Garmin PANOPTIX User manual

PANOPTIX™ICE FISHING KIT

INSTALLATION INSTRUCTIONS

Assembling the Portable Mount

You need a Phillips screwdriver to assemble the portable mount.

1Insert the handle into the two openings on the portable mount base .

2Secure the handle to the base using the two 42 mm machine screws and two nuts .

3Slide the included hook and loop straps through the narrow slots beside the battery compartment.

4If you are installing a Panoptix LiveScope™ sonar module , using the eight included 21 mm screws , split

washers, and flat washers, attach the two included brackets to the module, and secure the brackets to

the portable mount.

5Align the chartplotter bail mount over the hole pattern that matches your bail mount, with the openings on

the top of the bail mount facing the back of the base.

GUID-C5E8D7D2-C09F-45FD-82BF-4470A5CE1713 v2March 2021

6Secure the device mount to the base using the four included 24 mm machine screws and the included

washers, if you are installing a metal bail mount.

NOTICE

Only use the included washers if you are installing a metal bail mount. If you are installing a plastic bail

mount, do not use the four included washers.

NOTE: Do not use the self-threading screws included with the chartplotter. Only use the machine-threaded

screws included with this portable kit or use M4 machine screws.

7Place the included rubber washers on the bail-mount knobs, and screw the knobs into the sides of the cradle

or chartplotter.

8Place the cradle or chartplotter into the bail mount, with the rubber washers between the knobs and the

cradle, and tighten the knobs.

The rubber washers enable you to adjust the viewing angle without adjusting the knobs.

9Place the battery (not included) into the battery compartment under the handle.

10 Pull the straps under and around the bottom of the portable mount, and wrap them tightly around the

battery.

Placing the Portable Mount in the Bag

After you have assembled the portable mount, you should place it in the bag, which makes it easier to carry and

protects it from the elements. The bag contains loops that allow you to tether the bag as needed.

1Place the portable mount into the bag.

2If necessary, wrap the excess power cable and transducer cables around the handle.

3Close all of the zippers.

You can use the zipper at the back of the bag for quick access to charge the battery. You can store the wall

charger in the interior zippered pocket, and store the transducer in the exterior side pocket.

Connecting the Cables

CAUTION

Ensure that you connect the correct spade connector to the correct battery terminal. Damage to the battery or

device, or bodily harm may occur if the device is improperly connected to the battery (not included).

1Obtain an appropriate power cable and transducer cable to use with your chartplotter and transducer.

The all-in-one power and transducer cable (010-12676-40) works with 7 inch or larger ECHOMAP™

chartplotters.

2Connect the 4-pin power cable and transducer cable to the chartplotter.

3If you are connecting a transducer, connect the power leads to the gray bare wire connectors on the power

cable.

4If you are connecting a Panoptix LiveScope sonar module, connect the 2-pin power cable to the sonar

module.

5Slide the red spade connector onto the positive (red) terminal on the battery.

6Slide the black spade connector onto the negative (black) terminal on the battery.

Limited Warranty

The Garmin® standard limited warranty applies to this accessory. For more information, go to www.garmin.com

/support/warranty.html.

Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. LiveScope™ and Panoptix™ are trademarks of

Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.

Table of contents

Other Garmin Fish Finder manuals

Garmin

Garmin Fishfinder 100 Blue User manual

Garmin

Garmin GPSMAP 580 User manual

Garmin

Garmin CS 1522 User manual

Garmin

Garmin Fishfinder 400C User manual

Garmin

Garmin Fishfinder 120 User manual

Garmin

Garmin echoMAP CHIRP 70 series User manual

Garmin

Garmin Fishfinder 160C User manual

Garmin

Garmin GWS 10 Marine Wind Sensor User manual

Garmin

Garmin Fishfinder 160 Blue User manual

Garmin

Garmin GPSMAP 12 2 Series User manual

Garmin

Garmin Fishfinder 400C Reference guide

Garmin

Garmin Fishfinder 240 Blue User manual

Garmin

Garmin STRIKER Vivid 4 User manual

Garmin

Garmin GPSMAP 185 Sounder User manual

Garmin

Garmin Fishfinder 90 Reference guide

Garmin

Garmin Fishfinder 140 User manual

Garmin

Garmin Fishfinder 140 User manual

Garmin

Garmin STRIKER VIVID User manual

Garmin

Garmin echo 300c User manual

Garmin

Garmin striker 4 User manual

Garmin

Garmin 90 User manual

Garmin

Garmin echo 200 Series User manual

Garmin

Garmin Fishfinder 80 User manual

Garmin

Garmin Fishfinder 240 Blue User manual

Popular Fish Finder manuals by other brands

Norcross

Norcross D10DX.01T Installation and operation manual

Hawkeye Mfg

Hawkeye Mfg FishTrax FT1PXC Operation manual

JRC

JRC JFV-700HP instruction manual

JRC

JRC FF50 instruction manual

Navman

Navman FISH 4200 Installation and operation manual

Humminbird

Humminbird 140c Fishin' Buddy user guide

Furuno

Furuno FCV-628 Operator's manual

Humminbird

Humminbird Tour Series Operation manual

Humminbird

Humminbird 585C Operation manual

Humminbird

Humminbird 595C Operation manual

Raytheon

Raytheon V720 instruction manual

Humminbird

Humminbird 400TX Operation manual

Norcross

Norcross ML100TDR ML100R ML100DR ML100tr instruction manual

Furuno

Furuno FCV-627 Operator's manual

Fuso

Fuso FEG-881 Operation manual

Humminbird

Humminbird Matrix 47 installation guide

Humminbird

Humminbird PiranhaMAX 165 Installation and operation manual

Humminbird

Humminbird 586C Operation manual