GE "Executive Series" USB 2.0 HO97864 User manual
HO97864
“Executive Series” USB 2.0
4-Port Hub
INSTRUCTION MANUAL
www.jascoproducts.com
2
I. INTRODUCTION...................................3
II. OVERVIEW...........................................4
III. SAFETY INSTRUCTIONS ....................5
IV. POWER MODE SETTING ....................6
V. MOUNTING YOUR HUB.......................7
VI. HARDWARE INSTALLATION ...............8
VII. SOFTWARE INSTALLATION..............10
VIII. TROUBLESHOOTING ........................11
IX. TECHNICAL SPECIFICATIONS .........12
X. FCC COMPLIANCE STATEMENT......13
XI. LIMITED LIFETIME WARRANTY .......14
Table of Contents
3
Congratulations on the purchase of your GE
‘Executive Series’ USB 2.0 4-port Hub! This
GE “Executive Series” Hub will allow you to
receive the maximum possible bandwidth for
all of your USB 2.0 and 1.1 devices!
Please read this entire manual carefully before
using your “Executive Series” Hub. Follow
the instructions to prevent damage to the
“Executive Series” Hub and/or the connecting
devices.
THIS PACKAGE INCLUDES:
• USB 2.0 4-Port Hub
• AC Power Adapter
• USB 2.0 Extension Cable (6 feet)
• Aluminum mounting bracket/stand and
spacer card
• User’s Manual
• Mounting Screws
I. Introduction
4
II. Overview
GE Hub technology gives you the best of USB 1.1
and 2.0 in one Hi-Speed USB 2.0 Hub. Connect
USB 2.0 devices for data transfer rates of up to 480
Mbps. At the same time connect USB 1.1 devices
for a guaranteed 12 Mbps of bandwidth per device.
Use any combination of USB 1.1 and 2.0 devices
– this GE USB Hub will adapt to give you the
greatest bandwidth possible for each device!
FEATURES
• USB 1.1 and 2.0 compatible
• Full speed guaranteed for each USB 1.1
device
• AC adapter supports all high power USB
devices
• LED to indicate power
• Mountable with the included bracket
• Plug and Play
• Bus fault detection and recovery
• Per port over-current detection and protection
• All downstream ports support high-speed (480
Mbps), full-speed (12 Mbps) and low-speed
(1.5 Mbps) operations.
5
III. Safety Instructions
Always read the Safety Instructions carefully.
➢Keep this user’s manual for future
reference.
➢Keep this equipment away from humidity.
➢Do not expose to moisture.
➢Replace if dropped and damaged.
➢Replace if you see obvious signs of
breakage.
➢If you cannot get it to work according
to this User’s Manual refer to the
Troubleshooting section of this manual
(VIII) or contact technical support at
www.jascoproducts.com
6
IV. Power Mode Setting
There are two power mode options for the GE
“Executive Series” USB 2.0 4-Port Hub.
The rst is self-power mode (recommended),
which requires the use of the AC power
adapter. In this mode, each port is provided
with 500 milliamps, allowing for additional
hubs, cameras and other high-powered
devices.
The second is bus-power mode, which does
NOT require the use of the AC power adapter.
In this mode, the hub is provided with 500
milliamps for all 4 ports. This should be
adequate for mice, keyboards, and other low
power devices. If you are not sure or if device
performance is poor, use the AC adapter.
When using the AC power adapter, make
sure the plug is properly connected to the hub
and to a standard electrical outlet. GE Surge
protection is recommended.
7
Mount the bracket/base using the supplied
screws, slide the spacer insert into the bracket/
base and then slide on the hub for a snug t.
V. Mounting Your Hub
An aluminum mounting bracket/base is
provided for mounting your hub. To begin,
choose where you would like the hub located
8
VI. Hardware Installation
Make sure your computer has all the neces-
sary updates required to support USB. These
can be found on Microsoft’s website.
1. (Optional) Position the Hub as desired
using the directions in Section V.
2. (Optional) Plug the included AC power
adapter into the Power Jack on the side of the
USB 2.0 4-Port Hub. Note: Refer to Section IV
for more details on AC power adapter use.
9
3. (Optional) Plug the AC power adapter
into a standard electrical outlet or GE Surge
Protector (recommended). The power LED
should illuminate. Note: Refer to Section IV for
more details.
4. Plug the A-type connector of the USB 2.0
device cable into the USB port of your com-
puter. Plug the mini (B) type connector of the
USB cable into the hub.
5. Connect your USB devices to any of the
4 available downstream Ports.
Note: If you connect the hub to a USB 1.1 Port,
your computer may warn you that a high-speed
device has been connected to a non-high speed
port. Your hub will function properly, however it will
function at the USB 1.1 speed of your USB port.
10
Software installation is only required for
Windows®98 and 98 SE users. Users of all
other Operating Systems, including Windows®
NT, ME, 2000, VISTA, XP and any Mac®OS,
may skip this section.
1) Connect the hub to your computer.
2) Windows®98 and 98 SE will detect the hub
and automatically run the “Add New Hardware
Wizard”.
3) When the initial screen appears introducing
the “Add New Hardware Wizard”, click Next.
4) Select “Search for the best driver for your
device (Recommended): and click Next.
5) When asked to select a location to search for
the drivers, use the default selection. Do not
change the location. Click Next.
6) Click Next to accept the location the driver will
be installed in.
7) On the nal screen notifying you that the
driver has been installed, click Finish.
VII. Software Installation
This manual suits for next models
1
Table of contents
Languages:
Other GE Switch manuals
GE
GE RAK204 User manual
GE
GE USB 2.0 7-Port Hub HO97916 User manual
GE
GE MULTILINK ML2400 User manual
GE
GE GuardSwitch 300 Series User manual
GE
GE 45609 User manual
GE
GE EntelliGuard G Technical Document
GE
GE 15250 User manual
GE
GE ZW4106 User manual
GE
GE AV-Line Instruction Manual
GE
GE CWLSWDMBWF1 User manual
GE
GE CWLSWDMBWF1 User manual
GE
GE 70R-1000D User manual
GE
GE SecoGear User manual
GE
GE NETernity CP921RC-30X Quick user guide
GE
GE GBX24 Quick user guide
GE
GE GuardSwitch 300 Series User manual
GE
GE DS-242-POE Assembly instructions
GE
GE Cync CSWONBLBWF1NN User manual
GE
GE MultiLink User manual
GE
GE Zenith ZTS Series User manual
