Frico Cat User manual

3 kW

CAT

.... 19

.... 11

.... 9

.... 7

.... 5

.... 17

.... 15

.... 13

Original instructions

Fig. 1

Minimum distance in a permanent assembly

10°

[mm]

C3 335 255 276

C5 335 255 276

C9 405 315 335

min 1,8 m

min

300 mm

min 30

0 mm

104104

Ø7

C3 - C5

127127

Ø7

121

C3 - C5 C9

295 170

400

295295

Ø6.5

200

135

165

195

160

195

Fig 2. Mixing cabinet (accessory)

CAT

CBTTK10ST10S EV300

CBT

CMB35 + Cat

Ty p E-nr

(SE)

RSK-nr

(SE)

EL-nr

(NO)

NRF-nr

(NO)

HxBxD

[mm]

T10S 85 809 33 672 84 99 54 911 12 85 024 49 80x80x31

TK10S 85 809 34 672 85 00 54 911 13 85 024 51 80x80x31

EV300 87 513 93 54 910 57 100x80x90

CBT 87 511 87 54 312 02 85 021 79 155x87x43

CMB35 87 112 20 49 306 10 400x295x170

TP3/5 49 306 90

TP9 49 306 10

Accessories

CAT

Technical data

Type E-nr (SE) EL-nr (NO) Output

steps

[kW]

Airﬂow

[m³/h]

Sound

level*1

[dB(A)]

∆t*2

[°C]

Voltage

[V]

Amperage

[A]

HxWxD

[mm]

Weight

[kg]

C3 87 111 03 49 306 13 0/1.5/3 280 41 32 230V~/400V3N~*313.2/4.4 255x335x276 6.3

C5 87 111 05 49 306 15 0/2.5/5 480 40 31 400V3N~ 7. 3 255x335x276 6.7

C9 87 111 09 49 306 19 0/4.5/9 720 44 37 400V3N~ 13.1 315x405x335 10.2

*1) Conditions: Distance to the unit: 3 metres. Directional factor: 2. Equivalent absorption area: 200 m2.

*2) ∆t = temperature rise of passing air at maximum heat output.

*3) C3 can be connected for 230V~ and 400V3N~. Other models should not be connected for single phase, 230V~.

Protection class Cat: (IP44), splash-proof design.

CE compliant.

°C

NLLL

123

654321789

°C

230V3~/400V3N~

400V3N~

230V3~

230V~

LLL

123

3kW

657

CAT 3 / 5 / 9 kW 230V3~/400V 3N~

CBT EV300

LLL

123

44 27

A/B

>t°C

Sensor

Sen-

sor

T10S/TK10S

CAT

°C

CAT

General Instructions

Read these instructions carefully before

installation and use. Keep this manual for

future reference.

The product may only be used as set out in

the assembly and operating instructions. The

guarantee is only valid if the product is used

in the manner intended and in accordance

with the instructions.

Application area

Cat is a range of compact and quiet fan

heaters for stationary use. It is ideally suited

for small stockrooms, in a garage, workshop

or shop.

The mixing cabinet (accessory) allows heating

and ventilation to be combined, through

mixing the return air and outdoor air.

Protection class: IP44

Electrical Installation

The installation should be permanent

and carried out by a qualiﬁed technician

according to applicable directives. The

installation should be preceded by a fully

isolating switch with at least a 3 mm gap and

preferably ﬁtted with a status lamp.

The Cat fan heater is intended for permanent

installation. The knockouts at the rear of the

unit are used to connect accessories. C3 can

also be connected to single phase (230V~).

On the back of the appliance there are knock-

outs. Cable-glands used must guarantee the

protection class requirements!

The heaters can be connected for either

230V3~ and 400V3N~. Note! Other

models cannot be connected for single phase.

Start-up (E)

When the unit is used for the ﬁrst time or

after a long period of disuse, smoke or odour

may result from dust or dirt that has collected

on the element. This is completely normal

and disappears after a short time.

Assembly

The Cat fan heater is mounted on a wall and

has a ﬁxed tilt angle, 10° downwards, which

gives balanced and good heat distribution

• Note that the minimum distances as sat out

in the ﬁgure on page 2 must be maintained.

• The unit must be installed with the

connection area to the left, as seen from the

front.

• Mark out and drill the holes for the screws

as set out in the diagram on page 2.

• Screw in the screws for the keyholes so that

approximately 10 mm remains.

• Hang-up the unit and tighten the screws.

• Screw in the last screw.

Installation with mixing cabinet

Mixing cabinet CMB35 ﬁts C3 and C5. The

mixing cabinet is available as an accessory

and consists of an outer wall grille, a walling-

in frame and a hand controller. The walling-

in frame and outer wall grille are built or

screwed to the wall. The mixing cabinet and

the unit are then ﬁtted. See diagram 2. The

control lever consists of a ﬁxture arm, a wall

ﬁxture, a ball and two adherent joints. A pull-

rod is used between the joints (not included).

Function

Position of the output selector, see

Technical data.

Toggle switch in position °C means

the thermostat only controls the output,

the fan runs continuously.

In position °C the fan is controlled by

a special thermostat, which only switches

on the fan when the heat is on.

It is possible that the temperature limiter

may have tripped during transport, if the unit

does not function the ﬁrst time it’s switched

on. Rectify as set out in the description under

“Overheating”. (Fig. 1)

Assembly and operating instructions

CAT

Overheating

If the unit overheats the integrated

temperature limiter will trip. Reset the

temperature limiter after the unit has cooled

and the fault rectiﬁed. (Fig. 1)

NOTE! All work inside the unit’s connection

area should be carried out by an authorized

technical and the unit must be dead.

The temperature limiter is reset by

removing the cover and pressing the button

on the temperature limiter. (Fig. 1)

Care

The heater fans do not normally need any

maintenance Nevertheless, dirt and dust can

cause overheating and represent a ﬁre risk.

Accordingly, the unit should be cleaned

regularly.

Residual current circuit breaker (E)

When the installation is protected by

means of a residual current circuit breaker,

which trips when the appliance is connected,

this may be due to moisture in the heating

element. When an appliance containing a

heater element has not been used for a long

period or stored in a damp environment,

moisture can enter the element.

This should not be seen as a fault, but is

simply rectiﬁed by connecting the appliance

to the mains supply via a socket without a

safety cut-out, so that the moisture can be

eliminated from the element. The drying

time can vary from a few hours to a few days.

As a preventive measure, the unit should

occasionally be run for a short time when it is

not being used for extended periods of time.

Safety

• For all installations of electrically heated

products should a residual current circuit

breaker 300 mA for ﬁre protection be used.

• The unit has hot surfaces when running!

• The unit must not be positioned so that

inﬂammable material can ignite!

• The unit must not be covered fully or

partially with clothes or similar material,

as overheating can result in a ﬁre risk!

• The unit must not be placed directly under

ﬁxed wall sockets!

• This appliance is not intended for use by

persons (including children) with reduced

physical or mental capabilities, or lack

of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by

a person responsible for their safety.

Children should be supervised to ensure

that they do not play with the appliance.

Art.nr: 201233 2014-04-03 HH/AC/SÅ/SÄ

Main ofﬁce

Frico AB Tel: +46 31 336 86 00

Box 102 Fax: +46 31 26 28 25

SE-433 22 Partille [email protected]

Sweden www.frico.se

For latest updated information and information

about your local contact: www.frico.se

Other Frico Heater manuals

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide