GE UCG1520NSS User manual
15” Built-In Compactors
UCG1500 Series
UCG1600 Series
Installation Instructions
If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737) or visit our website
at: GEAppliances.com. In Canada, please call 1.800.561.3344 or visit www.geappliances.ca
31-31581-1 09-19 GEA
READ CAREFULLY
KEEP THESE INSTRUCTIONS
FOR YOUR SAFETY
Read and observe all WARNINGS and CAUTIONS
shown throughout these instructions.
While performing installations described in
this booklet, gloves, safety glasses or goggles
should be worn.
IMPORTANT – Observe all governing codes and
ordinances.
• Note to Installer – Be sure to leave these
instructions for the consumer’s and local
inspector’s use.
• Note to Consumer – Keep these instructions
with your Owner’s Manual for future reference.
• Skill Level – Installation of this appliance
requires basic mechanical and electrical skills.
• Completion Time – 1 to 3 Hours. New
installations require more time than replacement
installations.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the GE Appliances Warranty. See
warranty information.
IMPORTANT
• This compactor is for household use only.
• Use this compactor only for its intended purpose.
• This compactor is designed for BUILT-IN
installations ONLY.
• Care should be exercised when the appliance is
installed or removed, to reduce the likelihood of
damage to the power supply cord.
• If you received a damaged compactor, you should
immediately contact your dealer or builder.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
For personal safety, remove house fuse or open
circuit breaker before beginning installation to avoid
severe or fatal shock injury.
WARNING
Do not allow items to fall or collect behind the
compactor. Failure to follow this instruction could
result in a fire.
WARNING
For your safety, the information in this manual must
be followed to minimize the risk of fire, explosion,
electric shock, and to prevent property damage,
personal injury, or death.
WARNING
2
Design Information
TOOLS
REQUIRED
• Level
• Phillips screwdriver
• Pliers
• Gloves
• Measuring tape
PRODUCT DIMENSIONS AND CLEARANCES
34” (86.4 cm)
to
35” (88.9 cm)
15”
(38.1
cm) min.
24”
(61 cm)
min.
Locate the outlet 18” (45.7 cm) min. from
the floor, 3” (7.6 cm) min. from either side
33-3/4”
(85.7 cm)
min.
to
35”
(88.9 cm)
max.
14-7/8” (37.8 cm)
23” (58.4 cm)
$OORZƎFP
clearance at the
front for a full drawer
opening.
$OORZƎFP
clearance on the right
side to the nearest
vertical wall or cabinet
for bag removal.
• Note: This compactor
is designed for built-in
applications only.
All parts are located in a package inside the drawer.
To order additional parts, call 800.626.2002 or visit
GEAppliances.com in the United States. In Canada,
call 1.800.561.3344 or visit www.GEAppliances.ca.
PARTS SUPPLIED
• 6 mounting screws,
#8 x 11/16” (1.8 cm)
long
• 2 side-mounting clips
• 2 countertop retaining
brackets
3
ADVANCE PLANNING
MODEL WITH A CUSTOM DRAWER
PANEL - UCG1650LII
The custom drawer panel and custom handle of
your choice should be secured to the compactor
before installation begins. A template with
instructions and installation hardware is provided
with this model.
For planning purposes, you may order the
template in advance by calling GE Appliances
at 1.800.GE.CARES (1.800.423.2737) or by
visiting our website at GEAppliances.com in the
United States. In Canada, call 1.800.561.3344
or visit GEAppliances.ca.
Order Pub. No. 31-31582. Complete panel
installation instructions are included on the
template.
CUSTOM PANEL SIZE REQUIREMENTS:
Maximum panel weight is 12 LBS (5.4 kg).
CLEARANCES
• You should be able to fully open the compactor
drawer. Six inches (15.2 cm) is required on the
right side of the compactor for bag removal.
• Allow 23 inches (58.4 cm) in front of the
compactor to remove the drawer.
• This compactor is designed as a built-in
appliance only. It may be located in any
convenient space under a countertop.
DO NOT OPERATE FREE-STANDING.
• The compactor may be installed beneath
countertops of stone or other materials that will
not accept screws. No trim kit is required.
The compactor must be securely installed in
a cabinet that is firmly attached to the house
structure. Weight on the compactor drawer
could cause the compactor to tip and result in
injury. Never allow anyone to climb, sit or hang
on the compactor drawer.
´Ǝ
(74.5 cm)
´Ǝ
(37.8 cm)
´Ǝ
(1.9 cm)
Thick
Custom
Panel
Installation Preparation
GROUNDING REQUIREMENTS
(CONT.)
Grounding Instructions:
For your personal safety, this appliance must be
grounded while in use to reduce the risk of electric
shock. The appliance is equipped with a three-
conductor power supply cord and a three-prong
grounding-type plug to fit the proper grounding-type
receptacle. The green (or green and yellow-colored)
conductor in the cord is the grounding wire. Never
connect the green (or green and yellow) wire to a
live terminal.
This appliance is for use on a nominal 120-volt
circuit and has a grounding attachment plug as
shown in the figure below. Make sure that the
appliance is connected to an outlet having the
same configuration as the plug. No adapter should
be used with this appliance.
To minimize possible shock hazard, the cord must
be plugged into the proper mating three-prong
grounding-type wall receptacle, grounded in
accordance with the National Electrical Code ANSI/
NFPA70—latest edition* and all local codes and
ordinances.
If a mating wall receptacle is not available, it is
the personal responsibility and obligation of the
customer to have a properly grounded three-prong
wall receptacle installed by a qualified electrician.
3-prong grounding-type wall receptacle
3-prong
grounding
plug
Grounding
plug
Power
supply
cord
Copies of the standards
listed may be obtained from:
* National Fire Protection
Association
Batterymarch Park,
Quincy, MA 02260
Grounded outlet
4
For personal safety, remove house fuse or open
circuit breaker before beginning installation to
avoid severe or fatal shock injury. Do not use an
extension cord or adapter plug with this appliance.
- Electrical Shock Hazard
WARNING
ELECTRICAL REQUIREMENTS
Be sure that the electrical connection and wire
size are adequate and in conformance with the
National Electric Code, ANSI/NFPA 70 - latest
edition, and all local codes and ordinances.
This appliance must have:
• 120V, 60Hz, AC-only, 15-ampere or
20-ampere, fused electrical supply.
• A properly grounded branch circuit.
• The outlet box should be located within reach
of the 36” (91.4) power cord.
• If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
It is recommended to have:
• A circuit breaker or time-delay fuse.
• A dedicated or individual branch circuit.
The improper connection of the equipment-
grounding conductor can result in a risk of electric
shock. Check with a qualified electrician or
service representative if you are in doubt that the
appliance is properly grounded.
• Electrical Ground is REQUIRED on this
compactor.
• DO NOT ground to a gas pipe.
• DO NOT change the power supply cord plug.
If it does not fit the outlet, have a proper outlet
installed by a qualified electrician.
• DO NOT have a fuse in the neutral or
grounding circuit. A fuse in the neutral or
grounding circuit could result in an electrical
shock.
• DO NOT use an extension cord with this
compactor.
Failure to follow these instructions could result in
death or serious injury.
WARNING
GROUNDING REQUIREMENTS
Installation Preparation
5
1 UNPACKING THE COMPACTOR
• Move the compactor close to the installation
location.
• Use a section of the shipping carton to protect
the finished floor.
• Remove all protective packaging materials such
as tape or shipping pads. Remove waxy residue
caused by shipping material with a mild solution
of liquid household cleaner and water.
• Check that the power supply cord is attached
to the cord clip on the rear of the compactor.
IMPORTANT: Use the shipping carton as a pad.
Do not slide the compactor across a finished
floor. Damage will occur.
Cord clip
• Open the compactor drawer and remove any
shipping materials or other items shipped in the
drawer.
• Do not remove the compactor bag (if installed).
• Grasp the sides of the drawer and lift it out of
the compactor. Place the drawer on a protected
surface. The drawer can scratch a finished floor.
2 LEVELING THE COMPACTOR
• The top of the compactor should be at least
ƎPPIURPWKHWRSRIWKHFDELQHWRSHQLQJ
You can adjust the height of the compactor by
turning the screws on the front leveling legs and
rear wheels.
• Place a level inside the compactor on the floor
of the cabinet.
• Use the leveling legs to adjust level front to back
and side to side.
Front leveling legs
Rear wheels
Loosen screw
on each side
Toekick
Adjustable Panel
6
Installation Preparation
3 ADJUST RETAINING BRACKET
• Determine installation depth of the compactor
beneath the countertop.
• Adjust the position of the retaining brackets so
that the screws can meet the underside of the
countertop.
• Mounting clips are provided for stone or other
hard countertops that will not accept screws.
Retaining
bracket
Countertop
4 ADJUSTING THE BASE TOEKICK
A toekick extension is supplied. It can be used to
cover any gaps from the bottom of the compactor
to the floor. (See the OPTIONAL STAINLESS
STEEL TOEKICK ASSEMBLY section following
this step for available accessories.)
• Remove the toekick screws as shown. Lift off
toekick piece.
• Loosen the adjustable panel screws, adjust to
touch the floor and tighten the screws.
NOTE: If replacing with stainless steel assembly
accessories, remove the screws and lift off.
Install the new stainless steel toekick assembly
accessories.
• Reinstall the toekick piece with the original
screws.
5 POSITION COMPACTOR UNDER
THE COUNTERTOP
• Plug the power cord into a properly grounded
receptacle.
• Carefully lift the front of the compactor slightly
and roll the unit into the cabinet opening.
Lift here
When moving the compactor, use gloves to
protect and cushion your hands.
To protect the finished flooring, use a dolly
to move the compactor near the installation
location.
Failure to follow these instructions could result in
injury.
CAUTION
OPTIONAL STAINLESS STEEL
TOEKICK ASSEMBLY
Order on-line at GEApplianceParts.com, 24 hours
a day or by phone at 877.959.8688 during normal
business hours. To replace the included black toekick
assembly with a stainless steel toekick assembly,
order the following three parts:
Part Number Accessory
WC17X10019 Kickplate - Stainless Steel
WC17X10011 Adjustable Panel
- Stainless Steel
WC17X10006 Toekick
- Stainless Steel
8VHWZR[ƎFPORQJPRXQWLQJ
screws to fasten each retaining bracket at the
top of the compactor to the underside of the
countertop.
• If the brackets cannot be attached to the
underside of the countertop, attach mounting
clips to the bracket. Fasten the compactor to
the cabinet front with mounting screws through
the mounting clips.
7
Installation
6 ATTACH THE COMPACTOR TO
THE COUNTERTOP
Mounting
screws
Retaining
bracket
Mounting
screw
Retaining
bracket
Mounting clip
• Grasp the sides of the drawer. Carefully slide
the drawer into the compactor.
7 REINSTALL THE COMPACTOR
DRAWER
• Set the bag caddy into the drawer and hook the
prepunched holes in the caddy on the bag
retainer buttons.
• Set the trash bag into the bag caddy and fold
over.
• Hook the holes in the bag over the bag retainer
buttons.
8 INSTALLATION OF THE TRASH
BAG CADDY (on some models)
Bag retainer
buttons
Trash
bag
caddy
• Turn power on at the source.
• Turn the knob to ON.
• Make sure the drawer is fully closed.
• Lift the foot pedal to start the cycle.
• The ram will travel downward, reverse and
return to the starting position.
• The compactor will shut off automatically.
• The cycle should take less than 30 seconds.
• Refer to your Owner’s Manual for operating
instructions.
9 FINALIZE THE INSTALLATION
NOTE: Product improvement is a continuing endeavor at GE Appliances.
Therefore, materials, appearance and specifications are subject to
change without notice.
Printed in China
Compacteur intégré de 38 cm (15 po)
UCG1500 Série
UCG1600 Série
31-31581-1 09-19 GEA
Directives d’installation
Pour toute question, composez le 1.800.561.3344 ou visitez notre site web: www.electromenagersge.ca
AVANT DE COMMENCER : Veuillez lire
attentivement toutes les directives qui suivent. POUR VOTRE SÉCURITÉ
Veuillez lire et observer toutes les mises en
garde (AVERTISSEMENT et ATTENTION) données
dans les présentes directives.
Pour effectuer l’installation décrite dans les
présentes directives, il faut porter des gants et
des lunettes de sécurité.
IMPORTANT – Observez tous les codes et
ordonnances en vigueur.
• Note à l’installateur – Veuillez laisser les
présentes directives au consommateur pour
l’inspecteur local.
• Note au consommateur – Veuillez conserver
les présentes directives avec votre Manuel
d’utilisation pour consultation ultérieure.
• Compétences requises – L’installation de cet
appareil exige des compétences de base en
mécanique et en électricité.
• Durée de l’installation – Entre 1 et 3 heures.
L’installation d’un nouveau lave-vaisselle exige
plus de temps que le remplacement d’un ancien
modèle.
• L’installateur est responsable de la qualité de
l’installation.
• Toute défaillance du produit attribuable à une
installation inadéquate n’est pas couverte par la
garantie de GE Appliances. Reportez-vous à la
garantie du produit.
IMPORTANT
• Ce compacteur ne doit être utilisé qu’à des fins
domestiques seulement.
• Utilisez ce compacteur seulement aux fins prévues.
• Ce compacteur est conçu SEULEMENT pour des
installations ENCASTRÉES.
• Il importe d'user de prudence lorsque l'appareil
est installé ou déplacé afin de prévenir
l'endommagement du cordon d'alimentation.
• Si le compacteur que vous avez reçu est
endommagé, communiquez immédiatement avec
votre détaillant ou l’entrepreneur en construction.
VEUILLEZ LIRE ATTENTIVEMENT
CONSERVER CES DIRECTIVES
Pour votre sécurité, retirez le fusible de la maison
ou ouvrez le disjoncteur avant l’installation, pour
éviter des blessures graves ou même le décès
pouvant être causé par un choc électrique.
AVERTISSEMENT
Ne laissez pas d’objets tomber ou s’accumuler
derrière le compacteur. Le non-respect de ces
instructions pourrait provoquer un incendie.
AVERTISSEMENT
Pour votre sécurité, veuillez suivre les directives
données dans le présent manuel afin de réduire
au minimum les risques d’incendie, d’explosion et
de chocs électriques et prévenir tout dommage et
blessure grave ou mortelle.
AVERTISSEMENT
Conception
2
DIMENSIONS ET DÉGAGEMENTS DU PRODUIT
• Niveau
• Tournevis à tête
Phillips
• Pinces
• Gants
• Ruban à mesurer
OUTILS NÉCESSAIRES
86,4 à 88,9 cm
(34 à 35 po)
38,1 cm
(15 po)
min.
61 cm
(24 po)
min.
Placez la prise à 45,7 cm (18 po) ou plus du sol
et à 7,6 cm (3 po) ou plus d’un côté ou de l’autre.
85,7 cm
(33 3/4 po)
min.
à 88,9 cm
(35 po)
max.
37,8 cm (14 7/8 po)
58,4 cm
(23 po)
• Prévoyez un dégagement
de 58,4 cm (23 po) à
l’avant pour l’ouverture
complète du tiroir.
• Prévoyez un dégagement
de 15,2 cm (6 po) du côté
droit jusqu’au mur vertical
ou à l’armoire la plus
proche pour retirer le sac.
• Remarque : ce
compacteur est conçu
pour une installation
encastrée.
Toutes les pièces se trouvent dans un emballage
à l’intérieur du tiroir. Pour commander des pièces
supplémentaires, composez le 800.626.2002
ou visitez GEAppliances.com aux États-Unis.
Au Canada, composez le 1.800.561.3344 ou
visitez www.GEAppliances.ca.
PIÈCES
FOURNIES
• 6 vis de montage n° 8
x 11/16 po (1,8 cm) de
long
• 2 agrafes de montage
de côté
• 2 fixations de retenue
pour le comptoir
This manual suits for next models
5
Table of contents
Languages:
Other GE Trash Compactor manuals
Popular Trash Compactor manuals by other brands
Whirlpool
Whirlpool GX900QPLQ - 15" Trash Compactor Use and care guide
Vestil
Vestil FM-T-DUMP instruction manual
Euro Shatal
Euro Shatal RP4014-50 operating instructions
third coast equipment
third coast equipment SP3410 Operator's manual
Cucine Oggi
Cucine Oggi EKKO CUBE 40 9000 Assembly instructions
Viking
Viking Designer Series installation guide
