Genquip Gi3300 DSP User manual
page 1Genquip Gi3300 DSP Inverter Generator
Genquip Gi3300 DSP Inverter Generator
Owners Manual
page 2 Genquip Gi3300 DSP Inverter Generator
page 3Genquip Gi3300 DSP Inverter Generator
Control Function 4
Pre Operation Checklist 5
• Fuel System
• Refueling & Fuel Level Gauge
• Engine Oil
Control Function Continued 6
• Oil Warning System
• Engine Switch
• DC Protector
Operation 7
Starting The Engine
Periodic Maintenance 8
Spark Plug Inspection &
Oil Replacement 9
Engine Oil Replacement 10
Fuel Filter 11
Fuel Tank Filter 11
Air Filter Maintainence 11
Valve Adjustment 12
Genquip Safety 13, 14, 15
Operating Procedure 16
• Visual Inspection
• Start Up
• Shutdown
Maintaining your Generator 17
• Cleaning
• Storing or Transporting
• Servicing
Specications & Dimentions 18
Wiring Diagram 19
Troubleshooting 20, 21
• Engine Won’t Start
• Generator Won’t Produce Power
• Storage : Drain The Fuel
• Storage : Engine
Warranty 22
Notes 23
Table of Contents
page 4 Genquip Gi3300 DSP Inverter Generator
Control Function
Description and Control Panel Key
1. Carrying Handles
2. Fuel Level Gauge
3. Fuel Cap and Vent
4. Fuel On/Off Switch
5. AC Ready Pilot Light
6. Oil Warning Light
7. Ground (Earth) Terminal
8. 240 Volt Sockets
9. Engine On/Off Switch
10. Choke Knob
11. Recoil Starter
O N
CHOKE
D IG ITA L
T EC H
D C 12V 8A
O N O F F
(P USH )
PR O T E C TO R
O N
STO P
EC O N
O N
O FF
A C
TO R ESET A C
RESTART EN G IN E
1
23
1
9
10
11
12
13
4
56
78
page 5Genquip Gi3300 DSP Inverter Generator
Pre Operation Checklist
Note: Pre-operation checks should be made each time the generator is used.
Fuel System
Make sure there is sufcient fuel in the tank. The engine must use regular unleaded
petrol only and the fuel tank capacity is 7 litres.
Refueling And Fuel Level Gauge
To refuel, remove cap and fuel slowly until fuel gauge indicates full. Apply fuel cap and
turn fuel vent to the ON position.
WARNING: Fuel is high ammable and poisonous.
DO NOT ll above the top of fuel ller or it may
overow when the fuel heats up and expands.
Wipe up any spilled fuel immediately.
After refueling, make sure the tank cap is tightened.
Engine Oil
Make sure the engine oil is at the upper level of the oil ller hole. Add oil as necessary.
Recommended oil for most climates is 10W30. Engine oil quantity is 600 millilitres.
Fuel Cap and Vent
Fuel Level Gauge
“F” Full
“E” Empty
page 6 Genquip Gi3300 DSP Inverter Generator
Control Function Continued
Oil Warning System
If the oil level falls below the safe operating level, the engine will stop automatically.
Unless you rell with oil, the engine will not start again.
Note: If the engine stalls or does not start, turn the engine switch to “ON” position and
then pull the recoil starter. If the oil warning light ickers for a few seconds, the engine oil
is low. Add oil and restart.
Engine Switch
The engine switch controls the ignition system.
A. Ignition circuit is switched on.
The engine can be started.
B. Ignition circuit is switched off.
The engine will not run.
DC Protector
The DC Protector turns of automatically when the loads exceeds the generator rated
output.
Note: If the DC Protector trips to the OFF position, press to reset. Reduce the load to
the specied generator output if the DC protector turns off. If it turns off again, consult
the authorized dealer.
A
B
ON
STOP
ON
(PUSH)
PROTECTOR
OFF
page 7Genquip Gi3300 DSP Inverter Generator
Operation
Starting The Engine
Note: Before starting the engine, do not connect any electric devices.
1. Turn the fuel switch lever to the “ON” position.
2. Turn the engine switch to the “ON” position.
Note: Sometimes the choke is required to start a warm engine.
3. Hold the choke knob fully out.
4. Pull slowly on the recoil starter until it is engaged, then pull it briskly.
5. After the engine starts, warm up the engine until the engine does not stop when the
choke knob is returned to the original position.
6. Push the choke knob back to the original position.
Note: When starting in cold conditions (below 5˚C) run the engine with choke applied
for two to three minutes to warm up motor.
ON OFF
A
B
ON
STOP
1. 2.
CHOKE
CHOKE
3. 6.
page 8 Genquip Gi3300 DSP Inverter Generator
Periodic
Maintenance
Spark Plug 1. Clean Adjust
2. Replace 1 2
Valve Clearance Check Adjust 4
Engine Oil 1. Check
2. Replace 12* 2* * *
Air Cleaner 1. Check
2. Replace 1 1 2
Fuel Filter Replace 4
Clean Spark
Arrester-Screen 4
Recoil Starter Check operation 4
Choke Handle Check operation 4
Fuel System Check hose condition
look for leaks 4 4
Fittings Fasteners Check and Tighten 4 4
Cooling System (Air) Check for obstructions 4 4
Exhaust System Check for obstructions 4
Item
* First 20 hours & then every 50 hours
Attention
1 Month or 20 hours
Pre-operation (Daily)
3 Months or 50 hours
6 Months or 100 hours
12 Months or 300 hours
page 9Genquip Gi3300 DSP Inverter Generator
Spark Plug Inspection & Oil Replacement
You should periodically remove and inspect the spark plug.
1. Check for discoloration and remove the carbon.
2. Check the spark plug type and gap.
• Standard electrode color: Tan Color
• Standard Spark Plug: BPR4ES(NGK)(F7RTC)
• Gap: (0.028-0.031 inches)
3. Install the spark plug.
• Spark Plug Torque:14 lbs. -Ft.
(0.028-0.031 inch)
page 10 Genquip Gi3300 DSP Inverter Generator
Engine Oil Replacement
1. Place the machine on a level surface and warm up the engine. Then stop the
engine.
2. Remove the rubber cap on the bottom..
3. Place an oil pan under the engine. Remove the drain bolt
4. Open the oil ller cover as shown and remove the oil ller cap so that the oil can be
completely drained.
5. Check the drain bolt, gasket, oil ller gap and O-ring.
6. Reinstall the oil drain bolt.-Drain Bolt Torque:12 Ft. lbs.
7. Add engine oil to the upper level.
• Recommended oil for most climastes: 10W30
• Engine Oil Quantity: 600 millilitres
CAUTION: Be sure no foreign material enters the crankcase.
8. Install the oil filler cap.
9. Install the rubber cap on the bottom.
CAUTION: Be sure to install securely to prevent from falling off
during operation.
10. Close the oil filler cover.
Table of contents
Other Genquip Portable Generator manuals
