Gefen USB-200 User manual
USB•200
USER MANUAL
www.gefen.com
ASKING FOR ASSISTANCE
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday.
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff St.
Chatsworth, CA 91311
www.gefen.com
© 2007 Gefen Inc., All Rights Reserved
Notice
Gefen Inc. reserves the right to make changes in the
hardware, packaging and any accompanying documentation
without prior written notice.
USB•200 is a trademark of Gefen Inc.
ExtremeUSB is a trademark of Icron Inc.
Macintosh is a trademark of Apple Computer Inc.
TABLE OF CONTENTS
General Information
Introduction........................................................1
Operation Notes.................................................2
USB Series Installation .....................................3
USB•200 Panel Layout .....................................4
USB•200 Function Description ..........................5
Wiring Diagram .................................................6
Link Cable Diagram ..........................................7
Check List .........................................................8
Troubleshooting Hints........................................9
Warranty ........................................................10
Thank you for purchasing the ex•tend•it USB•200 Series.
Incorporating ExtremeUSB, the new USB•200 model allows
users the benefits of USB technology beyond the desktop,
extending your computer keyboard, mouse, trackball, and
any USB device up to 330 feet away from the location of
your Macintosh or PC computer.
The USB•200 system consists of two units: the
USB•200S Sender resides next to the host computer, and
the USB•200R Receiver resides next to the extended USB
devices.
The USB•200 signal controls the keyboard, mouse,
trackball and other USB devices by buffering the keyboard/
mouse signal through send and receive line drivers, and the
signal is extended by using standard Category 5 (CAT-5)
cabling.
You can connect additional USB•200 setup to the same
computer, allowing you to access the computer from multiple
locations up to 330 feet apart.
INTRODUCTION
1
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE USB•200 SYSTEM.
* The USB•200 send and receive were designed to operate
on USB type computers. DO NOT attempt to use this
equipment with any other type computers.
* Use the computer's USB port when using a local keyboard
that is not extended with the USB•200 sender unit.
* In order to operate properly, the USB•200 receiver unit
must be connected, powered up, and the CAT-5 cable
installed between the send and receive.
* Only dedicated Category 5 UTP type cable (CAT-5) is
recommended for this application (pin to pin).
* The length of cable used to connect the USB•200S send
unit to the USB•200R receiver unit MUST NOT EXCEED
330 feet.
Includes:
(1) USB 200 Sender and Receiver
(1) 6' USB Cable A-B
(1) 5VDC Power Supply
(1) Users Manual
2
USB•200 SERIES INSTALLATION
1. Place the USB•200R unit close to the USB devices at the
remote end.
2. Connect the USB devices to the USB•200R unit.
3. Connect the power adapter to a suitable AC source wall
outlet.
4. Connect the power adapter to the USB•200R unit using
the supplied cable.
5. Place the USB•200S unit close to the host computer.
6. Connect the USB•200S unit to the USB•200R unit using
the desired length of CAT5 cable
7. Connect the USB•200S unit to the host computer using
the USB cable supplied with the unit .
This connection should be made last.
3
USB•200S
USB•200R
USB•200S&R
1 2 3
USB•200 PANELS LAYOUT
4
USB IN
CAT-5
USB
76
5
ON
8
4
5V
9 10
Power LED
Indicates the unit is receiving power from the computer
USB In
USB from computer
Active
Indicates if a USB device is active at the receiver
Active
Indicates if the USB port on the computer is active
Link
CAT-5 Modular Jack which connects to the USB•200S
send and the USB•200R Receive units
Power LED
Indicates the unit is plugged in and powered up.
DC In
Power plug for 5VDC wallmount power supply.
USB input A
Two USB A type connector hub
Active
Indicates if a link between the USB•200S send and the
USB•200R Receive units
Active
Indicates if a USB device is active at the receiver
1
3
4
5
6
8
9
10
2
USB•200 FUNCTION DESCRIPTION
7
5
WIRING DIAGRAM
6
USB•200
receiver/HUB
USB•200
sender
USB 1
Up to 330 feet away
USB 2
LINK CABLE - WIRING DIAGRAM
7
White/Or-
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
RJ-45 Jack RJ-45 Jack
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
1818
This manual suits for next models
2
Table of contents
Other Gefen Extender manuals
Gefen
Gefen EXT-HD-CP-FM10 User manual
Gefen
Gefen EXT-FW-1394BP User manual
Gefen
Gefen EXT-UHD-CAT5-ELRPOL User manual
Gefen
Gefen ToolBox GBT-HDBT-POL User manual
Gefen
Gefen EXT-DVIKVM-ELR User manual
Gefen
Gefen HDMI CAT-5 IR User manual
Gefen
Gefen MS User manual
Gefen
Gefen Toolbox GTB-HDMI-3DTV User manual
Gefen
Gefen EXT-DVIKA-HBT2 User manual
Gefen
Gefen Toolbox GTB-HDMI-3DTV User manual
Gefen
Gefen EXT-USB-MINI2N User manual
Gefen
Gefen EXT-DVI-2CAT6DL User manual
Gefen
Gefen ToolBox GTB-USB2.0-4LR User manual
Gefen
Gefen EXT-COMP-141N User manual
Gefen
Gefen EXT-UHD600-1SC User manual
Gefen
Gefen FW-1394 User manual
Gefen
Gefen CAT5-9000I User manual
Gefen
Gefen EXT-HDMI1.3-1FO User manual
Gefen
Gefen EXT-UHDV-KA-LANS-TX User manual
Gefen
Gefen GTV-WHDMI User manual
