Forno CF01666 User manual

CF01666

CF01672

VOICE ACTIVATED

CEILING FAN

INSTRUCTION MANUAL

Table of Contents

Exclusive Features 1

Before You Begin 2

Parts List 3

Exploded View 4

Important Safeguards and Warnings 5

Installation Preparation

(Down Rod Installation and Flush Mount) 6

Installing Mounting Bracket 6

Down Rod Installation 7

- Securing Fan to Bracket 7

- Electrical Installation with Down Rod 8

- Replacing the Canopy 8

Flush Mount Installation 9

- Electrical Installation for Flush Mount 9

- Flush Mount Installation 9

- Securing Fan to Bracket, Flush Mount 10

Installing the Blades for Down Rod

and Flush Mount 11

Installing the Light 11

Getting to Know Your Remote Control 12

Checking Your Installation 12

Installing the Voice Command Centre (VCC) 13

VCC Voice Instructions and Actions 13

Voice Commands 14

Before You Begin Setting Up the App 14

Setting Up the App 15

Sharing the App 15

Communication Device Cautions 16

Antennae and Other Communications

Information 16

Trouble Shooting 17

Performance and Energy Information 18

Warranty 19

Customer Care 20

Thank you for purchasing our FORNO VOCE ceiling

fan that comes packed with exclusive features:

1. Bluetooth Voce system. Take full control of your

ceiling fan using just your voice. No need to use

any other device like your phone, remote nor any

other communication assistant.

2. You have the flexibility to control multiple fans

that are in the same area using your voice. Or,

control them independently if you want.

3. Bluetooth Voce app that allows you to securely

connect your phone and control your fan with

a tap.

4. You can also control multiple fans in different

rooms.

5. It has a Smart Scheduler that allows you to freely

set when you want the fan and light to be

switched on and off, fan speed, light intensity,

weekend, weekday, etc.

6. 3 pre-set fan programs:

a. Breeze, that gives you a soothing, sequentially

changing breeze speed.

b. Wind, gives you an invigorating, randomly

changing wind speed.

c. Eco, will even out your room temperature

giving you a more comfortable and energy

efficient environment.

7. Super Efficient, Silent and Reliable Brushless DC

motor.

8. Fully dimmable LED lights.

9. Includes a handheld remote control for easy fan

speed and lighting adjustment.

10. 6 fan speeds in your remote control, but 20

speeds when you use your App for the ultimate

comfort.

11. Pre-wired remote receiver, making for an easy

and faster ceiling fan installation.

12. Unique ceiling fan blade design that minimizes

air noise.

BEFORE YOU BEGIN

READ CAREFULLY AND SAVE THESE INSTRUCTIONS

!WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

• Use this unit only in the manner intended by the manufacturer. If you have question, contact the

manufacturer.

• Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means

to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

• To Reduce The Risk Of Personal Injury, Do Not Bend The Blade Brackets When Installing The Brackets,

Balancing The Blades, Or Cleaning The Fan. Do Not Insert Foreign Objects In Between Rotating Fan Blades.

• To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box Marked Acceptable For

Fan Support And Use Mounting Screws Provided With The Outlet Box.

• To Reduce The Risk Of Electric Shock, Disconnect The Electrical Supply Circuit To The Fan Before Installing

Light Kit.

• CAUTION To reduce the risk of injury to people, the fan must be mounted at least 7 ft. (2.1 m) clear distance

from the blades to the floor and 30”(0.76 m) clear from any wall or object.

• CAUTION When mounted directly to the building structure, appliance installation shall not expose

combustible material and do not install the appliance to a ceiling with combustible finish. The installation of

the appliance cannot leave the wood of the rafters or any thermal insulation exposed to the interior of the

room.

• CAUTION All set screws must be checked, and retightened where necessary, before installation.

• All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical

installation should be performed or approved by a qualified licensed electrician.

• Switches must be UL/CSA General Use Switches. No dimmers, electronic switches or rheostats should be

used with this fan.

• After making electrical connections, spliced conductors should be turned upward and pushed carefully up

into outlet box. The wires should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box.

• Electrical diagrams are for reference only. On installation, comply with all your local electrical codes.

• Do not operate the Eco Mode while the fan blades are still in regular motion. You must turn the fan off and

wait for the blades to stop before you engage Eco mode as this will reverse the movement of the blades.

• To avoid personal injury or damage to the fan and other items, use caution when working around or

cleaning the fan. Do not place any object in the path of the blades.

This fan may be installed with a Down Rod or Flush Mount

Please open your box very carefully and take out all the components.

Part # Items Drawing Description Quantity

SCF01666REC

SCF01672REC Remote Control Receiver 1

SCFROD06-TT,

OR, AG

SCFCLIP

SCFPIN

Down Rod (6) with

Clip (6A) and

Pin (6B)

3SCF002CON

Pack with 3 Wire Connectors,

2 Metallic Washers and

4 Spring Washers

SVCCI Voice Control Centre (VCC I) 1

13SCFREM Remote Control and Holder 1

Parts List

SCF002BRA

SCF002SCR-CH, BL, BB

Mounting Bracket (1) with

4 Screws (2) 1

7SCF002YOK-TT, OR, AG Yoke Cover 1

8SCF002MOT-TT, OR, AG Motor Assembly 1

5SCF002CAN-TT, OR, AG Canopy 1

12SCF002SHA Lamp Shade 1

11SCF002LMP-TT, OR, AG Lamp Base 1

SCF01666BLA-B, L

SCF01672BLA-B Curved Propeller Blades 3

9SCF002 Pack of 7 Blade Screws, Spring

Washer and Washers 1

Tools Required

If you find any part missing

please call: 1-866-231-8893

Or contact us at:

mysupport@fornoworld.com

Please do not return this fan

to the store before calling

Stop Ladder

Philips Screw

Driver

Pliers

Wire Stripper

Measuring Tape

Electrical Tape

Exploded View

CF01666-XXX - Net Weight: 6.7kg (14.74 lbs)

CF01672-XXX - Net Weight: 6.9kg (15.18 lbs)

CF01666-XXX is Suitable For Use in Dry Indoor Locations

CF01672-XXX is Suitable For User in Dry Indoor Locations

You should have received all the parts in the Parts List.

WARNING: To avoid risk of electrical shock,

before attempting installation turn off the

electricity at the main electrical box or fuse box.

! WARNING: Any electrical installation should

be done or approved by licensed electrician.

! WARNING: To avoid risk of electrical shock,

this fan should not be installed with any dimmer

or other control device.

! WARNING: To avoid risk of personal injury,

do not insert or place any object in the path of the

blades.

! WARNING: To avoid risk of personal injury,

do not bend the brackets or the blades during

installation, cleaning, etc.

! WARNING: To reduce the risk of fire, electric

shock or personal injury, mount the fan directly on

to a structural framing member or on an electric

box marked Acceptable for Fan Support of

15.9 kg (35 lbs) or less and use the mounting

screws supplied with the electric box. You can also

support it directly to the building structure. Most

electrical outlet boxes commonly used for lighting

fixtures are not acceptable for Fan Support and

may need to be replaced. If in doubt, consult a

qualified electrician.

Installing Mounting Bracket

Installation Preparation

In your panel, turn OFF the

switches or fuses that feed

electricity to the electric box you

will be using to install your fan.

Also turn off the wall switch that

feeds that box.

This fan can be mounted with the Down Rod (6) in

a flat ceiling or a vaulted ceiling as long as the

angle of the ceiling is under 19 degrees.

This unit can also be mounted

flush on the ceiling.

The fan must be mounted with a minimum of 7 ft.

(2.1 m) clear distance from the blades to the floor

and 30” (0.76 m) clear from any wall or object.

Important:

Partially loosen the screws in the

slotted holes of the Canopy.

Remove the other 2 screws from

the Canopy/Bracket assembly.

Twist and separate the Canopy

from the Mounting Bracket. Save

the screws.

Make sure that your

box is properly

grounded and has

either a green or a

bare wire.

! WARNING: The electrical outlet box

should be clearly marked“Suitable for

Fan Support”. Failure to do this may

result in serious personal injury.

OFF

30”

0.76 m

7’

2.1 m

Pass the wires in the electrical box through

the centre of the Mounting Bracket. Install

the Mounting Bracket onto the electrical

box using the screws and washers that

came with the box.

Please note to put

the opening of the

bracket towards the

top if installing on a

vaulted ceiling.

! WARNING: Failure to disconnect

power supply to the box may result in

serious injury. Turn off circuit breakers

or take out fuses now.

Applies to both: Down Rod Installation Flush Mount

If you are doing a Down Rod Installation

Go to page 7

If you are doing a Flush Mount Installation

Go to page 9

Set Screw

and Nut

Set Screw

Clamp

Yoke

Securing Fan to Bracket

5. Insert the Down Rod into

the Yoke making sure that

the wires are not twisted

and aligning the holes for

the pin on the Down Rod

with the holes in the motor

Yoke. Insert Pin all the way

through and put the Clip in

place. Secure tightly the2

Set Screws and Nut. Lower

Yoke cover until it rests on

the Motor Assembly.

3. Loosen the Set Screw

and Nut and the Set

Screw on the Yoke.

Take the Clamp out

from the Safety

Cable.

Down Rod Installation

1. Remove the Clip (6A)

and Pin (6B) from your

Down Rod (6). Save

the Clip and the Pin.

4. Thread the wires and

safety cable that

comes from the Motor

Assembly through the

Down Rod.

2. Insert the Canopy (5)

and the Yoke Cover

(7) following the

drawing on the right.

Put his assembly

aside.

Down Rod

ClipPin

! WARNING: Failure to align

hanging ball slot with hanging bracket

tab may result in serious personal

injury or death.

Canopy

Yoke Cover

Wood Screw

and Washer

Clamp

Safety Cable

Wood Ceiling Joist

Safety Cable Loop

Hanging Bracket Tab

Hanging Ball Slot

Down Rod Installation

Installing the Down Rod

1. Using a step ladder lift the fan and using the

opening in the bracket, insert the hanging ball

part of the Down Rod into the bracket and let it

rest there. Gently turn the Down Rod until

you see and feel that the ball slot engages

firmly with the hanging Bracket tab.

2. Find a secure place (preferably a joist) and

using a wood screw and washer (not supplied)

secure the safety cable to it. Adjust the slack of

the safety cable using the clamp. (This step is

NOT required in the US, you can cut the safety

cable or just coil it around the canopy).

Antenna

White Supply Wire Ground

(green or

bare)

Ground

(green or

bare)

Green Ground

Receiver

White

AC IN N

White

Black

AC IN L

Black Supply Wire

From ReceiverFrom Receiver

From CeilingFrom Ceiling

Male Connectors

from Down Rod

! WARNING: Failure to disconnect

power supply to the box may result in

serious injury. Double check now that

the circuit breakers to the box are off.

Replacing the Canopy

Go to Page 11 to complete your installation

Electrical Installation with Down Rod

Wrap each wire connector with

Electrical Tape for extra safety

Lift canopy to Mounting Bracket and align slotted holes in canopy

with loosened screws in Mounting Bracket. Twist canopy to lock.

Tighten all canopy mounting screws securely. Ensure that wires

have not been compressed by the canopy.

Insert the 3-piece male connector from

the Down Rod to receiver’s 3-piece

female connector. Make sure the Red

wire aligns with the Red wire, the

Brown with the Brown and the Yellow

with the Yellow. Then insert the 2-piece

male connector from the Down Rod to

receiver’s 2-piece female connector

aligning White with White and Black

with Black.

Using the wire connectors:

1. Connect the L (Black) wire from your

Receiver to the Live (Black) wire from

your ceiling electric box.

2. Connect the N (White) wire from your

receiver to the Neutral (White) wire

from your ceiling electric box.

3. Connect the green Ground wire that

comes from the Ball of the Down Rod

to the Green wire that comes from

your receiver, the green wire from

your bracket and to the green wire (if

there is one) that comes from your

box and at the same time to the bare

or green wire that comes from your

electric supply wire bundle.

Gently insert the receiver into the Mounting Bracket with the flat part

towards the top. Carefully push wires and wire connectors into the

electric box leaving the antenna outside of the Mounting Bracket.

Spliced conductors should be turned upward and pushed carefully up

into outlet box. The wires should be spread apart with the grounded

conductor and the equipment-grounding conductor on one side of the

outlet box.

Using the wire connectors:

1. Connect the L (Black) wire from your Receiver to

the Live (Black) wire from your ceiling electric

box.

2. Connect the N (White) wire from your receiver

to the Neutral (White) wire from your ceiling

electric box.

3. Connect the green Ground wire that comes

from the receiver to the green wire that comes

from your Bracket, also to the green wire (if

there is one) that comes from your box and at

the same time to the bare or green wire that

comes from your electric supply wire bundle.

Remove 3 opposing screws from the Yoke in the

top side of the Motor Assembly. Save the screws.

Thread the wires from the Motor Assembly through

the centre of the canopy.

Place the Canopy so that the 3 large holes in the

Canopy align with the 3 heads of the screws you

left on the Yoke.

The 3 small holes should align with the threads in

the Yoke. Replace the 3 screws you took out in

those holes and tighten.

White Supply Wire Ground

(green or

bare)

Ground

(green or

bare)

Green Ground

Receiver

White

AC IN N

White

Black

AC IN L

Black Supply Wire

From ReceiverFrom Receiver

From CeilingFrom Ceiling

! WARNING: Failure to disconnect

power supply to the box may result in

serious injury. Double check now that

the circuit breakers to the box are off.

Flush Mount Installation

Flush Mount

Flush Mount Installation

Electrical Installation for Flush Mount

Wrap each wire connector with

Electrical Tape for extra safety

This manual suits for next models

Table of contents

Other Forno Fan manuals

Forno

Forno VOCE CF02118 User manual

Forno

Forno Voce CF01566 User manual

Forno

Forno VOCE CF00200 Series User manual

Forno

Forno VOCE CF01360 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual