FujiFilm X-Pro1 User manual
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
1
X-Pro1
CAUTION
BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIGNATED
AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN
PERFORMING REPAIRS. (Refer to page 3)
WARNING
THE COMPONENTS IDENTIFIED WITH THE MARK " " ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.
IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN ELECTRICAL
SHOCK.
Ref. No.: ZM00984-109
Revised on 17 Oct 2013
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
2
SAFETY CHECK-OUT
After correcting the original problem, perform the following
safety check before return the product to the customer.
1. Check the area of your repair for unsoldered
or poorly soldered connections. Check the
entire board surface for solder splasher and
bridges.
2. Check the interboard wiring to ensure that no
wires are "pinched" or contact high-wattage
resistors.
3. Look for unauthorized replacement parts,
particularly transistors, that were installed
during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, though functioning, show
obvious
signs of deterioration. Point them out to the
customer and recommend their replacement.
5. Check the B + voltage to see it is at the values
specified.
6. Make leakage - current measurements to
determine that exposed parts are acceptably
insulated from the supply circuit before
returning the product to the customer.
7. CAUTION: FOR
CONTINUED PROTECTION
AGAINST FIRE HAZARD,
REPLACE ONLY WITH
SAME TYPE 2.5 AMPERES
125V/250V FUSE.
ATTENTION: AFIN
D'ASSURER UNE
PROTECTION
PERMANENTE CONTRE
LES RISQUES D'INCENDIE,
REMPLACER
UNIQUEMENT PAR UN
FUSIBLE DE MEME, TYPE
2.5 AMPERES, 125/250
VOLTS.
8. WARNING:
TO REDUCE THE
ELECTRIC SHOCK, BE
CAREFUL TO TOUCH THE
PARTS.
RISK OF FIRE-
REPLACE FUSE
AS MARKED
2.5A 125V/250V
2.5A 125V/250V
WARNING!
HIGH VOLTAGE
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
3
RoHS lead-free compliance
With the exception of parts and materials expressly excluded from the RoHS directive, all the internal connections and
component parts and materials used in this product are lead-free compliant under the European RoHS directive (*1). Use the
designated after-sales parts and the designated lead-free solder when performing repairs.
*1:Definition of lead-free
A lead content ratio of 0.1 wt% or less in the applicable locations (solder, terminals, electronic components, etc.)
<Lead-free soldering>
When lead-free solder is used, the solder tends to be less workable than when eutectic solder is used. When carrying out
repairs, use a designated lead-free solder, bearing in mind the differing work practices for eutectic solder and lead-free
solder.
■Differences in the soldering work for lead-free and eutectic solder
Eutectic solder (Sn-Pb) Lead-free solder
(Sn-Ag-Cu)
Remark
Melting point 183°C 220°C
Soldering iron temperature 283°C 320°C The bonding temperature that will
give the best bond strength.
Wetting Good Poor
Surface Gloss Matte
■Recommended equipment
■Soldering iron maintenance
Because of the high soldering iron temperature in lead-free soldering, there is rapid carbonization of the flux adhering to
the tip of the soldering iron.
(1) Always cover the tip of the soldering iron with solder when it is not being used.
(2) If the tip is black from carbonization, wipe it gently with a paper towel soaked in alcohol until the solder will wet.
lead-free
Wire diameter
Solder type (Displayed symbol)
SnAgCu
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
4
MEMO
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
5
CONTENTS
1. Disassembly ............................................................................................................1-1
2. Schematics ..............................................................................................................2-1
3. Adjustments ............................................................................................................3-1
4. Inspection ................................................................................................................4-1
5. Parts List 1 (Packing and Accessories) ......................................................................5-1
6. Parts List 2 (Mechanical Block) .................................................................................6-1
7. Electrical parts ........................................................................................................7-1
8. Appendix...................................................................................................................8-1
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
6
MEMO
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
1-1
1. Disassembly
1-1. Removing the CASE
(1) Remove the DECO PLATE LEVER.
(2) Remove the 1 screw.（MS2M 1.4X2.0）
(3) Remove the LEVER FINDER.
(4) Peel off the GRIP F.
(5) Peel off the TAPE GRIP F.
(6) Remove the 4 screws.（MS2M 1.7X3.5）
(7) Remove the BASE GRIP F.
2
1
4 4
55
66
7
66
5
3
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
1-2
(8) Peel off the SHEET GRIP R LEFT.
(9) Peel off the SHEET GRIP R RIGHT.
(10) Peel off the SHEET GRIP F RIGHT.
(11) Peel off the SHEET GRIP F LEFT.
(12) Peel off the SHEET FRONT.
[Assembly]
Assemble by performing the disassembly procedure in reverse.
Refer to the sheet sticking procedure.
Recycling prohibition of SHEET.
8 9
11
12
10
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
1-3
1-2. Removing the CONST REAR
(1) Remove the 1 screw.（N-MSGM 1.7X2.5）
(2) Remove the 4 screws.（N-MSGM 1.7×2.5D）
(3) Remove the 3 screws.（N-MS2M 1.7X3.0）
(4) Remove the 2 screws.（N-MSGM 1.7X4.0）
1 22
3
3
3
4
4
Confidential: FUJIFILM Service Center Use Only
X-Pro1 Service Manual
1-4
(5）Open the CONST REAR in the direction of the arrow.
(6）Remove the REAR FFC from theMAIN PWB ASSY.
(7) Peel off the ULTAPE.
(8) Peel off the CUSHION CN LCD.
(9) Unlock the connector and remove theLCD FPC.
[Assembly]
Assemble by performing the disassembly procedure in reverse.
5
6
9
7 8
Other manuals for X-Pro1
4
Table of contents
Other FujiFilm Digital Camera manuals
FujiFilm
FujiFilm X20 Owner's manual
FujiFilm
FujiFilm FinePix AX300 User manual
FujiFilm
FujiFilm FinePix HS10 User manual
FujiFilm
FujiFilm FinePix A360 User manual
FujiFilm
FujiFilm FINEPIX JX500 Series User manual
FujiFilm
FujiFilm FINEPIX SL240 SERIES User manual
FujiFilm
FujiFilm Finepix J110w User manual
FujiFilm
FujiFilm Finepix F660EXR User manual
FujiFilm
FujiFilm FinePix 2300 User manual
FujiFilm
FujiFilm FinePix30i User manual
FujiFilm
FujiFilm X100V User manual
FujiFilm
FujiFilm Instax Mini 7S User manual
FujiFilm
FujiFilm 1400 User manual
FujiFilm
FujiFilm FinePix F470 User manual
FujiFilm
FujiFilm axia ix-10 User manual
FujiFilm
FujiFilm FINEPIX Z900EXR User manual
FujiFilm
FujiFilm FinePix Z33WP User manual
FujiFilm
FujiFilm FinePix F300EXR User manual
FujiFilm
FujiFilm FinePix JX665 User manual
FujiFilm
FujiFilm FinePix S5 Pro User manual
