GAE CMFD Operational manual

P.O. Box 580816 ♦Modesto, CA 95358
Product User Manual
♦♦
EPRI Commercial Microwave Fabric
Dryer
Document # 930001, Rev. 2
July 1999

Product User Manual Page 2
EPRI Commercial Microwave Fabric Dryer
Gerling Applied Engineering, Inc. Modesto, CA
REVISION HISTORY
REV. DESCRIPTION DATE APPROVAL
1DOCUMENT WAS NUMBER ON10051 27MAR99 JFG
2ADDED CYCLE TIMER 23JUL99 JFG
WARRANTY
Products manufactured and sold by Gerling Applied Engineering, Inc. (“GAE”) are
warranted to be free of defects in materials and workmanship under normal use and
service for a period of twelve (12) months from the date of original shipment. GAE’s
obligation under this warranty is limited to repairing or replacing, at GAE’s option, all
non-consumable component parts. Consumable parts are specifically excluded from
this warranty and may include, but are not be limited to, magnetrons, fuses, lamps,
seals, o-rings, v-belts, and fluids. All warranty repairs are to be done at GAE’s facility or
as otherwise authorized by GAE. All shipping charges for warranty repair or
replacement are the purchaser’s responsibility unless otherwise agreed to by GAE.
This warranty supercedes all other warranties, expressed or implied. No warranty is
given covering the product for any particular purpose other than as covered by the
applicable product specifications. GAE assumes no liability in any event for incidental or
consequential damages, financial losses, penalties or other losses incurred in
conjunction with the use of GAE products.
DOCUMENT CONVENTIONS
NOTE:Means the reader should take note. Notes contain
helpful information, suggestions, or references to other sections,
chapters, or documents.
CAUTION: Means the reader should be careful. You are doing
something that might result in equipment damage or loss of data.
WARNING: Means danger. A situation exists that could cause
bodily injury or death. All personnel must be aware of the hazards
involved with high voltage electrical circuitry and high power
microwave devices.

Product User Manual Page 3
EPRI Commercial Microwave Fabric Dryer
Gerling Applied Engineering, Inc. Modesto, CA
WARNING
The microwave dryer described in this manual is capable of producing a microwave field
that is potentially hazardous to operating personnel. The unit must never be connected
or operated in a manner that allows a field in excess of 10 milliwatts per square
centimeter to be generated in an area accessible to operating personnel. Contact GAE,
Inc. for technical support prior to installation and/or operation of these units if there is
any question or concern about microwave leakage.
All electrical cable connections must be secure prior to operation. Never operate the
microwave dryer without a properly rated absorbing load inside the oven cavity. To
ensure safe operation and prevent microwave leakage, the equipment must be
periodically inspected and maintained as required or recommended.

Product User Manual Page 4
EPRI Commercial Microwave Fabric Dryer
Gerling Applied Engineering, Inc. Modesto, CA
TABLE OF CONTENTS
INTRODUCTION.............................................................................................................5
GENERAL DESCRIPTION..............................................................................................6
Electrical Specifications 7
Mechanical Specifications 7
Controls 7
Sensors 7
INSTALLATION ..............................................................................................................8
Preliminary Inspection 8
Facilities Requirements 8
Location 8
Electrical Connections 8
BASIC OPERATION.....................................................................................................10
Initial Power-Up 10
Dryer Loads 10
Drying Cycle Setting 11
Cycle Start 11
Cycle Stop 12
Sensor Lint Screen Burn-off 12
Fault Cycles 12
Lint Screen Cleaning 13
THEORY OF OPERATION ...........................................................................................14
Dielectric Heating 14
Microwave Power Generators 14
Field Strength Sensor 15
Arc Detector 16
Exhaust Humidity Sensor 16
Exhaust Gas Sensors 17
Magnetron Thermal Cutouts 17
Sensor Lint Screen Burn-off 17
Low Voltage Power Supplies 18
Drive Motors 18
USER MAINTENANCE.................................................................................................20
Lint Screen Cleaning 20
PROCESS DATA COLLECTION..................................................................................21
Terminal Emulator Data Logging 21
MS Excel Spread Sheet Data Logging 21
ATTACHMENTS:
Document Type Number Title
Drawing 910037 Outline Drawing
Drawing 910038 Block Diagram, Control System
Drawing 910048 Schematic Diagram, Comm Mw Fabric Dryer
Drawing 910049 Schematic Diagram, Microprocessor Interface
Drawing 910050 Line Power Distribution Diagram

Product User Manual Page 5
EPRI Commercial Microwave Fabric Dryer
Gerling Applied Engineering, Inc. Modesto, CA
INTRODUCTIONThe EPRI Commercial Microwave Fabric Dryer (“CMFD”) was
designed and constructed by AGL, Inc. under contract from the
Electric Power Research Institute for the purpose of on-site
demonstration and evaluation of the microwave fabric drying
process. However, prior to completion of construction of the CMFD
the contract was terminated with AGL and funding for the dryer
development program at EPRI was temporarily halted.
During its hiatus the dryer program was transferred to GAE, Inc. to
await funding for completion of construction and general
refurbishment of the CMFD. Renewed interest in the program
focused around potential industrial applications in textiles
manufacturing. A contract was awarded to GAE to complete the
dryer’s construction and deliver it for on-site installation and
operation.
While most of the dryer’s original functionality remains intact,
certain functions and features have been altered or deleted from
the original design specification due to discrepancies or conflicts in
their operation. Some of these alterations were necessitated
because of insufficient time and/or funding in the current program to
adequately resolve the issues, while others are required in order to
address inherent deficiencies in the original design. These changes
are identified and discussed in detail within this Manual where
applicable.
NOTE:While GAE has made extensive efforts to ensure safe
and reliable operation of the CMFD, Gerling Applied Engineering,
Inc. hereby disclaims all responsibility or liability for poor reliability,
unsatisfactory performance, unsafe operation or any other problem
associated with the design and construction of the CMFD.
Operators and end-users assume all risks associated with
operation of the CMFD.
WARNING: Lethal voltages may exist inside the CMFD during
operation and non-operation. All maintenance and service must be
done by qualified technical personnel only. Under no circumstances
should untrained or unskilled personnel be allowed access inside
the CMFD.

Product User Manual Page 6
EPRI Commercial Microwave Fabric Dryer
Gerling Applied Engineering, Inc. Modesto, CA
GENERAL DESCRIPTION
The EPRI Commercial Microwave Fabric Dryer (“CMFD”) is
designed for field trials of the microwave fabric drying process in
commercial establishments to dry fabric loads up to 12 pounds. It
combines microwave energy with conventional hot air to dry almost
any type of fabric load at faster rates and lower temperatures than
conventional dryers using hot air alone. A microprocessor control
system coordinates operation of the dryer by collecting data from a
variety of sensors to optimize performance and ensure safety.
The microwave energy is supplied by three separate 1.8 kW
generators for a total microwave power input of 5.4 kW. Hot air is
provided by three separate 1.5 kW duct heaters. Energy efficiency
is maximized by recycling the waste heat from the microwave
generators and other heat producing electronics, providing a total
hot air capacity of approximately 6.5 kW.
Selectable drying cycles include Regular and Delicate (the Dryness
selector has been disabled). The Regular drying cycle combines
microwave energy with hot air and cuts the drying time to 1/3 that of
conventional dryers. The Delicate cycle eliminates hot air altogether
and uses only microwave to provide the lowest temperature drying.
The CMFD includes state-of-the-art safety features to protect both
the dryer and operator from improper operation and use. A variety
of sensors are provided to detect the presence of improper
materials in the drying load and shut off the dryer. An indicator is
provided on the control panel to warn the operator to check the
load. Additional sensors are provided to monitor the dryer operation
and performance and shut off the dryer in the event of malfunction.
Facilities requirements for the CMFD are the same as those for
conventional commercial dryers. The input line power required is
208-220 VAC, single phase, 60 Amps, and the exhaust connection
is to a standard 4” diameter duct. No cooling or gas connections
are required.

Product User Manual Page 7
EPRI Commercial Microwave Fabric Dryer
Gerling Applied Engineering, Inc. Modesto, CA
Electrical Specifications
Microwave Power 5.4 kW (nominal) provided by three 1.8 kW
generators
Magnetrons Hitachi 2M130
Hot Air 6.5 kW (approx.) provided by three 1.5 kW duct
heaters plus 2 kW from recycled waste heat
Line Power Input 208-220 VAC, Single Phase, 60 Amps (2-wire
plus ground)
Mechanical Specifications
Basket Size 26” diameter x 20” deep
Basket Capacity 12 Pounds (dry weight, 100% moisture
retention)
Door Opening 16” Wide x 10” High
Exhaust Duct 4” Diameter
Free Air Displacement 175 CFM (approximate)
Overall Dimensions 30” High x 36” Deep x 62” High
Weight (approx.) 700 lb. net; 960 lb. shipping
Controls
Cycle Start Pushbutton
Cycle Stop Pushbutton
Cycle Select 3-position rotary switch for “Regular” and
“Delicate” settings (“Permanent Press” setting
has been disabled)
Dryness (Disabled)
Fault Indicators “Check Load”, “Arc Detect”
Cycle Timer Programmable timer initiates “End of cycle”
routine upon time-out
Sensors
Dryer Operation Exhaust air thermostat, exhaust air relative
humidity, exhaust air temperature (Moisture
contact sensor has been disabled)
Thermal Cut-outs Magnetrons (3), duct heaters (3), exhaust air
Safety Door interlock switches, microwave field
strength detector, arc detector, exhaust gas
sensors

Product User Manual Page 8
EPRI Commercial Microwave Fabric Dryer
Gerling Applied Engineering, Inc. Modesto, CA
INSTALLATION
Preliminary Inspection
Upon arrival at the installation site the CMFD should be thoroughly
inspected for damage or wear caused during shipping. Any visible
damage to the shipping crate or CMFD should be noted and
reported immediately to the shipping company in accordance with
standard claims procedures. Prior to connecting line power the
outer covers should be removed and all electrical connections
inspected for loose or disconnected wires. All mechanical
components should also be inspected for any loose or broken
hardware or other wear that may have been caused during
shipping.
Facilities Requirements
•Line Power: 208-220 VAC, 60 Hz, single phase, 60 Amps, 2-
wire plus ground. Proper earth ground must be provided. Please
note that, while an internal line filter is provided, the CMFD has
not been tested for immunity to noise, spikes or other line power
conditions that may be present in typical industrial
environments. A line conditioner and/or regulator may be
required for satisfactory operation of the CMFD.
•Exhaust Duct: Standard 4” diameter dryer exhaust duct. Back
pressure must be minimized.
•Environment: Indoors only, must be clean and dry. The
allowable extremes of ambient temperature and humidity have
not been tested and are thus unknown. Ambient conditions
should be maintained as close to mid-range as possible to
ensure reliable operation.
Location The CMFD may be installed and operated on any level surface.
Adequate clearance must be provided on the sides and front near
the louvered ducts to allow sufficient intake of dryer air.
Electrical Connections
•Line Power: A 4-conductor Hubbell ‘Twist-lock’ type connector is
provided at the back of the CMFD. Connections are to two
phases plus ground with no neutral connection. A mating
connector and power cord is also provided. Pinouts are as
follows:
XPhase A (any of three phases)
Y Phase B (either of remaining two phases)

Product User Manual Page 9
EPRI Commercial Microwave Fabric Dryer
Gerling Applied Engineering, Inc. Modesto, CA
GGround
WNo connection (normally used for neutral)
•Line Current Monitoring: An 11-pin ‘MS’ style circular connector
(J1) located on the back of the CMFD provides three separate
analog voltage signals that are proportional (10VDC = 100A) to
the line current drawn by corresponding subsystems within the
CMFD. A mating connector is also provided. Pinouts are as
follows:
Pins A (+) and B (-) Microwave power supply current
Pins C (+) and D (-) Basket and blower drive motors current
Pins D (+) and E (-) Duct heaters current (output disabled)
Pins F and H Not used (reserved for later use)
Pins K, L and M No connection

Product User Manual Page 10
EPRI Commercial Microwave Fabric Dryer
Gerling Applied Engineering, Inc. Modesto, CA
BASIC OPERATION
Operation of the CMFD is very similar to that of a conventional
residential clothes dryer. A typical sequence of events is as follows:
•Load fabrics to be dried and close door
•Select drying cycle
•Press ‘Start’ button to begin drying
•Wait for buzzer signaling end of drying cycle
•Open door and remove dried fabrics
While this operation sequence appears to be relatively simple,
there are many subtle aspects of the CMFD’s operation as
explained below that should be fully understood by the operator.
Initial Power-Up After connecting line power as described in the “Installation” section
of this manual, power is applied to the CMFD by lifting the circuit
breaker handle located near the line power connector on the back
panel. This applies power to various low voltage power supplies
which in turn supply power to the microprocessor and other
controls.
NOTE:One of the subsystems to which initial power is applied is
the suite of four separate gas sensors. These sensors require a
warm-up period of approximately one hour for stable performance.
Line power can remain on indefinitely, so there is no need to turn
off and disconnect line power between daily periods of operation.
However, as a safety precaution it is recommended that line power
be disconnected during extended periods of non-operation.
Dryer Loads The CMFD is designed to accommodate most typical fabrics used
in clothing or other standard textile products. However, it should be
noted that some fabrics may contain certain materials that will
result in fault conditions during the drying process. While the CMFD
is designed to protect itself and the operator from such loads, the
operator should take necessary precautions to avoid loads
containing the following materials:
•Metallic fabrics such as woven metal screens
•Metallic or metalized threads
•Heavily studded, sequined or ornamented fabrics (a few metal
studs or metal zippers are generally OK)
Table of contents

















