GE "ExecutiveSeries"USB2.0 HO97863 User manual

HO97863

“Executive Series” USB 2.0

7-Port Hub

INSTRUCTION MANUAL

www.jascoproducts.com

I. INTRODUCTION...................................3

II. OVERVIEW...........................................4

III. SAFETY INSTRUCTIONS ....................5

IV. POWER MODE SETTING ....................6

V. MOUNTING YOUR HUB.......................7

VI. HARDWARE INSTALLATION ........... 8-9

VII. SOFTWARE INSTALLATION..............10

VIII. TROUBLESHOOTING ........................11

IX. TECHNICAL SPECIFICATIONS .........12

X. FCC COMPLIANCE STATEMENT......13

XI. LIMITED LIFETIME WARRANTY .......14

Table of Contents

Congratulations on the purchase of your GE

‘Executive Series’ USB 2.0 7-port Hub! This

GE “Executive Series” Hub will allow you to

receive the maximum possible bandwidth for

all of your USB 2.0 and 1.1 devices!

Please read this entire manual carefully before

using your “Executive Series” Hub. Follow

the instructions to prevent damage to the

“Executive Series” Hub and/or the connecting

devices.

THIS PACKAGE INCLUDES:

• USB 2.0 7-Port Hub

• AC Power Adapter

• USB 2.0 Extension Cable (6 feet)

• Aluminum mounting bracket/stand and

spacer card

• User’s Manual

• Mounting screws

I. Introduction

II. Overview

GE Hub technology gives you the best of USB

1.1 and 2.0 in one Hi-Speed USB 2.0 Hub.

Connect USB 2.0 devices for data transfer

rates of up to 480 Mbps. At the same time

connect USB 1.1 devices for a guaranteed

12 Mbps of bandwidth per device. Use any

combination of USB 1.1 and 2.0 devices

– this GE USB Hub will adapt to give you the

greatest bandwidth possible for each device!

FEATURES

• USB 1.1 and 2.0 compatible

• Full speed guaranteed for each USB 1.1 device

• AC adapter supports all high power USB de-

vices

• LED to indicate power

• Mountable with the included bracket/base

• Plug and Play

• Bus fault detection and recovery

• Per port over-current detection and protection

• All downstream ports support high-speed (480

Mbps), full-speed (12 Mbps) and low-speed (1.5

Mbps) operations.

III. Safety Instructions

Always read the Safety Instructions carefully.

➢Keep this user’s manual for future

reference.

➢Keep this equipment away from humidity.

➢Do not expose to moisture.

➢Replace if dropped and damaged.

➢Replace if you see obvious signs of

breakage.

➢If you cannot get it to work according

to this User’s Manual refer to the

Troubleshooting section of this manual

(VIII) or contact technical support at

www.jascoproducts.com.

IV. Power Mode Setting

There are two power mode options for the GE

“Executive Series” USB 2.0 7-Port Hub.

The rst is self-power mode (recommended),

which requires the use of the AC power

adapter. In this mode, each port is provided

with 500 milliamps, allowing for additional

hubs, cameras and other high-powered

devices.

The second is bus-power mode, which does

NOT require the use of the AC power adapter.

In this mode, the hub is provided with 500

milliamps for all 7 ports. This should be

adequate for mice, keyboards, and other low

power devices. If you are not sure or if device

performance is poor, use the AC adapter.

When using the AC power adapter, make

sure the plug is properly connected to the hub

and to a standard electrical outlet. GE Surge

protection is recommended.

An aluminum mounting bracket/base is

provided for mounting your hub. To begin,

choose where you would like the hub located.

V. Mounting Your Hub

Mount the bracket/base using the supplied

screws, slide the spacer insert into the

bracket/base and then slide on the hub for a

snug  t.

Make sure your computer has all the neces-

sary updates required to support USB. These

can be found on Microsoft’s website.

1. (Optional) Position the Hub as desired

using the directions in Section V.

2. (Optional) Plug the included AC power

adapter into the Power Jack on the side

of the USB 2.0 7-Port Hub. Note: Refer to

Section IV for more details on AC power

adapter use.

VI. Hardware Installation

3. (Optional) Plug the AC power adapter

into a standard electrical outlet or GE

Surge Protector (recommended). The

power LED should illuminate. Note: Refer

to Section IV for more details.

4. Plug the A-type connector of the USB 2.0

device cable into the USB port of your

computer. Plug the mini (B) type connec-

tor of the USB cable into the hub.

5. Connect your USB devices to any of the

7 available downstream Ports.

Note: If you connect the hub to a USB 1.1

Port, your computer may warn you that a

high-speed device has been connected

to a non-high speed port. Your hub will

function properly, however it will function

at the USB 1.1 speed of your USB port.

Software installation is only required for

Windows®98 and 98 SE users. Users of all

other Operating Systems, including Windows®

NT, ME, 2000, VISTA, XP and any Mac®OS,

may skip this section.

1) Connect the hub to your computer.

2) Windows®98 and 98 SE will detect the

hub and automatically run the “Add New

Hardware Wizard”.

3) When the initial screen appears introducing

the “Add New Hardware Wizard”, click

Next.

4) Select “Search for the best driver for your

device (Recommended): and click Next.

5) When asked to select a location to search

for the drivers, use the default selection. Do

not change the location. Click Next.

6) Click Next to accept the location the driver

will be installed in.

7) On the nal screen notifying you that the

driver has been installed, click Finish.

VII. Software Installation

This manual suits for next models

Table of contents

Languages:

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual