Geemarc Dallas 10 User manual
DD
DD
DALLAS 10ALLAS 10
ALLAS 10ALLAS 10
ALLAS 10
Userguide
Telephone
If you are using this telephone with a hearing aid, set your
hearing aid to the «T» setting
T.B.A.
SETTING UP
(*) Classified TNV-3 according to EN60950 standard.
1-CONNECTINGTELEPHONE
1 - Connect the handset cord.
2 - Connect the line cord to the socket located
at rear of telephone then connect the PTT plug*.
T.B.A.
Drawingdescription
SETTING UP
2-RINGER SETTINGS
A switch located on right side allows the ringer to
be switched On ( ) or Off ( ).
3 - WALLMOUNTING
Towall-mountyourtelephone,slideouttheclipturn
aroundandslidebackintothewallmountingposi-
tion (located in the base unit, just below the ear
piece).Thiswillensurethatthehandsetstaysfirmly
in position. Make 2 holes in the wall 85mm apart,
insertthewallplugsandthewallmountingscrews.
Thescrewsshouldprotrudefrom wallby 6-7mm.
Place the phone onto the screw-heads and slide
down to secure.
4 - TONE/PULSE SWITCH (T/P)
The Tone/Pulse switch is factory pre-set to Tone
position(T).IntheUK,alltelephoneexchangesnow
useTonedialing. Ifyourphonedoesnotdialoutit
isprobablybeingusedfromanolderprivateswitch
board (PBX). In this case, the Tone/Pulse switch
must be moved to Pulse (P).
USING THE PHONE
1-ANSWERINGINCOMINGCALL
-Whenanincomingcallisreceivedthephonewill
ring and flash. To answer the call lift the handset
andspeak.
- On completion of the call, carefully replace the
handset in the cradle to release the line.
2-VOLUME RECEIVINGADJUSTMENT
You can increase the volume according to your
ownhearingrequirements.
Use the VOL button, located on the right side, to
adjust the level according to your own hearing
requirements.
VOL
0dB +15dB
USING THE PHONE
3 - MAKINGACALL
- Lift the handset.
-Awaitthe dial toneand dial required number.
- On completion of the call, carefully replace the
handset in the cradle.
4-SENDING LEVELADJUSTMENT
Ifyourvoiceisquietorcalledpartieshavedifficulty
hearing you, you can increase the sending level
volume with the switch located on the right
side.
5- LAST NUMBERREDIAL
- Lift the handset.
-Await the dial tone and press button.
-Thepreviouslydiallednumberwillbeautomaticaly
redialled(notinuseformemorynumbers).
0dB +4dB
USING THE PHONE
6 - R, * & # BUTTONS
Theseareusedwiththenewservicesprovidedon
digitalexchanges.Fordetailspleasecontactyour
network operator.
7-STORINGTELEPHONENUMBERS
Your phone can store 3 direct and 10 indirect
memories(16digitsmaximumforeach memory).
- Lift the handset.
- Press button.
- Dial the telephone number you wish to store.
- Press button.
-Pressoneofthedirectmemorybuttons,M1,M2,
M3.
Or press MEM and any button 0 to 9 on the key
pad under which you wish to store the telephone
numberinindirectmemory.
- Replace the handset.
USING THE PHONE
Note: Numbers willbe lost ifyou disconnect your
phone. Entering a new number in memory will
automaticallyerasethe previousnumber.
8-DIALLING STOREDNUMBER
- Lift the handset and await the dial tone.
-PressappropriatedirectmemorybuttonM1, M2,
or M3. The stored number will be dialled out
automatically.
OrpresstheMEMbuttonfollowedbythekeypad0
to 9 button under which the desired number is
stored. The stored number will be dialled out
automatically.
To register your stored phones numbers, use the
index located on the base.
GUARANTEE
Fromthe momentyour Geemarcproduct ispurchased, Geemarc
guaranteeit fortheperiodofoneyear. During thistime,allrepairs
or replacements (at our option) are free of charge.Should you
experienceaproblemthencontactourhelplineorvisitourwebsite
at www.geemarc.com.The guarantee does not cover accidents,
negligence or breakages to any parts. The product must not be
tamperedwithor takenapart byanyonewho isnot anauthorised
Geemarcrepresentative.TheGeemarcguarantee innowaylimits
yourlegalrights.
IMPORTANT:YOURRECEIPTISPARTOFYOURGUARANTEE
AND MUST BE RETAINED AND PRODUCED IN THE EVENT
OFAWARRANTYCLAIM
Please note:The guaranteeapplies totheUnitedKingdomonly.
Declaration : Hereby Geemarc Telecom SA declares that this product is in
compliance with the essential requirements and other relevant provisions of
theRadioandTelecommunicationsTerminalEquipmentDirective1999/5/EEC
and in particular article 3 section 1a, 1b and section 3.
Telephone connection : Voltagespresent on thetelecommunicationnetwork
are classified TNV-3 (Telecommunication Network Voltage) according to the
EN60950standard.
For product support and help visit our website
at www.geemarc.com
telephone 01707 384438
or fax 01707 372529
UGDAL10 ED01
Other manuals for Dallas 10
1
Table of contents
Other Geemarc Telephone manuals
Geemarc
Geemarc Amplidect Combi-Photo 295 Instruction manual
Geemarc
Geemarc CL8350 Mounting instructions
Geemarc
Geemarc AmpliPOWER 40 User manual
Geemarc
Geemarc amplidect 295 photo User manual
Geemarc
Geemarc Ampli1100 User manual
Geemarc
Geemarc CL555 User manual
Geemarc
Geemarc AMPLI600 User manual
Geemarc
Geemarc DALLAS 100 VM User manual
Geemarc
Geemarc MAYFAIR User manual
Geemarc
Geemarc PHOTOPHONE 450 User manual
Geemarc
Geemarc Dallas 30 User manual
Geemarc
Geemarc combi dect 295 User manual
Geemarc
Geemarc AmpliPOWER 40 User manual
Geemarc
Geemarc CL8350 User manual
Geemarc
Geemarc CL200+ User manual
Geemarc
Geemarc Ampli500 User manual
Geemarc
Geemarc COMBI DECT 295 Photo User manual
Geemarc
Geemarc APOLLO 10 User manual
Geemarc
Geemarc MARBELLA User manual
Geemarc
Geemarc DALLAS 100 VM User manual
