Geeetech Mizar S User manual
V1.0
USER MANUAL
Mizar S
Shenzhen Getech Technology Co., Ltd.
www.geeetech.com
TERMS
Please be advised of the following terms (the “Terms”) regarding this User Manual (this “Manual”):
All information in this Manual is subject to change at any time without notice and is provided for convenience purposes only. GEEETECH reserves the
GEEETECH Support Team for up-to-date information.
DISCLAIMERS
Neither GEEETECH
particular purpose, or non-infringement of intellectual property. To the fullest extent permissible by the applicable law, we hereby disclaim all liability
compliance with any codes, or misappropriation. To the fullest extent permissible by the applicable law, we hereby disclaim any and all responsibility,
risk, liability, and damages arising out of death or personal injury resulting from assembly or operation of our products. GEEETECH assumes no respon
sibility, nor will be liable, for any damages to, or any viruses or malware that may infect your computer, telecommunication equipment, or other
property caused by or arising from your downloading of any information or materials related to GEEETECH products.
CONTACT US
After-sales E-mail
Rita technical <technical@geeetech.com>
Technical support
Technical support
1. Warm Tips
2. Packing List
3. The Whole Machine Structure Inspection
4. Check Power Supply
5. Machine Components
7. Connect Cables
8. Touch Screen UI Introduction
6. Assemble the Machine
1
2
3
4
5
6
8
9. Hot Bed Leveling 14
10. Loading Filament 18
9
CONTENTS
11. Start Printing
12. Parameter Adjustment After Printing Starts
14. Break-Resuming
13. Pause Printing
15. Filament Detector
17. Online Printing
18. Daily Maintenance and Usage Suggestions
16. Slicing Software
19
20
21
21
22
22
23
19. FAQ 24
20. Wiring diagram & Machine Parameters 26
21
1
WARM TIPS
After unpacking, please check whether the accessories are complete or not. If any accessories are missing, please contact
customer service for reissue.
your assembly and reduce errors.
attention to waterproof and moisture-proof protection for the printer.
Do not touch any moving parts while the printer is running to avoid personal injury.
Do not touch the nozzle and hot bed when the printer is working, so as not to cause burns.
When using the touch screen in the printing process, please pay attention to the movement of the hot bed to prevent the hot bed
actual product.
Mizar S is not leveled at the factory. Please level the hot bed before using Mizar S, otherwise Mizar S will not be able to print.
Please refer to the relevant chapters of the manual to complete the leveling of the hot bed.
1
2
PACKING LIST
2
USB Cable*1 Power Cord*1&Shovel*1
Filament Holder*1 Tool Kit
User manual*1 Micro SD*1
Spare nozzle*2 Service Card*1 Screw bag
Hot Bed Kit*1 Gantry Kit*1 Y-axis Limit Switch*1
Belt Tensioner*2 Test Filament*1
Unpacking inspection After opening the Mizar S package, first check whether the accessories are missing, then check whether the hot end
and the hot bed are loose (the hot end and the hot bed may be loose during transportation), and finally check whether the power supply voltage
is correct. The specific methods are as follows:
3
Move the hot bed by hand to check whether it runs smoothly on the Y axis.
If it is found to be loose or stuck, please use the wrench in the tool kit to
adjust the 2 eccentric nuts under the hot bed. It is recommended to move
the hot bed while adjusting to prevent the hot bed from being too loose or
too tight on the Y axis.
2 Check the hot bed.
Move the hot end by hand to check whether it runs smoothly on the X
axis. If it is found to be loose or stuck, use the wrench in the tool kit to
adjust the eccentric nut behind the hot end. It is recommended to
move the hot end while adjusting to prevent the hot end from being too
loose or too tight on the X axis.
1 Check the hot end.
3
THE WHOLE MACHINE STRUCTURE INSPECTION
Pull the belt of the X&Y axis by hand to check whether the tightness is appropriate. If it is too loose or too tight, please use the belt tensioner on the X&Y side
to adjust(When Mizar S leaves the factory, the belt tensioners use ordinary screws. If necessary, you can replace them with the plastic handle screws in the
accessories that can be adjusted manually).
3 Check the X&Y axis belt.
9.4 MIZAR S power supply has two voltage ranges of 230V and 115V. Please select the voltage range according to the country or region where you are located
and ensure that the voltage range is in the correct position. Otherwise, the power supply will be damaged. Please make sure, then power on the printer.
4
CHECK POWER SUPPLY
4
115
5
MACHINE COMPONENTS
5
Filament Detector
Y-axis Limit Switch
115V/230V Power Supply
TF
Hotbed
Touch Screen
Hotend
X-axis Belt
Tensioner
Extruder
Y-axis belt Tensioner
USB
Filament Holder
Power
Switch
6
6
ASSEMBLE THE MACHINE
1 Find out the hot bed kit and gantry kit, placed them on a flat workbench. 3 Find the Y-axis limit switch kit and M3*16 screws, assemble the Y-axis
limit switch according to the picture below. Totally of 2 M3*16 screws
are needed.
4 Find the filament holder kit and assemble the filament holder.
2 Find the M5*35 screws in the tool kit, assemble the gantry kit and the hot
bed kit according to the picture below.Totally 4 M5*35 screws are required.
M5*35 M5*35
7
5 Find M3*6 screw and T-nut, fix the filament holder to the top of the gantry as
the picture below shown.
SCREWS M3*6
T-NUT
6 Insert the other end of the Teflon tube on the hot end into the extruder.
Table of contents
Other Geeetech 3D Printer manuals
Geeetech
Geeetech Acrylic I3 Pro User manual
Geeetech
Geeetech A30M User manual
Geeetech
Geeetech Acrylic I3 Pro Operation instructions
Geeetech
Geeetech Prusa I3 A pro User manual
Geeetech
Geeetech Rostock mini Manual
Geeetech
Geeetech Me Creator User manual
Geeetech
Geeetech Prusa I3 X User manual
Geeetech
Geeetech Acrylic I3 Pro User manual
Geeetech
Geeetech Acrylic I3 Pro Operation instructions
Geeetech
Geeetech Duplicator 5 User manual
Geeetech
Geeetech A10T User manual
Geeetech
Geeetech A30 User manual
Geeetech
Geeetech A20T User manual
Geeetech
Geeetech Acrylic I3 Pro Operation instructions
Geeetech
Geeetech A20 User manual
Geeetech
Geeetech A10 User manual
Geeetech
Geeetech A20M User manual
Geeetech
Geeetech A10M User manual
Geeetech
Geeetech Acrylic I3 Pro Operation instructions
Geeetech
Geeetech Prusa I3 A pro User manual
