GFA ELEKTROMAT ST 80.24-50,00 User manual
f
Pos: null /BA_Module/BA_ AA Deckblatt/BAAA000 001_M003 @ 17\mod_14442117 55814_28.docx @ 891110 @ @ 1
Installation Instructions
ELEKTROMAT
ST 80.24-50,00
Model: 10003195 00001
-en-
Status: 06.03.2020
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
2
Pos: null /BA_Module/BA_ CA Leerblatt/BACA00 0001_M002 @ 15\mod_1416821 436083_28.doc x@ 864410 @ @ 1
GfA ELEKTROMATEN GmbH & Co. KG
Wiesenstraße 81
D-40549 Düsseldorf
www.gfa-elektromaten.de
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
3
Pos: null /BA_Module/BA_ DA Inhaltsverzeic hnis/BADA000001_M001 @ 0\ mod_1192624580455_28. docx @ 710 @ @ 1
Table of contents
1General safety information .............................................................................................. 4
2Technical Data ................................................................................................................ 5
3Mechanical installation .................................................................................................... 6
4Electrical installation ..................................................................................................... 10
5Motor connection .......................................................................................................... 11
6Limit switch connection ................................................................................................. 11
7Completing commissioning / inspection ......................................................................... 12
8Declaration of incorporation / Declaration of conformity ................................................. 14
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
Symbols
Warning - Potential injury or danger to life!
Warning - Danger to life from electric current!
Note - Important information!
▶ Requirement - Required action!
Schematic representations are based on product examples. Deviations from delivered
products are possible.
4
Pos: null /BA_Module/BA_ EA Sicherheitshinweise/BAEA 000004_M003 @ 10\mod_1 362389720702_28.doc x@ 7848 40 @ 1 @ 1
1General safety information
Specified normal use
The drive unit is intended for horizontally operating sliding doors.
The safe operation is only guaranteed with specified normal use. The drive unit is to be
protected from rain, moisture and aggressive ambient conditions. No liability for damage
caused by other applications or non-observance of the information in the manual.
Modifications are only permitted with the agreement of the manufacturer. Otherwise the
Manufacturer’s Declaration shall be rendered null and void.
Safety information
Installation and initial operation tasks are to be performed by skilled personnel only.
Only trained electrical craftsmen are permitted to work on electrical equipment. They must
assess the tasks assigned to them, recognise potential danger zones and be able to take
appropriate safety measures.
Installation work is only to be carried out with the supply off.
Observe the applicable regulations and standards.
Coverings and protective devices
Do not operate unless corresponding coverings and protective devices are installed.
Ensure that gaskets are fitted correctly and that cable glands are correctly tightened.
Spare parts
Only use original spare parts.
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
5
Pos: null /BA_Module/BA_ FA Technische Daten/BAF A001103_M001 @ 0\mod_119323 7363659_28.doc x@ 1290 @ 1 @ 1
2Technical Data
Type SG 115R
Output torque 800 Nm
Output speed 24 rpm
Output shaft / hollow shaft 50,00 mm
Maximum output speed open / close
for frequency inverter operation 42 / 42 rpm
Maximum door weight 80000 N
Supply voltage 3N~ 400 V
Operating current 4,70 A
Operating frequency 50 Hz
Power factor cos φ 0,77
Maximum movement per hour 10 h-1
Class of protection IP 54
Limit switch range
(maximum revolutions of output shaft / hollow shaft) 20
Braking torque of magnetic brake 130 Nm
Braking voltage 103 V DC
Rectifier type B1 230/103
Temperature range -10 / +40 (+60) °C
Pos: null /BA_Module/BA_ FC Temperaturbereic h/BAFC000002_M002 @ 23\mod_151 1339779197_28.doc x@ 105987 8 @ @ 1
1) When using a temperature range of +40°...+60°C use half of maximum movements per hour.
Temperature Extension!
If the magnetic brake will be continuously supplied the drive can be fitted into areas
down to a -20°C ambient temperature.
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
6
Pos: null /BA_Module/BA_ GA Mechanische Montage/ BAGA004301_M001 @ 10\mod_1 365771756315_28.d ocx @ 788330 @ 1 @ 1
3Mechanical installation
Requirements
The permissible loads on walls, mountings, connection and transmission elements must not
be exceeded even for maximum holding or locking torque (▶ observe technical data).
Connection elements
▶ Use self-locking
connection elements with
a minimum strength of
800 N/mm2 (8.8).
▶ Use a screw that
precisely fits the hole.
▶ Use adequately
dimensioned washers for
elongated holes.
BAGAB00002_Z002 BAGAB00003_ Z002
3 : 1
Permissible mounting positions
BAGAC04301_Z002
7
Mounting
4 boreholes are provided for mounting.
BAGAD04301_Z002
8
Installation
The following descriptions refer to a door which is not further defined. The door
manufacturer's specifications must also be observed.
Warning – Injury or danger to life possible!
Use a lifting device with sufficient load-carrying capacity for installation tasks.
Adequate space around the adjusting screw must be ensured for the safe
activation of the slipping clutch.
▶ Tighten all connection elements (M16) with
a torque of 175 Nm. Install all further
connection elements according to the
specifications of the door manufacturer.
BAGAE004302_Z002
175 Nm
9
Warning – Injury or danger to life possible!
Disconnect the electrical voltage for the setting of the slipping clutch.
▶ The slipping clutch acts as an overload
protection. The factory setting for the
tightening torque is 24Nm (ST 60) or 30Nm
(ST 80). Rotation to the right will increase
the transmittable torque. Rotation to the
left will decouple the drive unit from the
door.
BAGAE4303_Z002
SW 17
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
10
Pos: null /BA_Module/BA_ HA Elektrische Montage/ BAHA190300_M001 @ 0\mod_ 1260284652159_28. docx @ 462982 @ 1 @ 1
4Electrical installation
Warning - Danger to life from electric current!
Switch the mains OFF and check that the cables are de-energised
Observe the applicable regulations and standards
Make the electrical connection according to standard
Use suitable tools
Performing electrical installation
Remove the cover. Insert the motor plug.
Connect the brake cables.
BAHAA19_Z001
BAH AB03_Z001
Completing the electrical installation
Mount the cable entries and/or cable glands.
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
Other manuals for ELEKTROMAT ST 80.24-50,00
1
This manual suits for next models
1
Table of contents
Other GFA DC Drive manuals
GFA
GFA 10004146 10011 User manual
GFA
GFA ELEKTROMAT SI 17.30 FU-30,00 User manual
GFA
GFA ELEKTROMAT SG 50F User manual
GFA
GFA ELEKTROMAT ST 80.24-50,00 User manual
GFA
GFA KE 9.24-25,00 Ex User manual
GFA
GFA 10002624 10011 User manual
GFA
GFA ELEKTROMAT SI 45.15 FU-40,00 User manual
GFA
GFA ELEKTROMAT SIK 25.10 WS-30,00 User manual
GFA
GFA ELEKTROMAT SI 17.24-30,00 User manual
GFA
GFA ELEKTROMAT SIK 17.10 WS-30,00 User manual
GFA
GFA ELEKTROMAT SI 140.20 FU-55,00 User manual
GFA
GFA ELEKTROMAT SE 9.15 WS-25,40 User manual
GFA
GFA ELEKTROMAT SI 75.15-55,00 User manual
GFA
GFA ELEKTROMAT SI 85.10-55,00 GA85/10GD User manual
GFA
GFA ELEKTROMAT SI 40.15-40,00 Ex User manual
GFA
GFA 10004055 10011 User manual
GFA
GFA SIK 25.10-30,00 User manual
GFA
GFA ELEKTROMAT SI 14.20-25,00 User manual
GFA
GFA ELEKTROMAT SI 55.20 FU-40,00 User manual
GFA
GFA ELEKTROMAT SI 13.100 FU-25,40 User manual
Popular DC Drive manuals by other brands
ABB
ABB RSYC-01 user manual
Rockwell Automation
Rockwell Automation PowerFlex 700S Programming manual
WEG
WEG DeviceNet CFW500 user manual
Siemens
Siemens SINAMICS G List manual
Siemens
Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Operating instructions & installation instructions
SOMFY
SOMFY JR RU 30 instructions