Gefen HD-1000 User manual
HD-1000
Extender
Model # EXT-HD-1000
USER MANUAL
www.gefen.com
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday through Friday.
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff Street
Chatsworth, CA 91311
www.gefen.com
Notice
Gefen Inc. reserves the right to make changes in the hardware, packaging
and any accompanying documentation without prior written notice.
HD-1000 is a trademark of Gefen Inc.
HDMI is a trademark of HDMI.org
© 2008 Gefen Inc., All Rights Reserved
ASKING FOR ASSISTANCE
TABLE OF CONTENTS
Introduction / Operation Notes1.
Features2.
Sender Panel Descriptions3.
Receiver Panel Descriptions4.
Connecting and Operating the HD-10005.
Network Cable Wiring Diagram6.
Specifications7.
Warranty8.
The Gefen HD-1000 allows an HDMI video signal to be extended up to 330
feet (1640 w/o HDCP) using multi-mode LC-LC fiber optic cable. Fiber Optics
technology allows the HD-1000 to carry video signals over long distances that
are not possible with other technologies. Fiber Optic cables are immune to video
signal corruption from electromagnetic interference (EMI), ensuring a crystal
clear picture.
How It Works
The HD•1000S sender unit sits next to your set-top box or DVD player source.
Cables supplied with the HD•1000 connect your HDMI™ 1.3 source to the
sender unit. The display plugs into the back of the receiver unit. One CAT-5 cable
and a multi mode LC fiber optic cable connect the Sender and the Receiver units
to each other.
INTRODUCTION
1
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE HD-1000
50 or 62.5 micron multi-mode fiber optic cable is required for operation of the• HD-1000.
Maximum extension range of 330 feet (100 meters) when the source• requires HDCP. One CAT-5, CAT-5e or CAT6 cable is used to transmit DDC
and HDCP data back to the source.
Maximum range of 1640 feet (500 meters) when the source does not require• HDCP. This scenario does not require the CAT-5, CAT5e or CAT-6 cable if
the source does not require DDC information. If DDC is required, the use of
an EDID storage device (part# EXT-DVI-EDIDN, EXT-DVI-EDIDP) can be
used to transmit DDC information back to the source.
HDMI 1.3 compliant (please see FEATURES section on page 2 for• supported HDMI 1.3 features).
HDCP compliant•
Compatible with all HDMI and DVI* displays.•
NOTE: *When used with a DVI to HDMI adapter
OPERATION NOTES
FEATURES
Features
Extends high definition HDMI compliant devices up to 330 feet (100 meters)•
Uses a 4 strand multi mode LC-LC fiber optic cable for HDMI and a CAT5e cable for• DDC/control signals
Extends range of HDMI by equalizing signals•
HDCP and HDMI compliant with HDMI 1.3 Features•
Supports resolutions up to 1080p, 2K, and 1920 x 1200•
HDMI 1.3 Supported Features
12-bit/channel RGB Deep Color support•
CEC protocol support•
Lip-Sync pass-through•
Dolby TrueHD, DTS-HD pass-through•
xvYCC pass-through•
Includes:
(1) HD-1000S Sender unit
(1) HD-1000R Receiver unit
(2) 5V DC Power Supply
(1) 6 ft HDMI cable (M-M)
(1) User’s Manual
2
SENDER PANEL DESCRIPTIONS
Back Panel
Front Panel
Power LED
Indicator
RJ-45
Port
HDMI Input
Port
Fiber Optic
LC-LC Terminals
Status LED
Indicator
5V DC
Power Input
3
RECEIVER PANEL DESCRIPTIONS
Back Panel
Front Panel
Power LED
Indicator
RJ-45
Port HDMI Input
Port Fiber Optic
LC-LC Terminals
Status LED
Indicator
5V DC
Power Input
4
CONNECTING AND OPERATING THE HD-1000
How To Connect The HD-1000
Connect the HDMI source to the HD-1000 sender unit using the supplied HDMI1. cable.
Connect a user supplied CAT-5, CAT-5e or CAT-6 cable to the sender unit.2.
Connect four user supplied multi-mode LC terminated fiber optic cables into3. HD-1000 sender unit.
NOTE: 50 or 62.5 micron multi-mode fiber optic cable is required for operation of
the HD-1000.
Connect the other end of the CAT-5, CAT-5e or CAT-6 cable into the HD-4. 1000 receiver unit.
Connect the other ends of all four multi-mode LC terminated fiber optic5. cables into the HD-1000 receiver unit.
NOTE: Please take careful note of the labeling above each fiber optic port on
both the sending and receiving HD-1000 units. The most common user error is
to mis-match the fiber optic cable connections on each end, which results in no
video being transmitted.
Connect the display to the HD-1000 receiver unit using a user supplied6. HDMI cable.
Connect the included 5V DC power supplies into both the HD-1000 sending7. unit and receiving units.
Power on the display, followed by the source.8.
No further adjustments are necessary to operate the HD-1000.
5
NETWORK CABLE WIRING DIAGRAM
12345678
Gefen has specifically engineered their products to work with the TIA/EIA-568-B
specification. Please adhere to the table below when field terminating cable for
use with Gefen products. Failure to do so may produce unexpected results and
reduced performance.
CAT-5, CAT-5e, and CAT-6 cabling comes in stranded and solid core types.
Gefen recommends using solid core cabling. CAT-6 cable is also recommended
for best results.
Each cable run must be one continuous run from one end to the other. No splices
or use of punch down blocks.
Pin Color
1 Orange / White
2 Orange
3 Green / White
4 Blue
5 Blue / White
6 Green
7 Brown / White
8 Brown
6
This manual suits for next models
1
Table of contents
Other Gefen Extender manuals
Gefen
Gefen Firewire 800 User manual
Gefen
Gefen EXT-AUD -1000 User manual
Gefen
Gefen USB-2.0 User manual
Gefen
Gefen EXT-DVIKVM-LAN-L User manual
Gefen
Gefen CAT5-7500 User manual
Gefen
Gefen EXT-HDMI1.3-CAT5-ELR User manual
Gefen
Gefen USB-MIDI User manual
Gefen
Gefen ex-tend-it CAT5-1000 User manual
Gefen
Gefen EXT-HDMI1.3-1CAT6 User manual
Gefen
Gefen EXT-VGAKVM-LAN User manual
Gefen
Gefen EXT-COMPOS ITE -141N User manual
Gefen
Gefen GBT-HDBT-POL User manual
Gefen
Gefen EXT-COMPAUD-141 User manual
Gefen
Gefen EXT-CAT5-1600A User manual
Gefen
Gefen CAT5-3000 User manual
Gefen
Gefen EXT-2DVI-DLKVM-CAT6 User manual
Gefen
Gefen USB 2.0 LR Extender EXT-USB2.0-LR User manual
Gefen
Gefen CAT5-8000 User manual
Gefen
Gefen EXT-HDMIRS232-CAT5 User manual
Gefen
Gefen ex-tend-it CAT5-1500 User manual
