Foldawheel Draco User manual
V2.0
User Manual
Draco
TABLE OF CONTENT
PARTS INTRODUCTION
01
Title Page
Parts Introduction 01
1.0 Safety Tips 02 - 03
2.0 Set Up Upon Arrival 04
3.0 Adjustments 05 - 07
4.0 Operation 08 - 09
5.0 Control System 10 -14
6.0 Maintenance 15
Contact Us 15
01. Headrest
02. Backrest
03. Armrest
04. Side Panel
05. Recline Actuator
06. Motor/Differential Gear
07. Anti-Tipper Wheel
08. Rear Wheel
09. H-belt
10. Joystick
11. Seat Cushion
12. Knee Belt
13. Calves Cushion
14. Footrest
15. Swing Castor
16. Front wheel
01
02
03
04
05
06
07
08
15
16
10
13
12
14
09
11
02
1.0 SAFETY TIPS
1-1.1. Standing up stresses your body in ways you may not be used to. Therefore we
recommend you consult your doctor or physical therapist before using the
stand-up wheelchair.
1-1.2. Before using the standing wheelchair, it is absolutely vital that the
knee support, safety belt and chest belt are xed correctly.
Switch on the master power switch before using. (see P9)
- Before using the standing wheelchair, you should be familiar with the operation
and the function.
- Use only on standard household, hard and even ground. Not to be used on wet
surface.
- In case of staircase, the standing wheelchair must be carried by 4 persons.
- When getting on or off the stand up wheelchair, do not put the foot on the
footplate, to avoid danger.
1-1. Standing
Attention :
Warning: Maximum weight should not exceed. 250 lb.（120 kg）
DO NOT DRIVE OVER UNEVEN GROUND!
Danger of tipping over!
DO NOT LEAN OUT OF THE RAISED VERTICALIZER!
Danger of tipping over!
NEVER DRIVE ON ASCENDING OR DOWNWARD SLOPES
WHEN THE VERTICALIZER IS RAISED!
Danger of tipping over!
NEVER REACH INTO THE MOVING APPARATUS OF THE
RAISED VERTICALIZER!
Danger of crushing!
1-2. Important point to note for operating the wheelchair
The following actions should not be attempted:
03
* Only ever drive downhill at a maximum of 1/5 of the top speed! Avoid abrupt
braking or acceleration on gradients.
* If at all possible, avoid driving on slippery surface (such as gravel) where there is a
danger of you losing control over the wheelchair, especially on a gradient! If driving
on such a surface is inevitable, then always drive slower and with the utmost caution.
* Never attempt to overcome an obstacle when on an uphill or downhill gradient!
* Never attempt to drive up or down a ight of steps with your wheelchair!
* Always approach straight on! Ensure that the front wheels and rear wheels move
over the obstacle in one stroke! Do not stop halfway! Do not exceed the maximum
obstacle height!
* Avoid shifting your center of gravity, or abrupt joystick movements and
changing of direction when the wheelchair is in motion!
* Never use the wheelchair to transport more than one person!
* Note that the wheelchair will brake or accelerate if you change the Driving Mode
whilst the wheelchair is in motion!
Always practice with your Healthcare professional or attendant. Before attempting
to negotiate curbs, inclines or ramps alone., it is important for you to develop a safe
technique that is suitable to your abilities.
1-3. Safety Information on Driving and Free wheel Mode
1-4. Rear Wheels
Danger of injury if the wheelchair tips over
Curbs, inclines and ramps
Never lift the wheelchair by the ip-back armrests. These parts are detachable and
lifting the wheelchair by them may cause damage to the chair or injury to the user.
1-5. Armrests
Flip-back armrests
Power stand up wheelchair does not advocate the use of power drive attachments on
any power wheelchair. Use of a power drive attachment on wheelchair alters its
intended use. Installation of a power drive attachments is considered an alteration to
the frame and voids the warranty.
1-6. Power Drive Attachments
Marketing any unauthorized modications or using parts not supplied by
technical personnel may change the whelchair structure and create an unsafe
condition, thus voiding the warranty.
1-7. Modifications
Doing a “wheelie”(tilting the wheelchair backward to its balance point) can be dangerous.
Do not attempt this maneuver without an attendant.
Warning :
1.0 SAFETY TIPS
~ Power stand up wheelchair, joystick, heel strap & chest belt
~ Knee support & headrest
~ Charger
~ User manual, oil pot and tool
~ Options as ordered
Remove any transport straps or transport guards.
2-1. The Original Package And Accessories
2-2. Unfolding The Stand Up Wheelchair
The Original Package And Accessories Contain The Following Components :
~ Lay down the backrest and tighten the knobs on the left and right.(P1,P2)
~ Swing the backrest and armrest forward, lift the side panel up.(P3)
~ Tighten (not too tight) the screw for pull rod of the armrest.(P4)
~ Tighten (not too tight) the screw of the actuator.(P5)
~ Assemble the headrest.(P6)
Backrest Assembly Instructions :
2.0 SET UP UPON ARRIVALS
P5 P6
04
Set-up Video QR Code
3.0 ADJUSTMENTS
Should you require adjustments and alterations to the mechanism of the wheelchair,
or any maintenance work, please contact qualified technicians.
- Use the controller to raise the seat a little bit.（P7）
- There are 4 screws on both side that need to be remove in order to adjust the
seat depth. Remove the bottom 2 screws on both side, then pull the inner tube
out to extend the seat depth（P7~8）. Put back the screws when you get your
desire seat depth.
- Remove the top 2 screws and repeat the steps, make sure the length of top and
bottom is the same.（P10）
Theheightofthefootrestisadjustableandshouldbealteredinlinewithyour
bodyproportionstoguaranteethebeststandingpositionpossible.Footrest
adjustmentshouldalsotakeintoaccountyourchoiceofseatcushion.（P10~11）
- Aftertakingoutthescrews(bothsides),thefootrestheightcanbeadjusted
bysecuringondifferentholes.Eachholesare1.8cmdifference.
- Retightenthescrewsatyourdesireheight.
3-1. Adjusting The Seat Depth
3-2. Adjusting The Footrest Height
P7 P8 P9
P10 P11
05
3-3. Adjusting The Footrest Angle
3.0 ADJUSTMENTS
3-5. Chest Belt
- By removing the top screw (left and right) , the footrest has 3 adjustable angle
(P12, 13 & 14)
- Retighten the screws once you get desired angle.
P12
P15
P16
P17
P13 P14
-Makesurethatthechestbeltissecuredonthe
backrestʼsvelcrostrap.
-Thechestbeltistoholdtheupperbody(chest)
inplace.
3-4. Knee Support And Belts
3-4-1. Knee Belt
The most important safety features of the stand-up wheelchairs are the knee
support, safety belt and chest belt. It is absolutely essential that these are correctly
in place before you attempt to stand up.
The knee support holds the knees in an extended posture and prevents you from
slipping out from the wheelchair while standing up.
Attach the one of the triangular clasp of the knee belt
onto the side of the frame.
Center the knee belt in front of your knee, pull the
velcro belt until it is sitting firmly in place, then attach
the other clasp onto the frame. Knee belt should be
just below (not right on) the knee cap and not too tight.
06
Low Medium High
P18
P20
P19
P21
3-5-2. Safety Belt
3-5-1. H-Belt
- The safety belt holds the waist in place.(P20)
-Make sure that the safety belt is secured on the the backrest’s velcro .
- Close the catch on the safety belt and pull it but not too tight.(P21)
-To release the safety belt., simply press the red button in the center of the catch.
- The H-belt holds the upper body in place.(P18)
- Close the catch on the belt and pull the strap to tighten. (not too tight)(P19)
-To release the safety belt, press the top and bottom part of the center of the catch.
3.0 ADJUSTMENTS
07
3-6. Adjusting The Armrest
B
A
1
3 4
2
1) Remove A screws and loosen B screws.
2) Adjust the Armrest to the desired height.
3) Secure screws A
4) Tighten screws B
4.0 OPERATION
4-1. Before Driving for the First Time
Make sure :
- Before you take your first trip, you should familiarize yourself with the
operation of the vehicle and with all operating elements. Take your time to
test all functions and driving modes.
- Your electric wheelchair is able to overcome obstacles and curbstones to
a maximum height of 5 cm.
- When driving in standing position, speed is limited to 1/5 of the
maximum speed.
4-3. Driving up and down gradients
Your electric wheelchair has a maximum tilt-resistant climbing ability of
10 degrees.
* You are within easy reach of all operating controls.
* The battery charge is sufficient for the distance intended to be covered.
* The restraining belt is in perfect order.
Warning :
* Never approach obstacles at an angle!
* Put your backrest into an upright position before climbing an obstacle!
* Never drive over obstacles with an erected vertical(standing position).
* Only ever drive obstacles at a maximum of 1/5 of the top speed! Avoid abrupt
braking or acceleration on gradients.
Warning :
* Only ever drive downhill at a maximum of 1/5 of the top speed.
* Avoid sudden changes of direction or abrupt braking when driving on slopes.
* Always return the backrest of your seat to an upright position before ascending
slopes. We recommend that you recline the seat backrest slightly to the rear
before descending slopes.
* If the footrest is raised, drive mode is only used for positioning and not for regular
drive operation. Lower the footrest before ascending a slope.
* Never attempt to ascend or descend a slope on slippery surfaces or where there
is a danger of skidding.
* Avoid trying to get out of the vehicle from an incline or a gradient.
* Always drive straight in the direction of the road or path you are going,
rather than attempting to zigzag.
* Never attempt to turn around on an incline or a slope.
Danger :
* When the seat is raised, drive operation only serves positioning, not driving.
* Never driven over uneven ground on an upward or downward slope obstacles.
08
4.0 OPERATION
4-4. Free Wheel
The motors are designed to engage the electromagnetic brakes
when the vehicle is not in use or when the power is OFF. There is also a
manual feature that allows the unit to “freewheel”. Free-wheeling is
accomplished by pulling the free-wheeling levers to the free-wheeling position.
(P22~23)
Warning :
* Never free-wheel your power wheelchair on a slope.
* Never free-wheel the motors while operating your vehicle.
* Always remember to engage the motors before turning the power back ON.
09
5.0 CONTROL SYSTEM
Master Power Switch
* Switch on the master power before using.
The Dynamic DX2 Remote
Assembly of the remote
1. ON/OFF
2. Left indicator button
3. Function keys I
4. Drive profile selection +
5. Drive profile selection -
6. Horn
7. Joystick
8. Accessory mode selection
9. Accessory mode selection
10. Function keys II
11. Screen
12. Right indicator button
Lower Side
1.Combined charging socket/
programming socket
P22 P23
Popular Mobility Aid manuals by other brands
Rhythm Healthcare
Rhythm Healthcare B3800F manual
AMF-BRUNS
AMF-BRUNS PROTEKTOR installation manual
Drive DeVilbiss Healthcare
Drive DeVilbiss Healthcare OTTER Instructions for use
Rhythm Healthcare
Rhythm Healthcare C500U Assembly and Fitting Instructions
Lumex
Lumex RJ4200A manual
Rebotec
Rebotec Jumbo user manual