GE Mentor EM User manual
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
04/03/2014
User's Manual Mentor EM Portable Equipment
Mentor EM
Portable Equipment
User’s Manual
103M0987 Rev. C
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
ii 04/03/2014
Mentor EM Portable Equipment User's Manual
Documentation no.: A586590/EB.0908
Published by GE Sensing & Inspection Technologies
Date: 04/03/2014 File: MentorEMUser_040314.indd
Printed in 2014
In order to further develop our products, we reserve the right to change data and designs without prior notice. All
rights reserved, particularly rights relating to duplication,
Dissemination and translation excepted. No part of this publication may be reproduced, processed or disseminated
in any form (e.g. through photocopying, microlming, electronic data processing and/or storage or other means)
without the prior written consent of GE Sensing & Inspection Technologies.
Website: http://www.geittechsupport.com
Phone: See listing of Global Tech Support at the end of this manual.
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
iii
04/03/2014
User's Manual Mentor EM Portable Equipment
Table of Contents
Chapter 1: Introduction.................................................................................................................................................................................................................................... 1-1
Important Notice ................................................................................................................................................................................................................................... 1-2
Limited Service Warranty .................................................................................................................................................................................................................... 1-5
Safety Information ................................................................................................................................................................................................................................ 1-6
Compliance Information .................................................................................................................................................................................................................... 1-14
Chapter 2: Features........................................................................................................................................................................................................................................... 2-1
Mentor EM Instrument Overview ....................................................................................................................................................................................................... 2-2
Using this Manual.................................................................................................................................................................................................................................. 2-2
Powering On and Connecting to the Instrument ............................................................................................................................................................................ 2-3
Desktop Features .................................................................................................................................................................................................................................. 2-4
Chapter 3: Operation ........................................................................................................................................................................................................................................ 3-1
LaunchingWorkows ........................................................................................................................................................................................................................... 3-2
InstallingNewWorkows .................................................................................................................................................................................................................... 3-2
NavigatingwithinaWorkow............................................................................................................................................................................................................ 3-3
WorkowFeatures ................................................................................................................................................................................................................................ 3-4
EM Setup Menu and Changing Parameter Values .......................................................................................................................................................................... 3-5
Data Display Screens ............................................................................................................................................................................................................................ 3-6
Working with Gates............................................................................................................................................................................................................................... 3-7
Interpreting the LED Indicator Light ................................................................................................................................................................................................. 3-8
Using the Data Review Tool ............................................................................................................................................................................................................... 3-9
Changing the System Settings ......................................................................................................................................................................................................... 3-10
Working with Stored Files .................................................................................................................................................................................................................. 3-11
WiConnections.................................................................................................................................................................................................................................. 3-13
Bluetooth Connections ....................................................................................................................................................................................................................... 3-14
Using the Mentor EM Software.......................................................................................................................................................................................................... 3-15
AppendixA–EMParameterListingwithDenitions............................................................................................................................................................................ AP A-1
AppendixB–Specications....................................................................................................................................................................................................................... AP B-1
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
iv
04/03/2014
Mentor EM Portable Equipment User's Manual
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
1-1
04/03/2014
User's Manual Mentor EM Portable Equipment
Chapter 1:
Introduction
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
1-2 04/03/2014
Mentor EM Portable Equipment User's Manual
Important Notice
The following information must be read and understood by any user of GE
Inspection Technologies equipment. Failure to follow these instructions can lead
to errors in measurements or other test results. Decisions based on erroneous
results can, in turn, lead to property damage, personal injury or death. Any use
for medical applications or other purposes is not allowed.
General Warnings
Proper use of test equipment requires three essential elements:
• Selection of the correct test equipment.
• Knowledge of the specic “test application requirements.”
• Operator training.
The operating manual provides instruction in the basic set up and operation of
the testing equipment.
Operator Training
Operators must receive adequate training before using test equipment.
Operators must be trained in general testing procedures and in the set up and
performance required by a particular test.
More specic information about operator training, qualication, certication,
and test specications is available from various technical societies, industry
groups, and government agencies.
Safety Information
ATTENTION! This is an instrument for materials testing. Any use for medical
applications or other purposes is not allowed.
The instrument may only be used in industrial environments.
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
1-3
04/03/2014
User's Manual Mentor EM Portable Equipment
Software
According to the current state of the art, software is never completely free from
errors.
Before using any software-controlled test equipment, please make sure that the
required functions operate perfectly in the intended combination.
Defects/Errors and Exceptional Stresses
If you have reason to believe that a safe operation of your instrument is no
longer possible, you have to disconnect the instrument from its AC Power
Adapter/Battery Charger, shut it down, and secure it against unintentional
reconnection.
A safe operation is no longer possible if:
• The instrument shows visible damages.
• The instrument no longer operates perfectly.
• Being subjected to heavy stresses during transportation
• After prolonged storage under adverse conditions like exceptional
temperatures and/or especially high air humidity, or corrosive environmental
conditions.
Service
Every effort has been made to provide you with a reliable product. However,
should service become necessary, GE Inspection Technologies has established
a number of Factory Trained Service Centers. For the location of the nearest
facility, refer to the end of this user manual.
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
1-4 04/03/2014
Mentor EM Portable Equipment User's Manual
Batteries
Only batteries (Lithium-ion) recommended and supplied by GE Inspection
Technologies may be used for instrument operation.
NOTE:
Internal batteries may only be replaced by a factory trained service center.
Opening the instrument case in an attempt to access the batteries will void the
instrument’s warranty. An externally connected battery pack is available from
suppliers as described in this manual.
NOTE:
When the instrument reaches the end of its life, the Lithium-ion battery must
be removed. Then properly dispose of the instrument and of the Lithium-ion
battery.
Power plug
Class 1: For AC line powered equipment the power plug may only be inserted
into a grounding-type receptacle. Any disconnection or interruption of the
protective conductor may make the instrument unsafe. When connecting
equipment with other devices, the protective conductors shall be made
equipotential.
Class 2: Use only the power cord and AC Power Adapter/Battery Charger
supplied by GE Inspection Technologies for this instrument. Serious harm to the
instrument is highly likely if the incorrect power supply is used.
ChargerSpecications
AC input to charger specication: 100–240 VAC, 47–63 Hz
DC charge input specication: 12 VDC ± 5%, 72 W
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
1-5
04/03/2014
User's Manual Mentor EM Portable Equipment
Limited Service Warranty
If, through our negligence, GE Inspection Technologies directly caused damage
to your equipment while the equipment is in the sole custody and control of
GE Inspection Technologies, we shall choose at our opinion either to repair
the damage or replace the damaged portion of the equipment at our own
expense, or to indemnify and hold you harmless for such physical damage to
the Equipment. The equipment shall be free of any claim of ownership by third
parties and when new, be free from defects in material and workmanship and
perform in accordance with the Product’s specications under normal use and
service.
EXCEPT FOR THE WARRANTY SET IN THIS PARAGRAPH, GE INSPECTION
TECHNOLOGIES EXPRESSLY DISCLAIMS ALL WARRANTIES AND REPRESENTAION
OF ANY KIND WITH RESPECT TO OUR SERVICES OR THE INFORMATION
CONTAINED IN ANY REPORTS THAT WE ISSUE TO YOU, WHETHER EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, TITLE AND WARRANTIES
ARISING FROM COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE
USAGE.
This limited warranty shall not apply to any problems arising from (i) failure to
follow the product instructions or failure to perform preventive maintenance,
(ii) service, repair or modication by someone other than GE Inspection
Technologies or one of our authorized service representatives; or (iii) external
causes, such as accident, abuse, misuse, or problems with electrical power.
The use of unauthorized spare parts shall render the manufacturer’s warranty
null and void.
Copyright by GE Sensing & Inspection Technologies 50 Industrial Park Road Lewistown, PA 17044
1-6
04/03/2014
Mentor EM Portable Equipment User's Manual
Safety Information
Follow the safety instructions and exercise caution at all times to reduce the risk
of accidents, personal injury, and material damage.
NOTE:
This message indicates additional information.
DANGER!
Immediate danger: situation will cause death or serious injury if not averted.
WARNING!
This term indicates danger and the possibility of personal injury.
CAUTION
This term indicates that damage could occur to equipment.
WARNING!
Danger resulting from misuse!
Table of contents
Other GE Test Equipment manuals
GE
GE EVT-Pro 2.0 User manual
GE
GE Druck DPI612 User manual
GE
GE Druck DPI 610 User manual
GE
GE MicroVersaTrip TVTS1 User manual
GE
GE EntelliGuard G User manual
GE
GE Druck DPI611 User manual
GE
GE ADTS552F User manual
GE
GE ADTS 405F Mk2 Setup guide
GE
GE Druck ADTS 2 Series Use and care manual
GE
GE EntelliGuard User manual
