Global 695803 User manual
1
globalindustrial.ca
User Manual Manual de Usuario Manuel de l'Utilisateur
Customer Service
US: 1-800-645-2986
Servicio de atención al Cliente
US: 1-800-645-2986
Service à la clientèle
Canada: 888-645-2986
Electrostatic Sprayer - 4.2 Gal.
With Lithium Battery and Charger
Specifications
Battery:
Working Time:
Tank Capacity:
Dimensions:
Lithium Battery 12V8A
4 hours
4.2 gallon
Effective Range:
Charging Time: 8 hours
Sprayer Volume: .75 gallon/min
15” x 9” x 20”
Weight:
Charging Power: 110V
10 to 16 ft.
Attachments: (4) Nozzles
Includes: Lithium Battery, UL Charger
13.9 lbs.
Model 695803
Read this manual thoroughly prior to
installation and operation. Keep these
instructions in a safe location for future
reference. For questions, visit
globalindustrial.com or contact
Customer Service at 1-800-645-2986.
WARNING
To reduce the risk of electrostatic shock,
continuously touch the copper strip on the
handle when the electrostatic switch is
turned on. Use caution when exchanging
hands; ensure one hand is touching the
copper strip at all times.
2
Electrostatic Sprayer
PRODUCT HIGHLIGHTS:
Fine Atomization
The diameter of the nozzle of the electrostatic
sprayer is relatively thin, and the mist sprayed is
4 times thinner than an conventional sprayer.
User can cover the same square footage while
using a fraction of the solution.
Electrostatic Disinfection
The electrostatic sprayer uses specialized
solution that is combined with air and atomized
by an electrode inside the sprayer. The spray
contains positively charged particles that adhere
to all surfaces and objects. The particles in the
spray are positively charged, so they are able to
cling and coat any surface they’re aimed at.
High Efficiency
The electrostatic spray clings to objects and
doesn’t easily run. The spray will form a film on
a surface and coat all sides of an object; there is
no need to go over the same area twice. This
not only saves on the amount of solution being
used, but also improves the spray efficiency and
rate.
OPERATION:
Installation
1) Insert o-ring and gasket into the groove of the
handle switch port of the sprayer.
2) Connect the wand to the sprayer handle.
3) Select the appropriate nozzle and attach it to
the end of the wand.
Note: Always tighten and inspect nozzles.
Test Sprayer
1) Turn and open the solution tank cap on the
top of the sprayer.
2) Add desired amount of solution into the solu-
tion tank and then close the cap.
WARNING
SAFETY WARNINGS:
Read all the instructions before installation and
operation of this appliance.
To reduce the risk of electrostatic shock,
continuously touch the copper strip on the
handle when the electrostatic switch is
turned on. Use caution when exchanging
hands; ensure one hand is touching the
copper strip at all times.
• To reduce the risk of injury, close supervision
is necessary when used near children.
• DO NOT contact moving parts.
• Only use attachments recommended or sold
by Global Industrial.
• To reduce the risk of electrical shock, do not
immerse electrode in water or other liquid.
• DO NOT touch or insert anything in the nozzle
of the sprayer while device is powered on. After
shutting down, the nozzle should be in contact
with the crop or the ground to eliminate residual
static electricity.
• Use only the battery and charger supplied by
Global Industrial.
• DO NOT let the nozzle touch objects while
spraying.
• DO NOT use static electricity in an environ-
ment with high humidity such as fog or rain.
• NEVER use static electricity during a lightning
storm.
IMPORTANT:
The electrostatic switch is located on the left
side of the base. This switch must be activated
before the power switch on the handle is turned
on. When the electrostatic switch is turned on,
user must touch the copper strip on the handle
at the same time.
Note: The electrostatic sprayer is safe, and will
not cause any harm to the human body.
Note: If the electrostatic needs to be tested, it
is safe to use a common electric pen to check if
the water in the tank is charged.
3
Electrostatic Sprayer
3) Turn on power switch at the handle and test
spray for approximately 30 seconds.
Note: To reduce the risk of electrostatic shock,
continuously touch the copper strip on the
handle when the electrostatic switch is turned
on. Use caution when exchanging hands;
ensure one hand is touching the copper strip at
all times.
4) Check to make sure all joints are tightly
sealed, and the spray and pressure are
normal.
5) If no abnormality, turn on the static activa-
tion switch on the side of the sprayer. Product
is now ready for use.
Issue Possible Cause Suggested Action
Troubleshooting
Unable to start or
sprayer suddenly
stops working.
1) The battery is out of power or has a bad
connection.
2) Sprayer is overheated due to excessive
use, circuit protector broke.
1) Charge battery or check all connection
lines to ensure they are connected
properly and secure.
2) Wait for the electric components to cool
down before attempting to turn on again.
Liquid isn’t spraying
out of the nozzle, or
the spray pressure
is unstable.
1) Nozzle may have blockage.
2) Solution may be leaking at a connection
point before it reaches the nozzle.
3) There is a blockage in the pump.
4) Suction tube is broken.
1) Remove nozzle and was off any debris.
2) Locate leak and tighten connection.
3) Remove solution pump cover and clean
out pump.
4) Replace the tube.*
Low pressure.
1) Solution tank filter, or spraying switch
filter is blocked.
2) The battery is low on power.
Charging Battery
1) Plug the charger cable into the charging
port on the side of the sprayer.
2) Plug the other end of the charger cable into
a power outlet. Charging time may vary, but is
approximately 10-12 hours.
• RED LED = Charging
• GREEN LED = Fully Charged
Note: Do not allow battery to stay uncharged
for an extended period of time. If the sprayer
is not being used, it is recommended to
charge the battery every 2 months to extend
battery life.
1) Clean out filters.
2) Recharge battery.
Sprayer is leaking at
a connection point.
1) Connections or attachments are not
screwed in tightly/properly.
2) Rubber seal is broken.
1) Tighten all screws and attachments.
2) Replace rubber seal.*
* For questions or additional information, contact Global Industrial Customer Service at 1-800-645-2986.
Not spraying well or
properly.
1) Nozzle is blocked.
2) Nozzle is broken.
1) Clean nozzle of any debris.
2) Replace nozzle.*
Other Global Paint Sprayer manuals
Popular Paint Sprayer manuals by other brands
Bonide
Bonide 051 Operation and service instructions
zogics
zogics Z-DAS instruction manual
KISANKRAFT
KISANKRAFT KK-KBS-165 Operation manual
Matrix
Matrix SG 650 Translation of the original instructions
Anest Iwata
Anest Iwata SGA-3 Installation, use & maintenance instruction manual
paasche
paasche VV Instructions and parts list
