Getinge CS100 User manual

Note: This is an abbreviated guide

for proper baery operation and

maintenance for the CS100 and CS300.

For complete product instructions,

please refer to the CS100 and CS300

Operating Instructions.

CS100/CS300 Baery Operation

Quick Reference Guide

CS100/CS300 BATTERY OPERATION

Intro

Introduction

This Quick Reference Guide is designed to highlight the location,

functionality, alarms and maintenance of the lead acid batteries that

accompany the CS100 and CS300 Intra-aortic Ballon Pumps.

The CS100 and CS300 batteries are designed to be used during transport

or portable operation and it is critical to keep these batteries charged at

all times to avoid interruption in power during transport. Additionally, it is

important to maintain the batteries in accordance with CS100 and CS300

Operating Instructions.

CS100 CS300

3CS100/CS300 BATTERY OPERATION

Table of Contents

Section Page #

Baery Overview 4-6

Baery Status 7-14

CS300 Baery Operation 15-20

CS300 Baery Preventive Maintenance 21

CS100 Baery Operation 22-30

CS100 Baery Preventive Maintenance 31

Key Baery Warnings and Cautions 32

CS100/CS300 BATTERY OPERATION

CS100/CS300 Internal Battery Specifications

Baery Overview

Type: 24 VDC (nominal), 17.2 Amp-hours

Sealed lead acid, maintenance free

Run Time: (full charge) 2.25 hours minimum (from full charge, 120 bpm, 22 ± 5 °C)

Approximately 3.0 hours typical with new baery (from full

charge, 90 bpm, 22 ± 5 °C)

NOTE: A reduction in runtime can occur over a baery's life for reasons such as age,

storage temperature and discharge depth.

Recharge Time: 18 hours minimum (from complete discharge to full charge,

22 ± 5 °C), 8 hours to achieve at least 90 percent charge

(typically).

5CS100/CS300 BATTERY OPERATION

CS100/CS300 Battery Information

CS100/CS300 Batteries

The IABP includes a battery pack which contains two sealed lead acid

batteries. The batteries are maintenance free. There is no need to add

water or electrolyte. The batteries are sealed to prevent leakage from the

terminals or case.

Replace batteries as required. Batteries should be replaced after 100 full

discharge cycles, at no more than three (3) year intervals, or if run time is

less than the minimum run time of 135 minutes minimum at 120 bpm.

Disposal of batteries should be conducted in accordance with local

statutes and the labeling shown on the battery pack.

Baery Overview

CS100/CS300 BATTERY OPERATION

CS100/CS300 Optimum Battery Performance

To obtain optimum battery performance and expected battery life the following guidelines should be observed.

• The batteries should be maintained at full charge when the IABP is not in use. It is required that the IABP be plugged

into an AC outlet when the system is not in use. Verify the battery is charging by observing the charge indicator on

the pump module. If the unit must be stored for an extended time period (2 months or longer} and AC power is not

available to maintain the internal battery, or if the unit is stored in an ambient exceeding the maximum operating

temperature, disconnect the system battery pack from the system console. Due to battery self-discharge the

disconnected batteries must be fully recharged at least every four months.

• The battery contains a safety vent that will allow gases to be released should its rating be exceeded. If this vent is

actuated do not operate the unit and contact a qualified service representative.

• Do not short circuit the battery or battery pack terminals. Keep battery pack covers on at all times to avoid objects or

liquids falling on batteries.

• Excessive heat is very detrimental to battery life. Do not operate the system in ambients above the maximum

operating temperature.

• DO NOT attempt to repair the battery. If the case is cracked or terminal leads are broken replace with the same

rate battery.

• DO NOT disassemble battery. The battery contains an electrolyte which can injure skin or damage clothing. In the

event that electrolyte gets on skin or in eyes, immediately flush with water for 15 minutes and get prompt medical

attention.

• Batteries must be replaced as pairs, (i.e., same lot/date code).

• When a Low Battery message is displayed after any system operation, the battery should be recharged within several

hours to prevent battery damage

Baery Overview

7CS100/CS300 BATTERY OPERATION

Viewing Battery Status on Front Panel

Baery Status

IABP ON/OFF

This is the ON/OFF switch for the IABP console and monitor module. Operation of

this switch does not aﬀect the status of the internal baery charger.

Baery Charging LED

This indicator has three states:

• It illuminates continuously when the internal baeries are fully charged

• The LED indicator ﬂashes when the internal baeries are charging

• CS300: It is not illuminated when system is using the baery as a power source, or

when AC power is not available to the system, or when the system baery is faulty.

CS100: The Baery In Use status message and the Baery Indicator are displayed

when the system is operating from the internal rechargeable baery.

IABP ON/OFF

CS300

Automated Counterpulsation

INTELLIS ENSE TECHNOLO GY

Front Panel

Battery

Charging LED

FOR CS100:

CAUTION: The internal baeries are charging only when the

AC Mains plug is connected to an active AC Mains source,

the AC Mains switch is “On”, and the baery charging status

LED is illuminated. This charging condition must be maintained

even when the system is not in use. Note that 18 hours of charging

is required to fully charge the baeries.

FOR CS300:

CAUTION: The system should be conﬁgured to charge the

internal baeries whenever AC power is available. Hence, keep the

system connected to a live AC receptacle with the Mains On/Oﬀ

switch in the “On“position. If the system is to be stored for extensive

periods of time, or in ambient temperatures above the operating

range, see the Baery Section of the User Maintenance Chapter in

the Operating Instructions for additional information.

CAUTION: When AC power operation is intended, insure that the

system is plugged into AC mains, that the mains switch is in the “On”

position, and that the Baery in Use informational message in

NOT displayed.

It is extremely important to know the status of the IABP baeries at all times, as the status of the internal baeries aﬀects the performance and

operation of the unit. There are two ways to determine the baery status, on the front panel and on the display screen.

CS100/CS300 BATTERY OPERATION

Viewing Battery Status on Display Screen

Baery Status

Note: The display shown is for

illustrative purposes and does not

represent actual clinical conditions.

Alarm and Advisory Messages Area

This section of the screen displays alarm and advisory messages. The top-most line is reserved

for high priority alarms. The lower three (3) lines are shared to display any medium/low level

alarms or informational messages. If more than one message is displayed, they are posted in

priority order. See Alarms and Advisory Messages on page 9 of this document, for more

information regarding priority. As conditions are corrected, the corresponding message is

cleared and the next highest priority alarm or informational message is displayed. Pressing

the HELP key will access the appropriate help screen for the displayed condition. See “Help

Screens” in the Operating Instructions for more information.

Baery Indicator Icon

This icon indicates the approximate charge remaining in the internal baeries.

This indicator is displayed only when the system is powered by the internal baeries.

NOTE: The Low Baery Medium Priority Alarm is displayed when less than 30 minutes (approximately) of

internal baery life remains. When this message appears, the baery symbol is displayed as empty and

starts ﬂashing. See the Troubleshooting and User Maintenance Chapters in the Operating Instructions for

additional information.

TRIGGER

HEART RATE

bpm

MEAN

mmHg

AUG.

mmHg

AUG. ALARM

mmHg

SYSTOLIC

mmHg

DIASTOLIC

mmHg

IAB STATUS

PRESSURE

SOURCE

IAB FILL MODE

SLOW GAS

ALARM

•LEAD

•GAIN

ECG

OPERATION

MODE

ALARM &

ADVISORY

MESSAGES

Automated Counterpulsation

Normal

External

Auto

19 mm Auto

Threshold

Helium

115

120

0.5 mV

Infl. Defl.

0.0

Pressure

AUTO

Unassisted 99

Unassisted 51

22 min in

Standby

Check IAB Catheter

Battery In Use

Low Battery

Auto Zeroing

HELP Available for Alarm/Advisory Battery

!!!

Off

Display Screen

Alarm & Advisory

Messages Area

Battery

Indicator Icon

Battery

Associated Help Screen

Probable Cause Corrective Actions

The IABP is being powered from the

internal baeries.

1. Verify that it is necessary to operate from the internal baery. If appropriate, switch to the AC power source.

2. Verify MAINS power switch, located above the AC power cord connector, is ON.

CAUSE AND RESPONSE:

Operation

Trigger Mode

Trigger

Source Detailed Cause System Response Reset

All All Indicates System is operating

from an internal baery.

Unaﬀected Message clears when power is received from AC power source.

BATTERY IN USE

9CS100/CS300 BATTERY OPERATION

Battery Alarms and Advisory Messages

Baery Status

The IABP utilizes both auditory and visual alarm signals to communicate the need for attention or awareness by the

pump operator. Auditory alarm signals (tone sequences) are primarily intended to attract the attention of the

operator. They were carefully developed to communicate the urgency of the response, as well as the pump’s location.

Auditory signals are effective over a relatively broad range of operator positions.

CAUTION: Do not set the alarm volume to such a low level that it cannot be readily heard over the ambient

noise level of the venue in which the IABP is used.

Visual alarm signals consist of both display panel symbols and text. The displayed information further reinforces the

urgency of the alarm (symbol shape, color & flashing property) and also identifies the alarm via a specific text

message. Textual information is legible at the operator’s position, up to 1 meter from the front of the display panel.

Additionally, alarms are further complimented by an option to display context sensitive help information to aid in the

understanding and guide in the resolution of the alarm condition.

Alarm and advisory messages are grouped into the following categories in order to facilitate operator awareness and

understanding:

• Technical Alarms

• High, Medium and Low Priority Alarms

• Informational Messages.

These messages are displayed based upon the priority of the condition(s) that prompted them. Technical Alarms and

High Priority Alarm messages are displayed in the top line of the Alarm and Advisory Messages section of the display.

Medium/low level alarms or informational messages are displayed in the 3 lines below the top line. When a Medium

Priority Alarm – such as a Battery Alarm – is displayed, IAB assist is not suspended and the Medium Priority Alarm

tone is sounded. Medium Priority Alarms require the Operator’s prompt response.

CS100/CS300 BATTERY OPERATION

Medium Priority Alarms

Baery Status

Medium Priority Alarms indicate situations in which a prompt Operator

response is required. This class of alarm does not suspend pumping but

may indicate a need for corrective action. A yellow flashing alarm icon with

two (2) exclamation points denotes Medium Priority Alarms.

All Medium Priority Alarms have a uniform audio tone. The combination

of three (3) notes for Medium Priority Alarms is played in the following

sequence: three notes apause and then this cycle repeats.

NOTE: A “Low Battery” is categorized as a Medium Priority Alarm.

Medium Priority Alarm Icon

This manual suits for next models

Table of contents

Other Getinge Medical Equipment manuals

Getinge

Getinge ARJOHUNTLEIGH AURA User manual

Getinge

Getinge Maquet SERVO-i User manual

Getinge

Getinge Maquet Orchide User manual

Getinge

Getinge Maquet FLOW-i 4.2 User manual

Getinge

Getinge Arjohuntleigh Ninjo Series Instruction manual

Getinge

Getinge ARJOHUNTLEIGH Maxi Air Transfer User manual

Getinge

Getinge Arjohuntleigh Typhoon Instruction manual

Getinge

Getinge Arjohuntleigh Maxi Sky 600 ECS User manual

Getinge

Getinge MAQUET HLX 3000 User manual

Getinge

Getinge MAQUET CARDIOHELP User manual

Getinge

Getinge MEERA 720001B2 Operation and maintenance manual

Getinge

Getinge Arjohuntleigh Akron Streamline 2 Section User manual

Getinge

Getinge ArjoHuntleigh Flowtron ACS900 User manual

Getinge

Getinge Arjohuntleigh Parker User manual

Getinge

Getinge Arjohuntleigh Nimbus 3 Professional User manual

Getinge

Getinge Arjohuntleigh NIMBUS II User manual

Getinge

Getinge Blue 80/80 User manual

Getinge

Getinge MAQUET CRITICAL CARE User manual

Getinge

Getinge Volista User manual

Getinge

Getinge Flow-i User manual

Getinge

Getinge Arjohuntleigh AtmosAir 300 User manual

Getinge

Getinge LUCEA 10 User manual

Getinge

Getinge Arjohuntleigh Akron Bobath 4 User manual

Getinge

Getinge Maquet SERVO-i User manual

Popular Medical Equipment manuals by other brands

TekTone

TekTone Tek-CARE160 Installation and operation manual

NeuroMetrix

NeuroMetrix Quell 2.0 user manual

AMT

AMT XLR8 Quick reference guide

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 instruction manual

EDAN

EDAN SONOTRAX Pro user manual

Restorative Therapies

Restorative Therapies RT300 Service guide

Gendex

Gendex Expert DC installation manual

Dexcowin

Dexcowin ADX4000W user manual

Libelium

Libelium MySignals user manual

Acelity

Acelity V.A.C.ULTA 4 user manual

Caputron

Caputron ActivaDose II tDCS quick start guide

FujiFilm

FujiFilm Sonart Features

Plinth 2000

Plinth 2000 93CDT Service manual

GE SENOGRAPHE 800T Operator's manual

GE Definium 5000 Operator's manual

Kanmed

Kanmed GE-1380 user manual

Huntleigh

Huntleigh FD1 Instructions for use

Stryker

Stryker SPR Plus Operation manual