Gearlab GLB225001 User manual
GLB225001 User Manual
1
The terms HDMI and HDMI High Defini on Mul media Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
Administrator, Inc. in the United States and other countries.
3.Box Contents
Monitor x 1 Stand Stem x 1 Stand Base x 1
Screw x3 Screws x4
HDMI Cable x1
DP Cable x1 User Manual x 1
2
(for Stand Installaon) (for Wall Mounng)
Extra screws may be included as backup.
Power Cable x2 (UK+EU)
(AC 100-240V , 50/60Hz)
35mm
7mm
GLB225001 User Manual
4.Product Overview
4.1 –Monitor Bu ons
7 Power Connector
:Insert the power cable to supply power to the monitor.
8
9
HDMI Connectors : Insert one end of the HDMI cable into the computer’s HDMI
output and connect the other end to the monitor’s HDMI port.
1 M Menu Button: Press to display the OSD menu or enter sub-menus.
2 Down Button: Press to move down in the menus.
3 Up Button: Press to move up in the menus.
4 E Exit Button:Press to exit.
5 Power Button: Press to turn the monitor on/off.
6 LED Indicator: Changes colors to indicate status.
4.2 – Monitor Ports
3
10
Audio Output : Insert one end of the Audio cable into the computer’s Audio output
to receive the Audio signals from your monitor.
DP Connector : Insert one end of the DP cable into the computer’s DP output
and connect the other end to the monitor’s DP port.
7 8910
5.Stand Installa on
4
2. Take out the upper polyfoam and the inner package bag,lower polyfoam place on a
desktop or table,keep the lower foam underneath the monitor.
4.
5.
6.
3. See picture,fasten the stand stem and base with a screw.
Press the buon to remove the stand plate，Fix the stand plate into the stand stem
with the screw 5*11mm.
Fix the whole assembled stand into the monitor,and check carefully to make sure
it is fasten.
Hold on the stand stem and stand the monitor up on a flat,level desktop or table.
Note: Don't touch the screen during stand it up,to avoid screen broken.
Buon
Screw 5*11
Screw 5*11
stand plate
Quick click
Shaft assembly parts
6
7.Connec vity Op ons
7.1 – Connec ng Your Earphones
Plug in your earphones to receive audio signals from your monitor. If your earphones are
connected to the monitor and audio devices are connected to your computer at the same
me, the audio devices will not produce sound. Earphones and otheraudio devices not
included.
Listening to loud audio for prolonged perio me may permanently
damage your hearing.
7.2 – Connecting the Power Cable
Connect the included power cable to the power connector, and then plug the other
end into an wall outlet.
Earphones (Not included)
7.3 – DP Connec vity
In order for the monitor to receive DP signals from the computer, use the DP cable to
connect the monitor to the computer.
7.4– HDMI Connec vity
In order for the monitor to receive HDMI signals from the computer, use the HDMI cable
the monitor to the computer.
to connect
HDMI OUTPUT
PC
HDMI Cable (Included)
7
DP OUTPUT
DP Cable (Included)
8. Basic Opera
1. Insert one end of the DP cable into your PC’s graphics card. A HDMI cable may also
be used.
2.Connect the other end of the cable to the corresponding connector on your monitor.
3.Connect the power cable to your monitor then connect the other end to your power
source. It is recommended that you use a surge protector with adequate voltage if a wall
outlet cannot be reached directly .
4. Locate the power bu on on the monitor and press it to turn the monitor on.
9. Indicator Light
Solid blue light indicates power is on and the monitor is opera ng normally. Flashing blue light
indicates no video source , no horizontal or ver cal signal has been detected . Please ensure
your computer is on and all video cables are fully inserted and/or connected.
8
H
DP Connector
DMI Connector
10.OSD
9
The On-Screen Display (OSD) Menu may be used to adjust your monitor’s se ngs
and appears on screen a er turning on the monitor and pressing the Mb on.
When using the monitor for the firs me, se ngs will automa cally adjust to
omal se ngs according to your computer’s configura on and parts etc.
1.Press any one of the b ons ( M, , , E, ) to ac vate the naviga on window.
2. Press Mto enter the OSD menu.
3. Press or to browse func ons.
• Highlight the desired func on, then press Mto enter the sub-menu.
• Press or to browse sub-menus, then press Mto highlight the desired
func on.
• Press or to highlight an o on, then press Mto confirm the se ngs and exit
the current screen.
4. Press Eto exit the current screen.
3440*1440@60Hz
HDMI1
3440x1440@60Hz
Table of contents
