Follett Ice Pro DB650 Setup guide

Installation, Operation and Service Manual

Ice Pro™DB650, EDB650 Automatic

Ice Bagging and Dispensing System

00913509R03

801 Church Lane • Easton, PA 18040, USA

Toll free (877)612-5086 • +1 (610)252-7301

www.follettice.com

Following installation, please forward this manual

to the appropriate operations person.

Order parts online

www.follettice.com

230V 50Hz

models only

220V 60Hz

models only

Contents

Welcome to Follett. . . . . . . . . . . . . . . . . . . . . 3

Before you begin........................... 3

Specications ........................4

Electrical ................................ 4

Plumbing................................. 4

Clearance and access information ............. 4

Ice type ................................. 4

Icemaker weight limit ....................... 4

Environment .............................. 4

Container sizes ............................ 4

Bag pins ................................. 4

Dimensions and clearances .................. 5

Installation ...........................6

Location ................................. 6

Leveling.................................. 6

Utility connections.......................... 6

Bag pin installation ......................... 7

Foot pedal accessory ....................... 7

Bag installation ............................ 7

Adjusting drain pan......................... 9

Brush bracket ............................. 9

Sanitize .................................. 9

Icemaker ................................. 9

Filling other containers ......................10

Operation ...........................11

How the dispenser works ....................11

Control functions.......................... 12

Power switch............................. 12

Cleaning and sanitizing .................... 13

DB650 wiring diagram, upper control box ...... 14

DB650 wiring diagram, lower control box....... 15

EDB650 wiring diagram, upper control box ..... 16

EDB650 wiring diagram, lower control box ..... 17

Before calling for service ................... 18

Replacement parts & accessories ......19

Accessories ............................. 19

Upper chassis............................ 20

Lower chassis............................ 21

Lower chassis (cont.) ...................... 22

Dispense auger .......................... 23

Electrical system, upper box................. 24

Electrical system, lower box ................. 25

Welcome to Follett

Follett ice dispensers enjoy a well-deserved reputation for excellent performance, long-term reliability and

outstanding after-the-sale support. To ensure that this dispenser performs as intended, we ask that you take

a moment to review this manual before beginning the installation of the dispenser. Should you have any

questions or require technical help at any point, please call our technical service group, (877) 612-5086 or

+1(610) 252-7301.

Before you begin

After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If

damage is found, notify the shipper i mmediately and contact Follett Corporation so that we can help in the

ling of a claim, if necessary.

Check your paperwork to determine which model you have. Follett model numbers are designed to provide

information about the type and capacity of Follett ice dispensing equipment. Following is an explanation of the

different model numbers in the Ice Pro series.

DB650SA

Important cautions

Storage area of dispenser contains mechanical, moving parts. Keep hands and arms clear of

this area at all times. If access to this area is required, power to unit must be disconnected rst.

Ice is slippery. Maintain counters and oors around dispenser in a clean and ice-free condition.

Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.

Should local codes require a hard-wired connection and/or shielded wiring, eliminate the cord(s)

and plug(s) and follow the appropriate wiring diagram.

Dispenser can accommodate most cube or cubelet ice up to 1" (25.4 mm) square as well as

Horizon Chewblet®ice. Crushed, ake, or nugget ice cannot be used. Use of these ice types can

jam dispenser and will void warranty. For questions about ice compatibility, call Follett’s

customer service group toll free at (877) 612-5086 or +1 (610) 252-7301.

Always disconnect power before cleaning or servicing the dispenser.

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised

or provided instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

SA = Semi-Automatic ice dispensing and bagging

650 – 650 lbs maximum bin capacity

DB – Dispensing bin - 220/60 Hz

EDB – Dispensing bin - 230/50 Hz

Specications

Electrical

DB650 – The Ice Pro DB650 dispenser requires a separate electrical circuit from the icemaker. Equipment

ground required. Standard electrical - 220V, 60Hz, 1 phase, maximum fuse – 5 amps, 15 amp circuit, NEMA

6-15 receptacle. The cord length is approximately 7' (2.1 m) from right rear. A plug is provided.

EDB650 – The Ice Pro DB650 dispenser requires a separate electrical circuit from the icemaker.

Equipment ground required. Standard electrical - 230V, 50Hz, 1 phase, maximum fuse – 5 amps, 15 amp circuit,

max power - 3450 watts. The cord length is approximately 7' (2.1 m) from right rear. A plug is not provided.

Plumbing

Drain 1" PVC FPT for bin drain – run to oor drain.

Note: Drains should be hard-piped and insulated. Maintain at least 1/4" per foot (1 cm per 48 cm run) slope

on drain line run. Do not tee into icemaker drain line.

Clearance and access information

Door entry

– Installation sites must have an unobstructed path to installation location with door openings no

less than 34.5" (877 mm).

Service clearance

– A minimum of 12" (305 mm) to right of unit is necessary for service.

Ice type

Dispenser can accommodate most cube/cubelet ice up to 1" square as well as Follett Horizon™ Chewblet ice.

Crushed, ake, or other manufacturers nugget ice cannot be used. Use of these ice types can jam dispenser

and will void warranty. For questions about ice compatibility, call Follett’s technical service group toll free at

(877) 612-5086 or +1(610) 252-7301.

Icemaker weight limit

Icemaker mounted directly on top of bin must not exceed 800 lbs (363 kg).

Environment

Intended for indoor use only - operating temperature range of 40 - 100 F (4 – 38 C). Not suitable for installation

in an area where a water jet could be used. (The dispenser should not be cleaned with a water jet or be

exposed to water jet used to clean surrounding areas.) The dispenser has to be placed in a horizontal position.

The dispenser is only to be installed in locations where it can be overseen by trained personnel.

Container sizes

Unit accommodates bag sizes up to 20 lbs (9 kg) / 27.35" (695 mm) high.

Dispense chute compatible with carts and containers up to 28" (712 mm) high.

Bag pins

Bag pins may be adjusted to accommodate bag hole centers from 5" (127 mm) to 10" (254 mm).

Notes

Follett Horizon icemakers and other icemakers less than 30" wide require a top that adds 2" to standard

unit height.

12" (305 mm)

Service

Clearance

19.88"

(505 mm)

1" FPT drain

28"

(712 mm)

max. cart

26"

(661 mm)

max. bag

8.63"

(220 mm)

1" FPT drain

34.25"

(870 mm)

(1651 mm)

48.25

(1226 mm)

30.75

(782 mm)

33.75

(858 mm)

29.75

(756 mm)

Side view

Front view

Dimensions and clearances

Installation

Location

A minimum of 12" (305 mm) to the right of the unit must be available

for service clearance (see dimensions and clearances - page 5).

Allow access to front of unit for bagging operation and dispensing.

Leveling

Leveling the unit is important for the proper operation of any

top mounted icemaker. The dispenser is shipped with the legs in the

fully retracted position. Each leg may be adjusted independently by

turning clockwise to lower the leg or counterclockwise to raise the

leg. Do not remove legs; interference will occur with the bag stand

and dispense chute.

Utility connections

Bin drain

Drain connection is made to the 1" FPT PVC tting (Fig. 1). Allow a

minimum of 1/4" per foot (1 cm per 46 cm run) slope on drain line run.

Insulate the entire run length to prevent condensation from forming on

outside of drain line.

Note: Avoid excessive tightening force when connecting to this tting.

Note: Do not apply excessive heat if any sweating of ttings is

necessary. Heat conduction through metal may melt threads in

plasticdrain.

Drain pan

The drain pan on the bag stand may be drilled out and plumbed

if desired. Use an 11/16" drill bit, a 3/4" FPT elbow and PVC glue.

Plumb with exible tubing to allow for height adjustment.

Electrical

Electrical connections to be in accordance with local and national

electrical codes. Each dispenser and icemaker require separate

circuits. Equipment ground required.

Note: If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualied persons in order to

avoid a safety hazard.

DB650

220V, 60Hz, 1 phase. Max. fuse – 5 amps, 15 amp circuit.

Provide NEMA 6-15 receptacle within 7' (2.1 m) of right rear corner.

Cord and plug provided.

EDB650

230V, 50Hz, 1 phase. Max. fuse – 5 amps, 15 amp circuit, max

power - 3450 watts. Provide means of connection within 7' (2.1 m) of

right rear corner. Cord provided without plug.

8.25"

(210 mm)

13.5"

(343 mm)

drain

Fig. 1 Bottom view

Bag pin installation

1. Position plastic bag pin nuts onto the rear slots of the bag stand

(Fig. 2).

2. Thread in and tighten bag pins.

Fig. 3

Fig. 2

Fig. 4

Foot pedal accessory

The optional foot pedal accessory allows dispensing of ice while

keeping your hands free. The pedal is placed on oor near bag

stand in front of the dispenser. It plugs into the 3-pin connector

located just under the control panel behind the blower motor

(Fig.3).

Bag installation

Note: Bag pins are designed to be used with bags mounted on wire

wickets. Do not install more than one wicket of bags at a time.

1. Move chute lever to up position (Fig. 4).

2. Adjust bag pin width to match that of the bag wicket

(Fig. 5). Center bag pins evenly.

Fig. 5

Fig. 6

Fig. 7

3. Remove rubber keepers from wicket and insert wicket wires

into bag pins. Transfer bags from wicket to bag pins. Slide 15

to 20 bags onto pins at a time until pins are full (Fig. 6).

4. Return chute lever to down position (Fig. 7). The

back of the chute holds bags to prevent more

than one opening at a time.

Adjusting drain pan

The drain pan may be raised or lowered to accommodate different

bag sizes and helps to support the bag while lling (Fig. 8). The

bottom of bags should rest on the tray when adjustment is correct.

1. Lift drain pan up and out of receiving slot on bag

stand base.

2. Insert drain pan in and down into desired receiving

slot on bag stand.

3. Marking the drain pan position makes future positioning easier.

Brush bracket

Mount the cleaning brush bracket to the top front left or right side

of the bin in one of the threaded inserts and hang cleaning brush

(Fig. 9).

Sanitize

Follow cleaning and sanitizing instructions before use - see

page13.

5.0"

(127 mm) 4.5"

(114 mm)

6.0"

(152 mm)

Fig. 8

Fig. 9

Fig. 10

Icemaker

Follow icemaker manufacturer’s recommendations for installation.

Note: Icemaker mounted on top may not exceed 800 lbs (363kg).

Ensure that the drop zone of the ice does not fall onto the upper

right hand section of the bin (See shaded area in Fig. 10). Ice

falling from ice machine can hit this area of the bin and cause

damage to the icemaker.

Fig. 11

Fig. 12

Filling other containers

1. Ensure blower is off.

2. Move chute lever to up position (Fig. 11).

3. Adjust drain pan as needed.

4. Containers up to 28.75" (731 mm) tall may be

used by removing drip tray (Fig. 12).

Other manuals for Ice Pro DB650

This manual suits for next models

Table of contents

Other Follett Ice Maker manuals

Follett

Follett Horizon Elite HMF1010RJS User manual

Follett

Follett Horizon HCD1000RHT User manual

Follett

Follett Horizon Elite 2110 Series User manual

Follett

Follett Horizon Elite 1400 Series Operation manual

Follett

Follett E7CI100A Setup guide

Follett

Follett HMD1000N Operation manual

Follett

Follett Horizon HCD1000RVS User manual

Follett

Follett Horizon Elite HC Series Operation manual

Follett

Follett Horizon HCC1000ABT User manual

Follett

Follett Maestro User manual

Follett

Follett Horizon Elite Chewblet 1010 Series User manual

Follett

Follett Horizon Elite 710 Series User manual

Follett

Follett E-ITS100-31 User manual

Follett

Follett HCC1010A Operation manual

Follett

Follett HCE Operation manual

Follett

Follett Horizon Chewblet series User manual

Follett

Follett MCD425A Setup guide

Follett

Follett Horizon Elite series User manual

Follett

Follett HCE/HME700A Manual

Follett

Follett U300 Series User manual

Follett

Follett Horizon Elite 1010 Series User manual

Follett

Follett HCE1400A Operation manual

Follett

Follett HCD1650RBT User manual

Follett

Follett HCE1000A Operation manual

Popular Ice Maker manuals by other brands

Hoshizaki

Hoshizaki KMD-460MWJ instruction manual

Sub-Zero

Sub-Zero 315I Planning information

Unold

Unold 48945 Instructions for use

Kenmore

Kenmore 2217402A Use & care guide

Cornelius

Cornelius WM600 Installation & owner's manual

GE XPIO43SCSS owner's manual

Hoshizaki

Hoshizaki KMD-901MAH Specifications

Whynter

Whynter FIM-450HA instruction manual

U-Line

U-Line UMCR014-SC01A User guide & service manual

Andrew James

Andrew James AJ000522 manual

Scotsman

Scotsman CME1356 user guide

Scotsman

Scotsman ACM 25 Service manual

Kärcher

Kärcher IP 120 manual

U-Line

U-Line SS1095 Quick referenc guide

Maytag

Maytag MIM1554WRS - Ice Maker User instructions

Hoshizaki

Hoshizaki KM-630MAH instruction manual

Princess

Princess Yonanas user manual

Unold

Unold 48946 Instructions for use