GE VAT2000 Series User manual



GE Power Controls

PCST-3299E-R0

VAT2000 AC Drive Series

U2KV23DN1

Speed Detection Feedback

INSTRUCTION MANUAL

NOTICE

1. Read both this manual and VAT2000 Instruction Manual (ST-

3251) before using the U2KV23DN1, and store in a safe place for

reference.

2. Observe the warnings, cautions and other matters described in

this manual.

3. Make sure that this manual is delivered to the final user.

4. The content of this manual can be changed without notice

GE Power Controls

U2KV23DN1 Instruction Manual

- -1

1. Specifications

This manual is for Speed detecting option PCB U2KV23DN1.( Card NPQF-DN09). The option allows

the use of a standard complimentary encoder for speed detection feedback.

Encoder specifications:

Item Specifications

Supply voltage 12VDC±1.2V

Output method Complimentary

Output pulse voltage VH(High revel pulse voltage):above 8.0V , VL(Low revel pulse

voltage):below 1.0V at the terminal on V23-DN1.

Supplied current 150mA (Including signal currents) (Refer Note2 on page 2)

Rising/falling time Within 1µs

Output signal 90º±30º phase difference signal(A phase pulse, B phase pulse)

(Refer Note3 on page 2)

Output pulse

frequency The output pulse frequency is required within 60±10kHz when the

motor rotates at the max. speed.

2. Installation

a) Confirm that the Jumper W1 on U2KV23DN1 is set to 1(2PP) side.

b) Remove the front cover of VAT2000S

CAUTION

There is a risk of electric shocks.

The VAT2000S has a built-in electrolytic capacitor, so a charge will remain even when the inverter power is turned OFF. Always

observe the following times before carrying out wiring work.

• Wait at least 20 minutes after turning the power OFF before starting work. Make sure that thedisplays on the operation panel

have gone out before removing the cover.

• After removing the cover, confirm that the "CHARGE" LED in the VAT2000S does not light. Also check that the voltage

between terminals L+1 or L+2 and L– is 15V or less before starting the inspections. (Check with the "CHARGE" LED if the

unit is not provided with the L– terminal.)

c) Install U2KV23DN1 to the position Option I on the Control PCB cover and make sure not to bend the

pins of reverse of U2KV23DN1.

U2KV23DN1 Instruction Manual

- -2

3. Wiring

An example of the encoder connection is given below.

Note 1: The option U2KV23DN1 is card number NPQF-DN09.

Note 2: If the current to encoder exceeds 150mA, use an external power supply. In this case, connect

the external power source only to the encoder. DO NOT connect the power source to TB1-

1,2[12KP] or -3[0KP] on U2KV23DN1.

Note 3: Below drawing shows A, B encoder phases when motor rotates forward.

A phase

pulse

B phase

pulse

90º 90º 90º 90º

12V

2.2KΩ

1KΩ

470

TB1

-1,2[12KP]

-3[0KP]

-7[PA]

-8[0KP]

-9[PB]

-10[0KP]

DC12V Max.150mA

(Refer Note2 on page 2)

[A phase pulse output]

[B phase pulse output]

[common]

-11[PAOUT]

-13[PBOUT]

-12,-14[0KP]

A phase

pulse

B phase

pulse

Set W1 to 1(2PP)side.

2PP

Suitable cable for encoder

0.75mm2(50m or less), 6-core twisted shield strands

U2KV23DN1(NPQFDN09)

1PP

Encoder

3.3KΩ

12V

ENCODER

DC12V Max.150mA

TB1

-1,2[12KP]

-3[0KP]

U2KV23DN1

12V

Power

source

Other manuals for VAT2000 Series

Table of contents

Other GE Security Sensor manuals

GE 45132 User manual

GE TX-5011-03-1 User manual

GE GS930 User manual

GE KM170 User manual

GE INDOOR/OUTDOOR PIR MOTION SENSORS... User manual

GE 50487 - Ultrasonic Sensor Parking Alert User manual

GE Interlogix ARITECH 1500 Series Product manual

GE PI6000 - Sentrol Motion Detector User manual

GE PrecisionLine RCR-90 User manual

GE DD205RF/60-947-8A Series User manual

GE 60-639-95R User manual

GE VE1016 Series Assembly instructions

GE DDI602 Assembly instructions

GE ARITECH 1500 Series Product manual

GE Motion Sensor User manual

GE RCR 50 - Security PrecisionLine Dual Technology Motion... User manual

GE 250-CO Assembly instructions

GE KL700 Series Manual

GE Interlogix AP100PI User manual

GE VersaSafe VersaPoint Series User manual

GE EV1000PI Series User manual

GE DD205-AD Series User manual

GE VE1100 Series Assembly instructions

GE AP950PI - Security High-Security PIR Motion... User manual

Popular Security Sensor manuals by other brands

THORLABS

THORLABS PDA10JT user guide

Waeco

Waeco UV-DETECT operating manual

Intermatic

Intermatic IOS-DSIMF manual

urmet domus

urmet domus 1083 manual

Siemens

Siemens AZL66 Series manual

BTI

BTI Profiline Multi Finder operating instructions

Challenger

Challenger SL01 instruction manual

DMP Electronics

DMP Electronics 1122INT installation guide

Rielta

Rielta Ladoga MK-RK installation guide

Mirion Technologies

Mirion Technologies ACCURAD PRD user manual

Bosch

Bosch DS835 installation instructions

DBI SALA

DBI SALA EZ Stop User instruction manual

Lamptime

Lamptime ST05C instructions

Ubiquiti

Ubiquiti MFI-MSC quick start guide

Subsite

Subsite 910R Support

Satel

Satel OPAL Pro manual

Aleph

Aleph XC-1XTEU manual

Pima

Pima LARIS QUAD installation instructions