Furuno GP-150 User manual

INSTALLATION MANUAL

GPS NAVIGATOR

GP-150

1. SYSTEM CONFIGURATIONS .......................................................................... 1

2. EQUIPMENT LIST............................................................................................ 2

3. DISPLAY UNIT .................................................................................................. 4

4. ANTENNA UNIT ................................................................................................ 6

5. WIRING ........................................................................................................... 10

6. INITIAL SETTINGS ......................................................................................... 12

7. OPTIONAL DGPS........................................................................................... 23

PACKING LISTS & INSTALLATION MATERIALS........................................... A-1

OUTLINE DRAWINGS ...................................................................................... D-1

INTERCONNECTION DIAGRAM ......................................................................S-1

www.furuno.co.jp

SAFETY INSTRUCTIONS

WARNING

Do not work inside the

equipment unless totally

familiar with electrical

circuits.

Hazardous voltage which can

cause electrical shock, burn

or serious injury exists inside

the equipment.

Turn off the power at the

mains switchboard before

beginning the installation.

Post a sign near the switch

to indicate it should not be

turned on while the equip-

ment is being installed.

Fire, electrical shock or

serious injury can result if the

power is left on or is applied

while the equipment is being

installed.

Ground the display unit to

prevent loss of sensitivity

and mutual interference.

Confirm that the power supply voltage

is compatible with the voltage rating

of the equipment.

Connection to the wrong power supply

can cause fire or equipment damage. The

voltage rating appears on the label at the

rear of the display unit.

Use the correct fuse.

Use of a wrong fuse can cause fire or

equipment damage.

Keep the following compass safe

distances:

Standard Steering

Display unit 0.50 m 0.35 m

CAUTION

This page is intentionally left blank.

1. SYSTEM CONFIGURATIONS

Antenna Unit GPA-018S*

Display Unit

Radar, Echosounder,

Autopilot etc.

DGPS Beacon

Receiver

GR-80**

12-24VDC

Antenna Unit GPA-017S**

Antenna Unit GPA-019S*

*: w/internal beacon receiver

**: w/o internal beacon receiver

2. EQUIPMENT LISTS

Standards

Name Type Q'ty Remarks

GPA-017S

GPA-018S

Antenna Unit

GPA-019S

1 For DGPS

GP-150-E-N Without Beacon RX

Display Unit GP-150-E-A 1 With Beacon RX

CP20-01900 With Antenna CableInstallation

Materials CP20-01950 1 set Without Antenna Cable

Accessories FP20-01100 1 set

Spare Parts SP20-00500 1 set

See lists

at end of

manual.

Options

Name Type Code No. Remarks

Flush Mount Kit S OP20-24 004-393-000

Flush Mount Kit F OP20-25 004-393-280 For display unit.

CP20-01700 004-372-110 CP20-01701+30 m cable

CP20-02700 004-381-160 CP20-02701+30 m cable

CP20-01710 004-372-120 CP20-01701+50 m cable

Antenna Cable Set

CP20-02710 004-381-170 CP20-02701+50 m cable

Antenna Cable Assy. TNC-PS-3D-15 000-133-670 15 m

Right Angle Antenna

Base No.13-QA330 000-803-239

L-Type Antenna Base No.13-QA310 000-803-240

Handrail Antenna Base No.13-RC5160 000-806-114

Mast Mount Kit CP20-01111 004-365-780

For antenna unit.

MJ-A6SPF0011-050C

(03S9202) 000-159-690-10 Cross Cable 5m, 6P-4P

MJ-A6SPF0011-100C

(03S9226) 000-159-691-10 Cross Cable 10m, 6P-4P

MJ-A7SPF0003-050C

(20S0241) 000-159-688-11 5m, For DATA4

MJ-A6SPF0003-050C

(20S0093) 000-154-054-10 5m

MJ-A6SPF0012-050C

(64S4073) 000-154-053-10 Cross cable 5m

Cable Assy

MJ-A6SPF0012-100C

(64S4071) 000-154-037-10 Cross cable 10m

2. EQUIPMENT LISTS

(Continued from the previous page)

OP20-32-1 000-041-018 With GPA-018S

OP20-32 000-041-019 With whip antenna and OP20-32-1

OP20-33 000-041-596 With GPS-019S

Beacon Receiver Set

OP20-34 000-041-598 Without whip antenna

000-013-485 For 100VAC mains

Rectifier PR-62 000-013-486 For 220VAC mains

DGPS Beacon Receiver GR-80 -

Whip Antenna FAW-1.2 000-130-046 1.2 m

Printer PP-505-FP 000-011-792

Data Switch Box MD-200 -

3. DISPLAY UNIT

The display unit can be installed with either of four methods as shown below. Refer to the

outline drawing at the end of manual.

• Locate the unit away from exhaust pipes and vents.

• The mounting location should be well ventilated.

• Mount the unit where shock and vibration are minimal.

• Keep the display unit away electromagnetic field generating equipment such as motor,

generator.

• Allow sufficient maintenance space and a sufficient slack in cables for maintenance and

repair.

Table Top and Overhead Mounting

TABLETOP OVERHEAD

Display unit mounting methods

Flush mounting type F

An optional flush mount kit type F is required. For details, see outline drawing at end of this

manual. (Name: Flush Mount Kit F, Type: OP20-25, Code No.004-393-280)

Name Type Code No. Qty

Self-tapping screw 5X20 000-162-609-10 4

Hex. bolt M6X12 SUS304 000-162-897-10 2

Spring washer M6 SUS304 000-158-855-10 2

Cosmetic panel 20-013-1121 100-234-240 1

3. DISPLAY UNIT

Flush mounting type S

An optional flush mount kit type S is required. (Name: Flush Mount Kit S, Type: OP20-24,

Code No.: 004-393-000)

Name Type Code No. Qty

Wing bolt M4X30 YBSC2 000-804-799 4

Hex. bolt M6X12 SUS304 000-162-897-10 2

Wing nut M4 YBCS2 000-863-306 4

Spring washer M6 SUS304 000-158-855-10 2

Flush mount metal 20-013-1111 100-234-230 2

1. Prepare a cutout in the mounting location whose dimensions are 242 (W) X 152 (H) mm.

2. Insert the unit to the cutout.

3. Attach two flush mount metals to the unit with two hex bolts (M6X12) and two spring

washers.

4. Screw four wing bolts to wing nut.

5. Fasten the unit with wing bolts assembled at step 4, and then tighten nuts.

4. ANTENNA UNIT

Mounting

Install the antenna unit referring to the installation diagram at end of manual. When

selecting a mounting location for the antenna unit, keep in mind the following points.

• Select a location out of the radar beam. The radar beam will obstruct or prevent reception

of the GPS satellite signal.

• Be sure the location offers a clean line-of-sight to satellite. Objects within line-of-sight to

a satellite, for example, a mast or funnel, block reception and cause prolonged acquiring time

or interruption of position fix.

• Mount the unit as high as possible. Mounting the antenna as high as possible keeps it free

of water spray, which can intercept reception of GPS satellite signal, if water spray is frozen.

• The antenna unit GPA-018S must be grounded. Connect ground wire of 1.25 sq or larger

(local supply) between the antenna unit and a stainless steel screw fastened to the mast.

• The antenna unit GPA-018S must be taped. See next page.

• The antenna unit should be fixed to the mast as below.

Coat here with silicone sealant to

prevent breakage of the cable by

vibration.

Wrap the vinyl sheet to prevent

the breakage of the cable, and

then fix it with a hose clamp.

Other manuals for GP-150

Table of contents

Popular GPS manuals by other brands

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Operating instruction

Garmin

Garmin SOUNDER 125 Owner's manual & reference

Garmin

Garmin DEZL 580 owner's manual

Jigabot

Jigabot EX quick start guide

Pointer

Pointer Cellocator CelloTrack XT LTE overview

Queclink

Queclink GV55LITE user manual

Voxson

Voxson Voxtrack GPS500 Quick user guide

Garmin

Garmin ECHOMAP PLUS owner's manual

Starcom Systems

Starcom Systems Kylos Compact user guide

Garmin

Garmin 15 H Series Technical specifications

Cobra

Cobra Marine MC 600Ci owner's manual

Cellocator

Cellocator CelloTrack T installation guide

Enfora

Enfora Mini-MT GSM2228UG001 user guide

Magellan

Magellan eXplorist 100 Reference manual

LTE

LTE G50B user manual

Garmin

Garmin DEZL OTR500 owner's manual

SkyGolf

SkyGolf SkyCaddie SG1 user guide