Giant 2005 REIGN Series User manual
1
2005 Reign SERIES
DUAL-SUSPENSION BIKE
TECHNIC MANUAL
2
CONTENTS
PRODUCT FEATURE
SECTION 1. SIZING
SECTION 2. REAR SHOCK
SECTION 3. TORGUE SETTING
SECTION 4. EXPLOADE DRAWING
3
Reign Product feature
This bike is long travel XC bike. It can be go anywhere and anything.
The rear suspension system is a new design which is called maestro, this maestro feature is vpp
design and to get the overall suspension behavior to the best not only one point is the best .
1. Minimal power loss
2. Low kickback
3. Minimal brake lockout
4. Linear rising rate suspension design
5. Best traction
The Reign has some features are design as below
1. 5.8” rear travel and 6” front fork
2. Full cartridge bearing design
3. Diamond shape frame design for light weight and better rigidity
4. Full seat post adjustment
5. Full range size (15”~21”)
6. Aluxx SL tube
4
1. Sizing
The actual frame measurements and geometries are listed below.
Size 15.5〞16” 18〞20〞21”
Top Tube (mm) 560 570 590 613 630
Seat Tube (mm) 394 406 457 508 533
Seat Angle 73.5°73.5°73.5°73°73°
Head Angle 70°70°70°70°70°
B.B. Drop (mm) -12 -12 -12 -12 -12
Rear Center (mm) 438 438 438 438 438
Wheel Base (mm) 1071.4 1082.2 1105.5 1127.1 1145.5
2.Rear shock
The Reign series is all purpose dual suspension long travel XC bike. The Reign bike is capable of
climbing and descent the most technical of trails. The Reign offer three ProPedal damping setting to
reduces pedal induced suspension bob. You can find s setting that suits your riding style. Please
follow the guidelines below in setting up and maintaining your Giant Trance bike.
pump
Air valve
5
SPV Air Valve
Rebound adjuster
SPV 3 WAY SHOCK
Setup
SPV SET-UP QUICK REFERENCE GUIDE
This quick reference guide is to be used for setting up the any Swinger shock. Follow this order to
ensure the best possible tuning.
* Coil and Air Shock Initial Set Up
1. Adjust Sag:
Sag is the amount the shock compresses under normal body weight. On the air shock, there are sag
incrementations on the inside of the shock that can be used to help adjust sag.
Cross country: 25-30% Sag
Freeriding: 30-40% Sag
2. Set SPV Pressure:
Range should be between 75 and 150 psi. Pressure should be between 50-70% of body weight. More
pressure will create more compression damping, hold the bike up more and pedal better. Less pressure
will create less compression damping, allow more sag, and be more responsive and supple.
3. Set SPV Volume:
You should begin with the 16mm adjuster completely backed out. Turning the volume adjuster
inwards will create a more progressive damping effect making the suspension firmer from the middle
to bottom out. Turning the volume adjuster outwards will make the rear shock more linear in
compression damping and be a softer finish.
4. Rebound Damping:
Turn the blue knob located on the eyelet mount clockwise to increase rebound damping.
5. Low Speed Compression Damping (6-way adjust only):
Turn in the red adjustment knob to increase chassis stability (also may decrease supply feel of shock).
6. High Speed Compression Damping (6-way adjust only):
Turn in the black adjustment knob to increase high-speed bottom resistance.
6
*Note:
On the 6-way shock, please make sure that the two compression adjuster knobs on the reservoir are
fully open when setting the shock pressure and volume. You can turn them after you set up the
pressure and volume adjuster to achieve more compression damping.
7
3. Torque settings
The bolts used to attach the rear suspension unit are very high grade products factory installed to
specific torque specification. If it becomes necessary to remove or tighten the pivot bolts extreme care
should be taken when re-tightening them.
All bolts should be cleaned and re-set using LocTite Primer (﹟243)
All bolts location and tighten torque please refer to the illustration below.
1 5
4
3
2 7
6
Torque settings:
1. Main pivot 120 -150 Kgf/cm. or 104 -130 in-lbs.
2. Seatstay pivot 120 -150 Kgf/cm. or 104 -130 in-lbs.
3. Main linkage pivot 90 -110 Kgf/cm. or 78 - 95 in-lbs.
4. Upper shock mount 90 -110 Kgf/cm. or 78 - 95 in-lbs.
5. Lower shock mount 120 -150 Kgf/cm. or 104 -130 in-lbs.
6. Chainstay pivot 120 -150 Kgf/cm. or 104 -130 in-lbs.
7. Llinkage connect pivot 90 -110 Kgf/cm. or 78 - 95 in-lbs.
8
4.Explode Drawing
THE DRAWING BELOW SHOWS RELATIONS OF EVERY PARTS AND FRAME
Table of contents
Other Giant Bicycle manuals
Giant
Giant SEDONA LX W User manual
Giant
Giant TWIST FREEDOM DX User manual
Giant
Giant AVAIL ALLIANCE User manual
Giant
Giant TCR Alliance User manual
Giant
Giant TCR ADVANCED 1 - DATASHEET 2 User manual
Giant
Giant NRS 2004 User manual
Giant
Giant E-bike User manual
Giant
Giant XTC 1 User manual
Giant
Giant REIGN User manual
Giant
Giant ANTHEM X ADVANCED SL 0 - DATASHEET 2 User manual
Giant
Giant Anthem 29 Series User manual
Giant
Giant ANTHEM X User manual
Giant
Giant Propel Advanced SL Disc Series User manual
Giant
Giant SUSPENSION - User manual
Giant
Giant BELLA User manual
Giant
Giant GLORY - SERVICE V2.0 User manual
Giant
Giant XTC 29ER 1 User manual
Giant
Giant Integrated Seatpost User manual
Giant
Giant BOWERY 84 User manual
Giant
Giant SEDONA W User manual
