Genaray Contender User manual
USER MANUAL
CONTENDER
LED FRESNEL SPOT FOCUSING LIGHT
Contender LED Fresnel Spot Focusing Light - USER MANUAL
2
THANK YOU FOR CHOOSING GENARAY
The Genaray Contender is a compact and versatile light
that’s ideal for still and tabletop photography, interviews,
and portraits. It features dense matrix LED technology that
furnishes a high-powered beam from a small array and
eliminates multiple shadows that are common in LED lighting.
It offers a brightness range of 100% to 10%, along with a high
CRI for precise color accuracy and rendering. The daylight
fixture’s color temperature is set to a constant 5600 K. The
bicolor fixture generates a color temperature range from 5600
to 3200 K that can be adjusted in 100 K increments for the
ideal color temperature to match other fixtures in the studio.
The integrated Fresnel lens allows the beam to be focused
from a concentrated 25° spot to a wide 55° flood. For
additional control, the barndoor attachment shapes the beam
while minimizing light spill. A tungsten filter is included with
the daylight fixture if a warmer light is needed, or to match
the color temperature of other tungsten-balance fixtures.
This compact and versatile light boasts an advanced
modular design that permits quick switching from AC
to DC power. The LED array generates minimal heat
so the fixture can be positioned close to subjects over
extended periods without burning or overheating them.
Contender
INTRODUCTION
Contender LED Fresnel Spot Focusing Light - USER MANUAL 3
· Please read and follow these
instructions, and keep this
manual in a safe place.
· Keep this unit away from water and
any flammable gases or liquids.
· Make sure the unit is powered off
when plugging it into a power source.
· Use only the correct,
recommended voltage.
· Do not attempt to disassemble or
repair the equipment—doing so will
void the warranty, and Genaray will
not be responsible for any damage.
· Handle the unit with care.
· Do not stare directly at the lights
when they are powered on.
· Clean the unit with only
a soft, dry cloth.
· All images are for illustrative
purposes only.
PRECAUTIONS
Precautions
Contender LED Fresnel Spot Focusing Light - USER MANUAL
4
CONTENDER
OVERVIEW
Control module (CB model shown)
Battery module
Battery slots
Battery contacts
Battery module
locking ring
Power switch
Control knob
LCD screen
Brightness
Color temperature
Battery power indicator
Contender LED Fresnel Spot Focusing Light - USER MANUAL 5
Product overview
AC input
Control module
locking ring
Main module
Heat vents
1/4 and 3/8 in.
threaded receivers
Focusing
ring
Barndoor lock
Barndoors
Insert slot
Arca-style
mounting plate
Contender LED Fresnel Spot Focusing Light - USER MANUAL
6
CONTENTS INCLUDE
CD
· Genaray CD Contender Daylight
LED Fresnel Spot Focusing Light
· Battery module
· NP-F750 li-ion battery (×2)
· Dual battery charger
· Charger power adapter
· AC power cord
· AC power adapter
· Ballhead mount
· Barndoors
· Tungsten filter
· User manual
· Carrying case
CD-3LK
· Genaray CD Contender Daylight LED
Fresnel Spot Focusing Light (×3)
· Battery module (×3)
· NP-F750 li-ion battery (×6)
· Dual battery charger (×3)
· Charger power adapter (×3)
· AC power cord (×3)
· AC power adapter (×3)
· Ballhead mount (×3)
· Barndoors (×3)
· Tungsten filter (×3)
· User manual
· Carrying case
contents
Contender LED Fresnel Spot Focusing Light - USER MANUAL 7
CB
· Genaray CB Contender Bicolor
LED Fresnel Spot Focusing Light
· Battery module
· NP-F750 li-ion battery (×2)
· Dual battery charger
· Charger power adapter
· AC power cord
· AC power adapter
· Ballhead mount
· Barndoors
· User manual
· Carrying case
CB-3LK
· Genaray CB Contender Bicolor
LED Fresnel Spot Focusing Light (×3)
· Battery module (×3)
· NP-F750 li-ion battery (×6)
· Dual battery charger (×3)
· Charger power adapter (×3)
· AC power cord (×3)
· AC power adapter (×3)
· Ballhead mount (×3)
· Barndoors (×3)
· User manual
· Carrying case
contents
Contender LED Fresnel Spot Focusing Light - USER MANUAL
8
USING THE CONTENDER
WITH BATTERY POWER
Important!
The Contender will operate only
with both batteries installed.
To attach the battery module to the
Contender, follow these steps:
1. Unscrew the control module locking
ring, and remove the control module.
2. Align the power contacts of the battery
module with the contacts on the main
module, and connect the two modules.
3. Tighten the battery module
locking ring until secure.
4. Attach the control module to the
battery module by aligning the contacts
and tightening the locking wheel.
POWERING THE
CONTENDER
USING THE CONTENDER
WITH AC POWER
Important!
The Contender is a multivoltage fixture
capable of running on 100–240 V, 50/60 Hz.
The included cable has a 120 V, 50 Hz
(North American) plug. To use this fixture
with other voltages, you must use a
plug adapter (sold separately).
Make sure the unit is turned off. Connect
the AC power adapter to the Contender's
AC input, and insert it in until secure.
instructions
Contender LED Fresnel Spot Focusing Light - USER MANUAL 9
5. Insert the batteries by aligning the
battery contacts and pressing the
batteries down into the battery slots.
CHARGING THE BATTERIES
Insert the batteries into the dual
battery charger, and plug the
charger into a wall outlet.
The indicator lights on the charger will
show the remaining charge in each
battery, and the lights will blink to
indicate that charging is in progress.
When all indicator lights are steadily
illuminated, the batteries are fully charged.
instructions
Contender LED Fresnel Spot Focusing Light - USER MANUAL
10
MOUNTING THE
CONTENDER
The Contender can be mounted directly to
a light stand, a tripod head with an Arca-
style clamp, or the included ball head.
LIGHT STAND
The Contender is equipped with
1/4- and 3/8-inch threaded receivers.
To mount the contender directly to a
light stand, screw the Contender onto
the light stand’s threaded post.
ARCA-STYLE CLAMP
Loosen the locking knob of the Arca-
style clamp and slide the Contender’s
mounting plate into the clamp. Tighten
the locking knob until the Contender is
secure and doesn’t move in the clamp.
BALLHEAD
Screw the ballhead onto the light stand.
Note: The ball head comes with a 3/8- to
1/4-inch adapter bushing installed. If your
light stand has a 3/8-inch threaded post,
remove the bushing to attach the ballhead.
Screw the ballhead’s 1/4-inch
post into the Contender.
Make sure the ballhead’s locking
handle is securely tightened before
you let go of the Contender.
Ballhead feature: The locking handle
is a ratchet-style handle. If you are
using the ballhead in a tight space that
doesn’t allow you to fully rotate the
handle, pull the handle out, reposition
it, and let it snap back into place.
instructions
Table of contents
Other Genaray Dj Equipment manuals
