14 15
1312
TRANSMISSION COLLISION
Signals from other household devices, such as door bells,
home security systems and entry controls, may interfere with
those of this product and cause temporarily reception failure.
This is normal and does not affect the general performance of
the product. The transmission and reception of temperature
readings will resume once the interference recedes.
HOW TO CHANGE THE
TEMPERATURE ALARM SETTING
1. Press once [TEMP ALARM] button,
2. Then Press and hold [TEMP ALARM] button for
2 seconds.
3. Enter the Hi [ ] or Lo [ ] temperature alert setting
value by using [ ] or [ ] button.
4.Press [TEMP ALARM] once to exit.
HOW TO SET THE RADIO CONTROLLED CLOCK
1.After the batteries are installed. The clock will
automatically search the radio signal. It takes about
3-5 minutes to finish this process.
2. If user wishs to disable the auto-reception feature, holds
the “Up” front panel) for 2 seconds to disable it.
3. To enable the auto-reception feature again, holds the “Up”
for 2 seconds again to force it receive and allow it receive
at desired time.
4.If the radio signal is received, the date & time will be set
automatically with radio control signal icon [ ] turns on.
5.If the clock fails to receive the time signal, it will be show
as [ ] icon. Then user can set the time manually.
CALENDAR CLOCK DISPLAY MODES
The clock and the calendar share the same section of the
display. The calendar is displayed in a day-month format.
Each press on the MODE button will change the display
between clock with second, clock with day of week, zone
time with day of week.zone time with second and day-month.
HOW TO USE AND SCAN THE MOON PHASE
The product is equipped with a moon phase display and
scanner with which eight moon phases are displayed on the
screen from new moon to waning crescent. The one falls
on the current day will flash on the screen.
If it is a full moon or new moon day, the icon will flash faster.
The eight phases are:
To check the moon phase for a particular day, press the UP
or DOWN button once. The clock will enter moon phase
scanning mode.
Use the UP or DOWN button to locate the date you want
to check. The calendar will be day-driven in this mode.
You can go back 39 days travel to next 39 days.
The corresponding moon phase will appear immediately
on the screen.
The unit will return to the last display mode when the UP
and DOWN buttons are left idle for 2 seconds.
DISCONNECTED SIGNALS
If without obvious reasons the display of the outdoor
temperature goes blank, Hold [ ] for 2 seconds to enforce
an immediate search.
If that fails, check:
1. The remote unit is still in place.
2.
The batteries of both the remote unit and main unit.
Replace as necessary.
Note: When the temperature falls below freezing point, the
batteries of outdoor units will freeze, lowering their voltage
supply and the effective range.
3.The transmission is within range and path is clear of obstacles
and interference. Shorten the distance when necessary.
New
Moon
Waning
Crescent
Waning
Crescent
First
Quarter
Waxing
Gibbous
Full
Moon
Waning
Gibbous
Last
Quarter
HOW TO SET THE CLOCK MANUALLY
To set the clock manually, hold MODE for two seconds it
will show the year. Use [ ] or [ ] to change it.
Press MODE to confirm. Repeat the same procedure to set
display language, ˚C/˚F, year, month, date, date-month
format, 12/24, hour and minute.
During the setting, press and hold [ ] or [ ] will
increase or decrease the value rapidly.
For display language, you can choose among English (En),
German(DE), French(Fr), Italian (IT) and Spanish (SP) -
in that order.
If there is an item you do not wish to change, simply press
[ MODE ] to bypass the item.
When you finished the change, press [ MODE ] to exit.
The display will return to the clock mode.
HOW TO SET AND ARM THE ALARM
To set an alarm,
1. Press [ALARM] once to display alarm time. If the alarm
is disarmed, the time will be displayed as “ OFF ”.
2. Hold [ALARM] for two seconds. The hour digits will blink.
3. Enter the hour using [ ] or [ ].
4. Press [ALARM]. The minute digits will blink.
5. Enter the minutes using [ ] or [ ].
6. Press [ALARM] to exit.
7. Repeat the same procedure to set other alarm.
ALARM FEATURE
*Weekday Alarm
The alarm sound will be activated and the icon will be
flashed on weekday when it is armed and the alarm time
is reach.
*Single Alarm
The alarm sound will be activated and the icon will be
flashed once when it is armed and the alarm time is reach.
Once it finished, it will be disabled automatically.
*Pre-Alarm
The pre-alarm sound will be activated and the icon will be
flashed if outdoor temperature under or equal two degree C.
Which is programmable 15, 30, 45, 60 or 90 minutes earlier
than the weekday alarm or single alarm time.
HOW TO SET THE ZONE TIME
To set the zone time,
1. Press [MODE] until at zone time display mode,
2. Hold [MODE] for two seconds, the zone time offset will
be displayed.
3. Enter the offset using [ ] or [ ].
4. Press [MODE] to exit.
The alarm “ ” “ ” and “ Pre-AL” icons will be
displayed indicating which alarm is armed. You can also arm
or disarm an alarm by pressing the [ ],[ ] button at alarm
display mode.
Press MODE to return to clock display mode.
SNOOZE FEATURE
When the alarm sound is on, press the snooze key enter
snooze mode. After 8 minutes, alarm sound will be wake up
automatically. The snooze cycle will be restarted if you
press the snooze key again.
If you leave the alarm sound on for 2 minutes, it will enter
snooze mode automatically with maximum 3 times.
HOW TO STOP AN ALARM
Press [ALARM] on the unit to stop an alarm.
W S
