Geevon W2186113 User manual
Press button to confirm your setting, the month display starts to
flash, use or buttons to set the correct month.
Press button to confirm your setting, the date display starts to
flash, use or buttons to set the correct date.
Press button to confirm your setting, the language start to flash,
use or buttons set the correct language. The language order
is: ENG, GER, FRE, ITA, DUT, SPA, DAN.
Press button to confirm your setting and to end the setting
procedures, enter the normal mode.
NOTE: You will automatically exit settings mode if no buttons are
pressed for 20 seconds. Enter settings mode again at any time by
pressing and holding button for 2 seconds.
Under normal mode, press button to enter alarm mode.
Setting the Alarm:
a. Press button to enter alarm mode, press and hold button
for about 2 seconds to set the alarm time. The alarm hour will begin
blinking on the display where the clock time is usually shown.
b. To adjust the alarm hour, press the or buttons (press and
hold to fast adjust). When alarm hour is set to your satisfaction,
press button to proceed to the alarm minute preference. Press
the or buttons (press and hold to fast adjust), press
button again to exit alarm settings. When you setting the alarm, the
alarm is default turn on.
c. To turn the alarm ON or OFF, press button to enter alarm mode,
press the or button to ON or OFF the alarm. The “ ” symbol
should show next to the clock display when alarm is set to ON. Press
the or button again to turn off the alarm, when the alarm is set
to OFF, the “ ” symbol should not display.
d. When the alarm is in operation it will begin beeping with one short
beep and continue with many short beeps if the alarm rings longer
than 20 seconds. You can snooze the alarm for 5 minutes by pressing
the SNZ/LIGHT button.
Indoor / outdoor temperature and humidity
1. Indoor temperature -9.9°C ~ 50°C (13.9°F ~ 122°F), display LL.L
when below -9.9°C and display HH.H when higher than 50°C.
2. Outdoor temperature -40°C ~ 70°C (-40°F ~ 155°F), display LL.L
when below -40°C and display HH.H when higher than 70°C.
3. Temperature resolution: 0.1°C
4. Indoor and outdoor humidity range: 20%-95%, display 20% when
below 20% and display 95% when higher than 95%.
6. Humidity resolution: 1 %RH
7. When alarm ringing, temperature and humidity test will be stopped.
Accuracy
1. Temperature accuracy:
-40°C ~ -20°C: ± 4°C
-20°C ~ 0°C: ± 2°C
0°C ~ +50°C: ±1°C
Note: when the temperature in 50°C ~ 70°C range, the temperature is
only for reference.
2. Humidity accuracy: +/- 5 % RH (@25°C , 30%RH to 50%RH);
+/- 10 % RH (@25°C , 20%RH to 29%RH, 51%RH to 95%RH)
Temperature alert set
1. In standard mode, press to enter alert mode, use or to
open or close temperature alert function.
2. In standard mode, press and hold to set temperature alert
function.
3. Press to set and order is: outdoor temperature upper limit→
outdoor temperature lower limit→ outdoor humidity upper limit→
outdoor humidity lower limit→ indoor temperature upper limit→ indoor
temperature lower limit→ indoor humidity upper limit→ indoor
humidity lower limit→ exit.
4. In set, press to go ahead by once. Hold to go ahead at 8
steps per second.
5. In set, press to back by once. Hold to go back at 8 steps
per second.
6. Press or no handling in 10s will exit.
Temperature alert
1. Temperature and alert icon will flash when alert.
GEEVON Touch Screen Weather Station
User Manual
Model No: W2186113
Package Contents:
1. Display Unit
2. Outdoor Sensor
3. Instructions Manual
Installing or Replacing Batteries:
We recommend using high quality batteries for the best product
performance. Heavy duty or rechargeable batteries are not
recommended. The outdoor sensor requires lithium batteries in low
temperature conditions. Cold temperatures can cause alkaline
batteries to function improperly.
Do not mix old and new batteries. Do not mix alkaline,
standard, and/or rechargeable batteries.
Default settings
1. Default time: 12:00 (Time form: 12H)
2. Default date: 01/01 (Year: 2020, date form: M/D)
3. Default week: WED (Language: ENG, 7 languages can be
selected)
4. Weather forecast: Partly Sunny
5. Default temperature: ℉
6. Default alarm: AM 12:00, default snooze time: 5min.
The LCD display fully for 10 seconds when changing new battery or
resetting, then with a sound BI into the normal state, after testing
temperature, receiving RF for 3 minutes.
Display / Keys Details:
There are totally 6 keys for the alarm clock, they are included: ,
, , , , , SNZ/LIGHT
1. buttons:
a. Press and hold for 3 seconds during normal mode to enter setting
mode.
b. Press button during normal mode to enter alarm mode.
2. button:
a. Press button to select the channel.
c. In normal display mode, press and hold to search RF.
3. button
a. Press the button to enter alert mode, use or to open
or close alert.
b. Press and hold the button to enter alert setting.
4. button:
a. Press to decrease the setting value during setting.
b. Press and hold 2 seconds button for fast adjust during setting mode.
c. In normal display mode, press button to display max/min
temperature/humidity.
d. Press and hold the button 2 seconds to clear the record of
MAX/MIN temperature and humidity when display shows MAX or
MIN temperature and humidity.
5. buttons:
a. Press to increase the setting value during setting.
b. Press and hold 2 seconds button for fast adjust during setting mode.
c. In normal display mode, press button to display heat
index/dew point.
6. SNZ/LIGHT button:
a. Press this button to open backlight for 10 seconds
b. Press to activate the snooze function when alarming
c. Press this button to open backlight.
Manually Setting the Time, Date & Units:
Press and hold down the button for 2 seconds the 12/24 hour
mode starts to flash, use and buttons to set the correct 12/24
hour mode.
Press button to confirm your setting, the hour display starts to
flash, use or buttons to set the correct hour.
Press button to confirm your setting, the minute display starts to
flash, use or buttons to set the correct minute.
Press button to confirm your setting, the Month and Date icon
display starts to flash, use or buttons to set the date display
on Month/Date or Date/Month
Press button to confirm your setting, the year display starts to
flash, use or buttons to set the correct year.
Features & Benefits:
DISPLAY UNIT & OUTDOOR SENSOR
1.Heat index/dew point
2.Channel external sensor
3.Outdoor temperature max/min record
4.Outdoor sensor signal strength
5.Outdoor temperature alert
6.Outdoor humidity
7.Tendency of outdoor temperature
8.Low battery indicator
9.Indoor humidity
10.Icons of weather forecast
11.Outdoor temperature
12.Indoor humidity alert
13.Indoor temperature alert
14.Indoor temperature
15.Tendency of indoor temperature
16.Calendar
17.Weekday
18.Alarm and snooze icons
19.Time display
20. :MODE button
21. :RF button
22. :ALERT button
23. :DOWN button
24. :UP button
25.Wall mount hole
26.SNZ/LIGHT button
27.Battery Compartment
28.Wireless signal indicator (Flashes when data is being sent to the
display unit)
29.Integrated hang hole
30.Compartment 2xAAA batteries (batteries not included)
31.TX channel selector, select external sensor channel (Maximum 3
channels available)
Moon Phase
Placement of the Device:
Proper placement of both the display unit and the outdoor sensor
are critical to the accuracy and performance of this product.
Display Unit Placement
Place the display unit in a dry area free of dirt and dust. Display unit
stands up right for tabletop/countertop use.
Important Placement Guidelines
a. To ensure accurate temperature measurement, place units out of
direct sunlight and away from any heat sources or vents.
b. Display unit and outdoor sensor must be within 200ft (60m) of
each other.
c. To maximize wireless range, place units away from large metallic
items, thick walls, metal surfaces, or other objects that may limit
wireless communication.
d. To prevent wireless interference, place both units at least 3ft (1 m)
away from electronic devices (TV, computer, microwave, radio, etc.
Outdoor Sensor Placement
a. The sensor must be placed outside to observe outdoor
conditions. It is water resistant and designed for general outdoor
use, however, to prevent damage place the sensor in an area which
is protected from the direct weather elements and direct sunshine.
The best location is 4 to 8 feet above the ground with permanent
shade and plenty of fresh air to circulate around the sensor.
b. Display unit and outdoor sensor must be within 100 feet of each
other.
c. In order to maximize the wireless range, place units away from
large metallic items, thick walls, metal surfaces or other objects that
may limit wireless communications.
d. To prevent wireless interferences, place both units at least 3 feet
away from electronic devices (EX: TV, computer, microwave etc.)
Outdoor Sensor Function:
a. Once the display unit has been set up and the channel
synchronized with the outdoor sensor, the display unit will begin the
registration process. It can take up to 3 minutes to complete the
registration, where the display unit will search for an RF (Radio
Frequency) signal from the outdoor sensor. The outdoor sensor
signal strength will show the connection strength to the outdoor
sensor. If there are no bars or if bars are not showing at its
maximum strength (4 bars) (3) try placing the outdoor sensor or
display unit elsewhere for better connection.
b. If the RF Signal was lost and not reconnected, the outdoor
temperature and humidity level will begin to flash after 1 hour of lost
connection. If no connection was found after 2 hours only a dotted
line ‘ - - - ’ will be displayed in place of the temperature and humidity
level.
c. To manually restart the RF registration, press and hold button
for 3 seconds. The display unit will now search for the RF signal for
the next 3 minutes.
Week Display
2. In temperature alert status, alert temperature icon will twinkle and
temperature will always display.
3. Temperature alarm sound:
a. Two BIs /second
b. Alarm 5s for every minute
c. Not stop alarm until meet stop conditions.
4. Alarm stop conditions：
a. Press any button to stop alarm but temperature and alert icon will
continuously flash.
b. When temperature go back into alert range.
c. Press to enter alert mode, use or to turn off the
temperature alert function.
Setting the Temperature Units:
a. The default temperature unit is Fahrenheit (°F).
b. To switch to Celsius, press and hold button. You will see 12/24
hour mode flashing.
c. Press button 8 more times to scroll through the other settings.
You will see °F flashing.
d. Press or to switch from Fahrenheit to Celsius.
e. Press to confirm your selection and exit.
Checking the MAX/MIN temperature and humidity
a. Press button to check MAX/MIN temperature and humidity.
b. Press and hold 2 seconds button to clear the record of
MAX/MIN temperature and humidity when display shows MAX or
MIN temperature and humidity.
Setting the Channel:
Setting the channel connection between the display unit and outdoor
sensor:
a. To change the channel on the display unit between 1, 2, 3 &1-3
sequential display, press button. The channel setting will display
on the above of the outdoor temperature.
b. To change the channel option on the outdoor sensor open the
battery compartment cover, on the upper left side is a button.
c. ALWAYS MAKE SURE THE CHANNEL CHOSEN ON THE
DISPLAY UNIT MATCHES THE CHANNEL OPTION CHOSEN ON
THE OUTDOOR SENSOR.
Back Light:
When the display unit is powered by battery only the back light will
be off to preserve the battery. Press the SNZ/LIGHT button to turn
the back light on for 10 seconds.
Low Battery Indicator:
If the low battery indicator is displayed on the LCD for either the
outdoor sensor or the display unit, immediately change the batteries
to prevent disruptions in communications of the devices.
Weather Forecast:
a. The unit predicts weather condition of the next 12-24 hours based
on the change of temperature and humidity. Weather change
parameters: (this product is not pressure function, so the weather
forecast is according to the outdoor temperature and humidity
change indicator) now the product change the weather according to
the channel 1 temperature and humidity change, if the channel 1 did
not receive the signal, the weather according to the indoor
temperature and humidity.
The following are icons that will show:
NOTE:
a. The weather forecast is based on outdoor temperature and
humidity change and is about 40-45% correct.
b. The weather forecast can be more accurate only under the
condition of natural ventilation, in indoor conditions, especially in
air-conditioned rooms, there will be not accurate.
Web: www.geevon.com
E-mail:[email protected]
Prolinx GmbH MADE IN CHINA
Brehmstr.56,40239 Duessldorf
Germany
EC REP
TV
(200 feet maximum)
(60 meters)
(0.9 m)
3feet
AT
LEAST
APART
Problem Possible Solution
Outdoor reading
is flashing or
showing dashes
No outdoor
sensor reception
Inaccurate
temperature
"HH/LL" display
in indoor and/or
outdoor
temperature
Flashing of the outdoor reading is
generally an indication of wireless
interference. This thermometer is
arranged to communicate with three
external sensors. One of these comes
with the unit, the remaining two are
optional.
1. Bring both of the sensor and display
indoors, side by side and remove
batteries from each. Power the
thermometer as described in Getting
started.
2. Set the selector in the outdoor sensor
to the desired transmission channel (1,
2, or 3). Automatic data will be
transmitted.
3. Press the CH button more times to
select the channel set on the external
sensor. Sequentially selects channel 1,
channel 2, channel 3, and sequentially
display for 3 channels.
1. Reload the batteries of both outdoor
sensor and main unit.
Please refer to the SENSOR SETUP
section.
2. Press and hold the CH button to
receive RF signal.
3. Always make sure the channel chosen
on the display unit matches the channel
option chosen on the outdoor sensor.
4. Relocate the main unit and/or the
outdoor sensor. The units must be within
200ft (60m) of each other.
5. Make sure both units are placed at
least 3 ft (1m) away from electronics
that may interfere with the wireless
communication (such as TV, microwave,
computer, radio, etc).
6. Do not use heavy duty or
rechargeable batteries. The outdoor
sensor requires lithium batteries in low
temperature conditions. Cold
temperatures would cause alkaline
batteries work improperly.
7. Do not mix old and new batteries.
1. Make sure both the main unit and
sensor are placed out of direct sunlight
and away from any heat sources or
vents.
2. Do not tamper with the internal
components.
3. Temperature accuracy:
(-40°C ~ -20°C)：±4°C
(-20°C~0°C)：±2°C
(0°C~50°C):±1°C
If the temperature is higher than the
detection range, HH will display on
screen for indication; if lower than the
detection range, LL will display on
screen for indication.
If your Geevon product does not operate properly after
trying the troubleshooting steps, contact the seller on
your order page or shoot an email to :
Trouble Shooting:
Sunny Partly sunny Cloudy Rainy Snowy
Other Geevon Weather Station manuals
Popular Weather Station manuals by other brands
National Geographic
National Geographic VA Colour RC instruction manual
Renkforce
Renkforce 1208067 operating instructions
Levenhuk
Levenhuk Discovery Report WA40 quick start guide
Instant Transmission
Instant Transmission MA 10410 instruction manual
Lutron Electronics
Lutron Electronics PHB-318 Operation manual
WAREMA
WAREMA EWFS Weather station eco Operating and installation instructions