'' diagonal
maximum active work area
85'' diagonal
tracking technology
Laser Image Calibration Technology (LICT)
Manual for FP Board
2
positional accuracy
±1 Pixel (Resolution: 1024 x 768)
average power
consumption
700mW
dimensions
Bar: L 70cm, Base: L 14cm x W 12.5cm x D 4.5cm
power requirements
110-240V, 50/60HZ, 2A
weight
0.65kgs
requirements
Windows XP, Vista, Windows 7
software
Calibration software and Application Software
certification
CE, FCC
Package Includes
Finger Touch Model 7m USB Cable Power Adaptor Pointer
CDs HardKey GL-IRP(Optional)
Working Environment
Computer
CPU：P4 2.8 or Above RAM：1G
Hard disk：20G
System：XP / Vista/ Win7
Manual for FP Board
3
Hardware Installation
1, There is a red tape on the base of FP Board as below. Please keep it and don’t peel off the red sheet.
2, Prepare a flat whiteboard: Please leave a space between the projection screen and whiteboard edge as marked as below.
3, If you choose to install with screws, please according to the following steps:
Take the cover of FP Board Base( Pic1). Put 4 screws and mount FP Board on the area marked in black area in the above picture.
The base of FP Board should be at the same level with the surface of whiteboard.
Set the bar perpendicular to the board. Tighten the upper screws and then the down screws (Pic2). The base of FP Board should be
touched on the board with a little space (Later we will adjust the angle of FP Board through fastening or loosening the
screws.)
FP BOARD
5cm
Manual for FP Board
4
(Pic1)
(Pic2)
If you choose to install with the double faced adhesive tape, please according to the following steps:
Put another two strip of double faced adhesive tapes onto the FP Board’s base (like Pic3), tearing the red layer, and put the FP
Board onto the board or wall. You’d better to use your hands to press the FP Board to the flat surface about 20 seconds to make
sure it can be sticky strongly.
(Pic3)
4, Connect one end of USB Cable to the USB Port of Computer, and the other end to FP Board. Plug the power cable into FP Board.
USB and Power cable should be exclusive to the projection screen. Plug the hardkey into the USB Port of computer.
Manual for FP Board
5
User can extend the bar according
the size of projection screen after
releasing this button.
User can adjust the
angle of the bar
through this button
User can adjust the
angle of the sensor
after releasing this
button
Manual for FP Board
6
Calibration Software
Open the small CD and copy the “Calibration Software” and “Application Software” file folders into your PC.
Calibration
1, Open the file of CALIBRATION SOFTWARE, run “Whiteboard Calibration”;
You can get a screen from sensor like below:
2, Change the angle of the sensor until the image is located under the line.
Manual for FP Board
7
Then touch each corner and check if it can be seen from the calibration screen like below. If some corner is not included, please
extend the bar or minimize the projection screen. Each corner must be involved.
3, Please choose “Automatic Calibration”from the menu or you can press Ctrl+Shift+C to do calibration.
Manual for FP Board
8
4, After you have finished the calibration, you can use the finger or the pen as a mouse on the projection screen.
5, The calibration software will be minimized at the right corner. Put the mouse on the icon and right click. You can make FP BOARD
run with the computer starting.
Table of contents
Other Gloview Whiteboard manuals
