GE Monogram ZV370YSS User guide

For answers to your Monogram,®GE Profile

Performance Series,™GE Profile,™GE,

Hotpoint and RCA appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

Monogram.

™

Created 1/98

ZV370YSS—30" Professional Vent Hood

Dimensions and Specifications (in inches)

Accessories:

Before you Begin–Decorative duct covers are available

in 6" or 12" heights. the duct covers conceal the ductwork

running from the top of the hood to the ceiling or soffit.

Before you begin, you should determine the installation

height of the hood and order the correct size duct cover.

ZX6DC30YSS–6" high decorative duct cover

ZX12DC30YSS–12" high decorative duct cover

Dimensions and Clearances:

These vent hoods must be installed 30" min. and 36" max.

above the cooking surface. Installation will be easier if

the vent hood is installed before the range or cooktop

installation. These hoods can be installed into a soffit,

or when there is no soffit, they can be installed directly

onto a wall.

Note:

30” Hoods must use 7” round or 3-1/4”x12” duct.

18"

29-7/8"

25" 29-7/8"

12"

Optional 6" or 12"

Duct Cover

SOFFIT

SOFFIT INSTALLATION

30" MIN.

36" MAX."

WALL MOUNT INSTALLATION

Ceiling

30" MIN.

36" MAX."

For answers to your Monogram,®GE Profile

Performance Series,™GE Profile,™GE,

Hotpoint and RCA appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

Monogram.

™

Created 1/98

ZV370YSS—30" Professional Vent Hood

Dimensions and Specifications (in inches)

Soffit Framing:

We recommend that the vent hood and/or duct cover be

on site before final framing and wall finishing to more

accurately locate the ductwork and electrical service.

Note: If the top of the installation location does not meet

the soffit, use a 6" or 12" duct cover accessory

to conceal the duct run.

• The soffit should be constructed with 2 x 4s.

• Determine the installation location.

• Refer to “Soffit Installation” for mounting

screw locations.

• Mark the centerline of the installation.

• Add additional 2 x 4 studs at the locations illustrated.

• Allow 7" deep minimum opening below the soffit to

accommodate ductwork.

• Cut two wood shims, 2" x 10" x drywall thickness.

Secure to the bottom of the horizontal studs, flush with

the front, as illustrated. Note: If drywall is present, cut

away enough to expose studs.

Shims

Finished Drywall

Hood Width

10-11/16” 10-11/16”

7” Min.

For answers to your Monogram,®GE Profile

Performance Series,™GE Profile,™GE,

Hotpoint and RCA appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

Monogram.

™

Created 1/98

ZV370YSS—30" Professional Vent Hood

Dimensions and Specifications (in inches)

Wall Mount Framing:

Note: A decorative duct cover is available for wall mount

installations. The duct cover conceals the duct run from

the top of the hood to the ceiling. Choose the 6" or 12"

cover based upon installation height of the vent hood.

We recommend that the vent hood and decorative duct

cover be on site before final framing and wall finishing in

order to accurately locate the ductwork and electrical

service.

• Determine the location for installation.

• Mark the centerline of the installation.

Cut a sheet of plywood 30" wide and 18" high. If drywall

is installed, cut away enough to expose two vertical

studs, one on each side of the cutout. Secure the plywood

to the studs.

• Install additional aligning wall studs as illustrated.

No Additional

Wall Studs needed

Plywood Sheet

(Wall Hole Cut

Out x Drywall

Thickness)

Hood

Width

7" Min.

Additional

Wall Studs

Installed

Centerline of

Installation

Space

7" Min.

Hood

Width

8-15/16” 8-15/16”

6" or 12"

Duct

Cover

Ceiling Drywall

Rear View of Vent Hood

18" Hood Centerline 6-1/2"2-1/2"

6-1/2"

For answers to your Monogram,®GE Profile

Performance Series,™GE Profile,™GE,

Hotpoint and RCA appliance questions, call

GE Answer Center®service, 800.626.2000.

Listed by

Underwriters

Laboratories

Monogram.

™

Created 1/98

ZV370YSS—30" Professional Vent Hood

Dimensions and Specifications (in inches)

Soffit Installation:

• Drill 3/16" pilot holes through the shims and into the

soffit studs.

• Hold the hood against the soffit and secure with six lag

screws with washers.

• For additional support and to minimize vibration during

operation, we recommend that the hood be secured to

the back wall.

• Drive lag screws through the rear panel of the hood

and into the wall studs.

Wall Mount Installation:

• Drill 3/16" pilot holes, approximately 1-1/2" deep, in

all mounting screw locations.

• Hold the hood in position and drive lag screws in top

left and right mounting holes.

Note: 5/16" hanger bolts can be used in the two top

locations. Place the hood onto the hanger bolts and

secure with nuts and washers.

• Install lag screws with washers in remaining

mounting holes.

Installation Information:

Before installing, consult installation instructions

(Pub. No. 49-8816) packed with product for current

dimensional data.

SOFFIT INSTALLATION

WALL MOUNT INSTALLATION

Ceiling

5-1/2"

11-7/16" 12"

Junction

Box

30" Hood Top View - Front Side

29-7/8"

Back Side

11-7/16"

4-1/4"

3/4"

2-7/8"

3-1/8"

2-1/2"

12-7/16" 12-7/16"

8-15/16” 8-15/16”

6" or 12"

Duct

Cover

Ceiling Drywall

30" Hood Rear View

18" Mounting

Screw

Holes 6-1/2"

2-1/2"

6-1/2"

6” 6”

29-7/8”

Monogram.

™

Created 1/98

ZV370YSS—30" Professional Vent Hood

Monogram

Features and Benefits

•Straight Side Design

• 30” Width

• 600 CFM Vertical Exhaust

• Variable Speed Fan Control

• 1 Removable Stainless Steel Filter

• 2 Halogen Lamps

• 7” Round Duct

• Model ZV370YSS—Stainless Steel

Table of contents

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual

Nibe

Nibe S Series Installer manual