Geeetech Delta Rostock mini G2 Instruction Manual
ShenZhenGETECHCO.
,
LTD
GEEETECH
Delta Rostock mini G2& G2s
Building instruction
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
GEEETECH
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenZhenGETECHCO.
,
LTD
Safety Instructions
Building the printer will require a certain amount of physical dexterity, common sense
and a thorough understanding of what you are doing. We have provided this detailed
instruction to help you assemble it easily.
However ultimately we cannot be responsible for your health and safety whilst
building or operating the printer, with that in mind be sure you are confident with
what you are doing prior to commencing with building or buying. Read the entire
manual to enable you to make an informed decision.
Building and operating involves electricity, so all necessary precautions should be
taken and adhered to, the printer runs on 12V supplied by a certified power supply, so
you shouldn’t ever have to get involved with anything over 12V but bear in mind
there can still be high currents involved and even at 12V they shouldn’t be taken
lightly.
High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end
can run about 230°C, the heated bed runs 110°C and the molten plastic extruded will
initially be at around 200°C, so special care and attention should be made when
handling these parts of the printer during operation.
We wouldn’t recommend leaving your printer running unattended, or at least until you
are confident to do so. We cannot be held responsible for any loss, damage, threat,
hurt or other negligent result from either building or using the printer.
GEEETECH
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenZhenGETECHCO.
,
LTD
Preparation
1. Unpack the kit and check if all parts are in the box and check the condition of each
part, there might be some damage during shipping. To help you with this, there is
BOM in the box and each bag was labeled with part number.
2. Contact our customer service immediately by email or through the website if you
find any missing or damaged parts. And on the bottom of the BOM, there is a
signature of reviewer, please take a picture of it and attach the picture in your mail.
3. Read through each chapter of these instructions to gain an over-all idea of what is
involved and how long it might take, before starting on the work described.
4. Before you start, you can put all the part in order to save your time especially those
screws and nuts. Do not mix them up.
5. Ensure you have the necessary skills to carry out the work, or enlist the help of
someone who does.
6. Work on a big firm table or bench in a clean dry well-lit area.
7. This kit contains tiny parts; please keep them away from kids under 3.
8. Ask for help if you run into any problems - our contact details are on the website
and we will always do our best to resolve any problems encountered.
ShenZhenGETECHCO.
,
LTD
GEEETECH
Chapter1 Base Assembly
1.1 Motor end assembly
Name
Part NO. qty Pic
Stepper motor
53
3
Pulley
33
3
Motor holder
A3
3
Motor holder
support
A4
6
Square nut
14
6
M3 X 12 Screw
18
12
M3 X 16 Screw
19
6
M3 washer
5
18
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenZhenGETECHCO.
,
LTD
GEEETECH
Step1. Mount the pulley on the motor shaft, one of the screws should be screwed on
the cross section of the shaft. Do not screw too tight to turn smoothly.
Step2. Assemble A3 and 2 A4 together, and screw up with M3 X 16 screw and M3
square nut.
Step3. Mount the motor on A3; screw it up with M3 X 12 screw.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenZhenGETECHCO.
,
LTD
GEEETECH
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenZhenGETECHCO.
,
LTD
GEEETECH
Repeat the steps for the other 2 motor ends
1.2 Connect motor ends to base plate
Name
Part NO. qty Pic
base plate
A2
1
Square nut
14
9
M3 X 16 Screw
19
9
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenZhenGETECHCO.
,
LTD
GEEETECH
M3 washer
5
9
Step1. Mount the 3 assembled motor ends on the base plate (A1); screw it up with
M3x16 screws and M3 square nuts.
Repeat the step for the other 2 motor ends
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenZhenGETECHCO.
,
LTD
GEEETECH
1.3 Mount the LCD panel
Name
Part NO. qty Pic
LCD frame
A8
1
LCD support
A9
2
LCD2004
54
1
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenZhenGETECHCO.
,
LTD
GEEETECH
Square nut
14
4
M3 X 16 Screw
19
4
M3 X 12 Screw
18
4
Spacer
34
4
M3 washer
5
8
Knob
55
1
Step1. Assemble the LCD frame and support plate together, screw up with M3 X 16
Screws and M3 square nuts.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
Other manuals for Delta Rostock mini G2
2
This manual suits for next models
1
Other Geeetech 3D Printer manuals
Geeetech
Geeetech A30T User manual
Geeetech
Geeetech Aluminum Prusa I3 User manual
Geeetech
Geeetech Acrylic I3 Pro User manual
Geeetech
Geeetech Acrylic Prusa I3 Pro C Operation instructions
Geeetech
Geeetech Me Creator User manual
Geeetech
Geeetech Acrylic I3 Pro Operation instructions
Geeetech
Geeetech Acrylic I3 Pro Operation instructions
Geeetech
Geeetech Aluminum Prusa I3 User manual
Geeetech
Geeetech GiantArm D200 User manual
Geeetech
Geeetech Acrylic I3 Pro User manual
Geeetech
Geeetech I3 Pro C User manual
Geeetech
Geeetech Prusa I3 X Instruction Manual
Geeetech
Geeetech Acrylic I3 Pro User manual
Geeetech
Geeetech Delta Rostock mini G2 Operator's manual
Geeetech
Geeetech Prusa M201 Operator's manual
Geeetech
Geeetech Duplicator 5 User manual
Geeetech
Geeetech Prusa I3 A pro User manual
Geeetech
Geeetech Acrylic I3 Pro User manual
Geeetech
Geeetech PrusaI3 X User manual
Geeetech
Geeetech Delta Rostock mini G2 pro Instruction Manual
