FS S3910 Series User manual

SET

CONSOLE

TUS PWR1 PWR2 ID

21 43 65 87 109 12

11 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 38

37 4039 4241 4443 4645 4847 5049 5251

SFP+

Green=1000M Yellow=10/100M On=Link Flashing=ACT

S3910-48TS

RESET

Green=1000M On=Link

Yellow=10/100M Flashing=ACT

CONSOLE

ATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423

25 26 27 28

SFP+

S3910-24TS

MANAGED L2+ GIGABIT SWITCHES

S3910 Series Switches

Quick Start Guide V1.0

RESET

Green=1000M On=LinkYellow=10/100M Flashing=ACT

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423

25 26 27 28

SFP+

S3910-24TS

RESET

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251

SFP+

Green=1000M Yellow=10/100M On=Link Flashing=ACT S3910-48TS

Introduction

Thank you for choosing S3910 Series Stackable Managed Switches. This guide is designed to

familiarize you with the layout of the switch and describes how to deploy the switch in your network.

S3910-24TS

S3910-48TS

Accessories

Power Cord x2 Grounding Cable x1 Rubber Pad x4

NOTE: S3910 series switches have dust plugs delivered with them. Keep the dust plugs

properly and use them to protect idle optical ports.

Mounting Bracket x2 M4 Screw x8

RESET

Green=1000M On=LinkYellow=10/100M Flashing=ACT

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423

25 26 27 28

SFP+

S3910-24TS

RESET

Green=1000M On=LinkYellow=10/100M Flashing=ACT

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423

25 26 27 28

SFP+

S3910-24TS

RESET

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251

SFP+

Green=1000M Yellow=10/100M On=Link Flashing=ACT

S3910-48TS

Hardware Overview

Front Panel Ports

Front Panel Button

CONSOLE

S3910-24TS

SFP+RJ45

RESET

S3910-24TS / S3910-48TS

CONSOLE SFP+RJ45

S3910-48TS

Ports Description

RJ45

CONSOLE

SFP+

10/100/1000BASE-T ports for Ethernet connection

SFP+ ports for 1/10G connection

An RJ45 console port for serial management

Button Description

RESET Restart: Press and hold the RESET button for more than ve seconds, and

then wait for ten seconds.

RESET

Green=1000M On=LinkYellow=10/100M Flashing=ACT

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423

25 26 27 28

SFP+

S3910-24TS

RESET

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251

SFP+

Green=1000M Yellow=10/100M On=Link Flashing=ACT

S3910-48TS

Back Panels

S3910-24TS / S3910-48TS

Front Panel LEDs

S3910-24TS

SFP+

RJ45

STATUS

PWR1 ID

PWR2

S3910-48TS

PWR1

PWR2

Dual Power Supplies Grounding Point

SFP+

RJ45

PWR1 ID

STATUS

PWR2

LEDs DescriptionStatus

STATUS

O

Blinking Green

Solid Yellow

Solid Red

Solid Green

System is being initialized.

Switch is operational.

Switch is not receiving power.

1. Severe temperature warning:

The temperature severely exceeds the temperature limit, so

the system is going to restart.

2. The switch is faulty.

Moderate temperature warning:

Check the working environment of the switch immediately.

LEDs DescriptionStatus

PWR1/PWR2

RJ45

SFP+

O

Solid Green

Solid Red

A power supply is connected and able to work.

A redundant power supply fails or no AC cable is connected.

No power supply module is connected.

O

Solid Blue

O

Locating is enabled. Operation and maintenance sta turn

on and o the LED remotely.

The port is not connected.

Solid Green The port is connected at 1000 Mbps.

Blinking Green The port is receiving or transmitting trac at 1000 Mbps.

Solid Yellow The port is connected at 10/100 Mbps.

Blinking Yellow The port is receiving or transmitting trac at 10/100 Mbps.

O The port is not connected.

Solid Green The port is connected.

Blinking Green The port is receiving or transmitting trac.

Locating is disabled.

Before you begin the installation, make sure that you have the following:

Site Environment：

Do not operate it in an area that exceeds an ambient temperature of 50°C.

Installation Requirements

Phillips screwdriver.

Standard-sized, 19" wide rack with a minimum of 1U height available.

Category 5e or higher RJ-45 Ethernet cables, ber optical cables and console cable for connecting

network devices.

Do not install the equipment in a dusty environment.

The installation site must be free from leaking or dripping water, heavy dew, and humidity.

The installation site must be well ventilated. Ensure that there is adequate airow around the

switch.

The switch should be installed at least 1U (44.45mm) away from devices to its sides.

Be sure that the switch is level and stable to avoid any hazardous conditions.

Ensure rack and working platforms are well earthed.

Desk Mounting

1. Attach four rubber pads to the bottom.

2. Place the chassis on a desk.

Mounting the Switch

RESET

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423

Green=1000M Yellow=10/100M On=Link Flashing=ACT

RESET

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 15

Green=1000M Yellow=10/100M On=Link Flashing=ACT

3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251

SFP+

S3910-48TS

20 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251

SFP+

S3910-48TS

Rack Mounting

1. Secure the mounting brackets to the two sides of the switch with eight M4 screws.

2. Attach the switch to the rack using four M6 screws and cage nuts.

RESET

CONSOLE

STATUS PWR1 PWR2 ID

21 43 65 87 109 1211 1413 1615 1817 2019 21

Green=1000M Yellow=10/100M On=Link Flashing=ACT

S3910-48TS

2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251

SFP+

S3910-48TS

1. Attach the mounting brackets to the switch with the supplied screws.

Wall Mounting

2. Use the expansion screws to securely attach the mounting brackets on the wall.

NOTE: Suitable for mounting on concrete or other non-combustible surface only.

S3910-48TS

PWR1

PWR2

Installing the Power Supply Module

1. Take a new power module out of the package.

2. Take the plane printed with power information as the top panel of the power module. Hold the

handle of the power module with one hand, and hold the end of the power module with the other

hand. Insert it into the chassis along the guide rail steadily and slowly until a click is heard, and make

sure that it is in good contact with the power slot.

NOTE: Insert the power module steadily. Please pay attention to the direction of the power

panel to avoid wrong insertion. If the position is not proper, press the plug of the power

module and hold on to the module handle with one hand to pull it out slowly, then

re-insert it.

345678910 11 12

13 14

15 16 17 18 19 20 21 22 23 24

en=10

1G On=Lin

ACT

310-

n=1

/1G

ow=10/100M

n=L

ashi

Reset

PWR1

PWR2

WARNING: Do not install power cable while the power is on.

1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the

switch is mounted.

2. Secure the grounding lug to the grounding point on the switch back panel with the washers and

screws.

Grounding the Switch

1. Plug the AC power cord into the power port on the back of the switch.

2. Connect the other end of the power cord to an AC power source.

Connecting the Power

Other manuals for S3910 Series

This manual suits for next models

Table of contents

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual