Global Model 812410 User manual
globalindustrial.ca
Distribucion Industrial Globales S DE RL DE CF
Instruction Manual Manual de Instrucciones Manuel d'instruction
Customer Service
US: 1-800-645-2986
Servicio de atención al Cliente
México: 01.800.681.6940
Service à la clientèle
Canada: 888-645-2986
1
Model 812410
48” LED SHOP LIGHT - DOUBLE TUBES, 40W
Please read entire manual carefully prior to installation and use.
Failure to observe instructions could result in item damage, severe
personal injury, and/or property damage.
• Installation and servicing should be done by a licensed electrician.
• This product must be installed in accordance with the National
Electrical Code and all applicable local codes and safety standards.
• Any alteration or modification of this product is forbidden as it may
cause product malfunction, property damage, personal injury or death.
• To avoid electric shock or component damage, unplug unit before
installation or servicing.
• Be sure fixture temperature is cool enough before touching. Do not
clean or maintain the fixture while unit is energized.
• Never use the cord for carrying, pulling or unplugging the power light.
Grasp plug and pull to disconnect from outlet. Keep cord away from
heat, oil, sharp edges or moving parts.
• Never attempt to plug in or operate light with defective or damaged
wires, power cord, or power cord plug. All defective parts should be
replaced immediately by qualified personnel.
• This product is for indoor use only.
WARNING
SPECIFICATIONS
AC Input: 120-240V
50,000 Hours Rated Life
Double Tube
40W
120 Angle Beam, 5000K
4400lm, 110 lm/W
Power Coated Steel Housing
IP 20 Rated
• Keep this manual for future use.
• For additional questions or concerns, contact Global
Industrial Customer Service at 1-800-645-2986 or visit
www.globalindustrial.com.
Product Dims: 48"L x 4.5"W x 1.8"H
ETL/cETL
Output: 72V
Instruction Manual
2
INSTALLATION INSTRUCTIONS
RISK OF ELECTRIC SHOCK. READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL THIS LIGHT.
DISCONNECT MAIN POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE FIXTURE.
1
3 4
7
5 6
2
Cable
Note: Up to 4 lights can be linked together.
Install additional fixtures by following the same instructions as above.
Use the power cord to link two fixtures together, (see illustration above).
WARNING
48” LED SHOP LIGHT - DOUBLE TUBES, 40W
Using a 6mm drill bit, drill two holes in the desired
mounting surface area. Note: Ensure mounting surface
is adequate to support the weight of the light.
Using a hammer, tap the (2) 6mm wall anchors (provided)
into the drilled holes.
Insert and twist the (2) 3.9mm hooks (provided) into the
wall anchors until completely tight.
If mounting onto a solid hardwood surface, skip to step 3.
If mounting onto a solid hardwood surface, twist hooks
directly into the surface (anchors are not required).
Slide the hanging cables through the holes on each end of
the fixture, as seen in the illustration above.
If metal pull string is too high to reach, attach 3-ft. pullcord
extension (included).
Hang the fixture by looping the (2) cables around the
mounting hooks. Plug in power cord, and ensure the light
turns on. The fixture is now installed.
Other Global Lighting Equipment manuals
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
