Genelec 7060B User manual

Quick setup guide

7060B-7070A-7071A

0

+6

+12

+3

-3

-6

-4

0

+6

+12

+3

-3

-6

-4

PHASE

0/-180 DEG

0/-90 DEG

ROLL-OFF

ON

-2 dB

-4 dB

1

1

2

2

3

3

4

4

PHASE

0/-180 DEG

0/-90 DEG

ROLL-OFF

ON

-2 dB

-4 dB

1

1

2

2

3

3

4

4

Bass

Roll-Off

Input

sensitivity

Position

A, B and D:

-2 dB

Suggested Tone Control

settings for a single subwoofer

Position C:

-6 dB

Note

Distance from front wall

Aligning the subwoofer

Subwoofer placement

D

D

AB

10 cm (4)

Main

speaker

110 cm (43)

60 cm (24) 60 cm (24)

10 cm (4) 10 cm (4)

Positioning too far from the wall may

cause a loss in low frequency response

C

1 Positions A and B are recommended.

2 Position C causes a significant bass

boost and may cause asymmetrical

spatial imaging if only one subwoofer is

used.

3 Recommended position for two linked

subwoofers is A+B. Positions C and D

may also work, but may cause loss of LF

when off room center axis.

4 LF mutual coupling causes a 6 dB

bass level increase when using two, 9.5

dB with three and 12 dB with four sub-

woofers.

C

Genelec Document BBAQSLSE001a. Copyright Genelec Oy 10.2006. All data subject to change.

7060B-7070A-7071A

Quick setup guide

Connection to the 6.1 bass management

Phase alignment

REDIRECT

SUM IN MODE

LFE BAND IDTH

120

85 TEST TONE

ON

LFE + 10 dB

REDIRECT

SUM IN MODE

LFE BAND IDTH

120

85 TEST TONE

ON

LFE + 10 dB

REDIRECT

SUM IN MODE

LFE BAND IDTH

120

85 TEST TONE

ON

LFE + 10 dB

LFE reproduced full range LFE reproduced up to 85 Hz LFE reproduced up to 120 Hz

Subwoofer Subwoofer

Subwoofer

85 Hz 85 Hz 120 Hz

1. Switch on the test tone

by setting dip switches 3

and 4 on the left switch

group to on. An 85 Hz

signal should be heard

from the subwoofer and

the monitor connected

to FRONT CENTER

channel.

5. Switch off the test

tone. Be sure to turn off

both switches to disable

the test tone.

Optional

slave subwoofer

SUM IN

input only

REDIRECT

SUM IN MODE

LFE BAND IDTH

120

85 TEST TONE

ON

LFE + 10 dB

ROLL-OFF

-4 dB

-2 dB

ON

PHASE

0/-180 DEG

0/-90 DEG

ROLL-OFF

-4 dB

-2 dB

ON

PHASE

0/-180 DEG

0/-90 DEG

ROLL-OFF

-4 dB

-2 dB

ON

PHASE

0/-180 DEG

0/-90 DEG

REDIRECT

SUM IN MODE

LFE BAND IDTH

120

85 TEST TONE

ON

LFE + 10 dB

2. Toggle the sub-

woofers dip switch 4 on

the right switch group

on and off and set it

to the position which

gives the lowest sound

level at the listening

position.

3. Toggle the sub-

woofers dip switch 3 on

the right switch group

on and off and set it

to the position which

gives the lowest sound

level at the listening

position.

4. Set dip switch 4 to

the opposite setting.

LCR

SL SC SR

LFE

Setting the LFE channel reproduction bandwidth

Center speaker

redirect on

Genelec Document BBAQSLSE001a. Copyright Genelec Oy 10.2006. All data subject to change.

GENELEC

Other manuals for 7060B

3

This manual suits for next models

2

Table of contents

Popular Subwoofer manuals by other brands

Sony

Sony XS-AW8 operating instructions

Sony

Sony XS-L836 Specifications

B&C Speakers

B&C Speakers 15 HPL 76W Specifications

Velodyne

Velodyne DD-18+ Specifications

Sonance

Sonance Cinema Series SUB 10-150 Specifications

Hifonics

Hifonics HW-12 Owners & installation manual

Magnat Audio

Magnat Audio ADR 130 BP user manual

Blitz

Blitz BZP106 Specifications

Technics

Technics SB-AS500 Operaing instructions

Lyngdorf

Lyngdorf BW-2 owner's manual

Lyngdorf

Lyngdorf BW-3 owner's manual

Pyle Pro

Pyle Pro PYLE PRO PDW15125 owner's manual

REL Acoustics

REL Acoustics Q Series operating instructions

Pioneer

Pioneer Elite S-W1EX Service manual

L-Acoustics

L-Acoustics KIVA SB15M Rigging manual

B&C Speakers

B&C Speakers Woofer 12 HPL 76 specification

KEF

KEF KUBE 200 installation manual

Yamaha

Yamaha SW500 owner's manual