Fujitsu P2711 TE QHD Installation instructions
Page 1 of 14
Disassembly and Repair 2
Information on the installation and removal of components 3
Tools 4
Disassembly 5
P2711 TE/TS QHD Monitor Exploded Drawing 10
P2711 TS CAM Monitor Exploded Drawing 11
Replaceable Components and Services 12
Disposal information for recycling companies 13
Disassembly and repairs
Display P2711 TE QHD
Display P2711 TS QHD
Display P2711 TS
CAM
Version date 12.01.2023
Category Disassembly and repairs
Contents
Page 2 of 14
Disassembly and Repair
We recommend printing out the relevant sections of this chapter prior to installation
as the device for installing/removing hardware components needs to be switched off.
In order to repair the display, please follow the disassembly instructions to remove the defect part, replace it with spare part, then follow the
instructions in reverse order.
If you have received any further documents with your device, you should read these through carefully.
Please note the following instructions before installing/removing system components:
■ The device must be switched off when installing/removing components and it must
not be in power-saving mode.
■ Disconnect the mains plug before opening the device.
■ After unplugging the mains plug, discharge the remaining voltage by pressing the
activation button.
■ Remove all externally connected cables.
■ Take care not to flex foil cablech any cables when installing/removing components.
■ Please ensure that the installed components that might heat up intensely during
operation do not exceed the permitted operating temperature.
!
Page 3 of 14
Information on the installation and removal of components
Please pay attention to the locking mechanism (indentations and centring flex foil cables) when installing hardware components.
Note that some components on the mainboard may be very hot if the device was in use shortly before the case was removed.
Utmost care is required during installation and removal to avoid damaging components.
Never use items with sharp edges (screwdrivers) to lever them out.
Parts with Electrostatic Sensitive Devices (ESD) can be identified by a corresponding label.
When dealing with boards with ESDs, the following points must always be observed:
■ Always ensure there is a static discharge (e.g. by touching a grounded object) prior to commencing
with the work.
■ The devices and tools being used must not be statically charged.
■ Only touch the components along the edges or on the areas marked in green (contact points).
■ Contacts and electronic components must not touch when handling components equipped with ESD
protection.
Page 4 of 14
Tools
Screwdriver: Pozidriv PZ 2
Screwdriver: Phillips PH 1
Hexagon Screwdriver size 5
Flat Head Screwdriver
Page 5 of 14
Disassembly
Step Figure Description
Remove the
Stand Base
Ass'y.
Remove the
screws to
remove the
stand base
assy.
Remove the
rear cover
Remove the
rear cover
Disconnect
the flex foil
cable.
Disconnect the
flex foil cable
to remove the
rear cover.
Page 6 of 14
Remove the
tapes and the
flex foil cable
Remove the
tapes and the
flex foil cable
Remove the
screws to
remove the
middle frame
and the panel
Remove the
screws to
remove the
middle frame
and the panel
Take off the
tape and
disconnect
the flex foil
cable
Take off the
tape and
disconnect the
flex foil cable
Page 7 of 14
Remove the
main board
and power
board
Remove the
screws to
remove the
main board and
power board
Remove the
connectors
Remove the
connect flex foil
cables
Remove the
speakers
Remove the
speakers
Page 8 of 14
The panel
The panel
The WEBCAM
Remove the
screws to
remove the
WEBCAM
The key board
Remove the
screws to
remove the key
board
Page 9 of 14
The middle
frame
The middle
frame
The USB
board
Remove the
screw to
remove the
USB board.
The Rear
Cover
The Rear
Cover
Page 10 of 14
P2711 TE/TS QHD/CAM Monitor Exploded Drawing
This manual suits for next models
2
Table of contents
Other Fujitsu Monitor manuals
Fujitsu
Fujitsu Plasmavision PDS4211 User manual
Fujitsu
Fujitsu P42XTA51US User manual
Fujitsu
Fujitsu L21T-1 User manual
Fujitsu
Fujitsu B22W-6 LED User manual
Fujitsu
Fujitsu L20T-1 ECO User manual
Fujitsu
Fujitsu E22W-6 LED User manual
Fujitsu
Fujitsu Plasmavision W P42HHA30E User manual
Fujitsu
Fujitsu P2410 Series User manual
Fujitsu
Fujitsu Plasmavision P42VCA10 User manual
Fujitsu
Fujitsu Zero Client DZ19-2 User manual
Fujitsu
Fujitsu 17inch User manual
Fujitsu
Fujitsu SCALEOVIEW C17-7 User manual
Fujitsu
Fujitsu x150f User manual
Fujitsu
Fujitsu SCENICVIEW A17-3 User manual
Fujitsu
Fujitsu FUTRO DC20-1 User manual
Fujitsu
Fujitsu P24W-6 User manual
Fujitsu
Fujitsu Plasmavisioin User manual
Fujitsu
Fujitsu P23T-6 IPS User manual
Fujitsu
Fujitsu PLASMAVISION P50XCA51WH User manual
Fujitsu
Fujitsu plasmavision User manual
