FMI Peninsula VDVF36 Quick start guide

For more information, visit www.fmiproducts.com

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference.

DIRECT-VENT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

PENINSULA MODELS (V)DVF36

TPNA-A(-HA)/TPNPA-A/TPNEA-A/TPNPEA-A

SEE-THRU MODELS (V)DVF36

TSTA-A(-HA)/TSTPA-A/TSTEA-A/TSTPEA-A

Peninsula Model

Shown

PFS

USC

www.fmiproducts.com 56131L2

SAFETY

WARNING: Improper

installation, adjustment,

alteration, service or

maintenance can cause

injury or property dam-

age. Refer to this manual

for correct installation

and operational proce-

dures. For assistance or

additional information

consult a qualified in-

staller, service agency or

the gas supplier.

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases, unless

a certied kit is used.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

This direct-vent gas re-

place series is intended

for use with natural or

propane/LP gas only. Do

not attempt to burn any

solid fuels in these appli-

ances.

State of Massachusetts:

The installation must

be made by a licensed

plumber or gas tter in

the Commonwealth of

Massachusetts.

WARNING: This product con-

tains and/or generates chemicals

known to the State of California

to cause cancer or birth defects

or other reproductive harm.

IMPORTANT: Check local codes

before installing this replace.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, op-

erate or service this replace.

Improper use of this replace

can cause serious injury or

death from burns, re, explo-

sion, electrical shock and carbon

monoxide poisoning.

TABLE OF CONTENTS

Safety .................................................................. 2

Dimensions.......................................................... 6

Pre-Installation Preparation................................. 7

General Venting................................................. 10

Requirements for the Commonwealth of

Massachusetts................................................... 12

Venting Installation............................................. 13

Fireplace Installation.......................................... 22

Pilot/Electrode Assembly Adjustment ................ 27

Burner Flame Adjustment.................................. 27

Operating Guidelines and Maintenance ............ 28

Operation........................................................... 30

Specications .................................................... 31

Troubleshooting................................................. 32

Wiring Diagrams................................................ 34

Service Hints ..................................................... 35

Technical Service............................................... 35

Replacement Parts............................................ 35

Parts and Accessories....................................... 36

Warranty ..............................................Back Cover

www.fmiproducts.com

56131L 3

This replace must be installed by a qualied

(certied or licensed) service person. It has

a sealed gas combustion chamber that uses

a millivolt gas control valve with a millivolt

ignition system.

Models (V)DVF36TPNA/TPNPA series are

three-sided direct-vent gas replaces and

models (V)DVF36TSTA/TSTPA are two-sided

direct-vent gas replace replaces with sealed

combustion chambers.

Models (V)DVF36TPNEA/TPNPEA and (V)

DVF36STEA/TSTPEA use a direct spark

ignition with a 24 VAC control module. All

models have HI/LO valve that controls the

ame height. These units can be equipped

with louvers for circulating or with panels for

noncirculating operation.

Fan Kit model DVFFBK are available for these

units as an option. If you are uncertain as to

what gas your unit is equipped for, please

check the rating plate located in the interior

of the appliance opening or consult your local

FMI PRODUCTS, LLC distributor.

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

u, with headaches, dizziness or nausea. If

you have these signs, the replace may not

be working properly. Get fresh air at once!

Have replace serviced. Some people are

more affected by carbon monoxide than oth-

ers. These include pregnant women, people

with heart or lung disease or anemia, those

under the inuence of alcohol and those at

high altitudes.

Natural and Propane/LP Gas: Natural and

propane/LP gas are odorless. An odor-making

agent is added to the gas. The odor helps you

detect a gas leak. However, the odor added to

the gas can fade. Gas may be present even

though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this replace.

WARNING: Any change to

this replace or it’s controls can

be dangerous. Do not modify

this replace under any circum-

stances. Any parts removed for

servicing must be replaced prior

to operating replace.

DANGER: Carbon monoxide

poisoning may lead to death!

Before beginning the installation of replace,

read these instructions through completely.

• This FMI PRODUCTS, LLC replace and

its components are safe when installed

according to this installation manual.

Unless you use FMI PRODUCTS, LLC

components, which have been designed

and tested for the replace system, you

may cause a re hazard.

• The FMI PRODUCTS, LLC warranty will

be voided by and FMI PRODUCTS, LLC

disclaims any responsibility for the follow-

ing actions:

a. Modification of the fireplace, com-

ponents, doors, air inlet system and

damper control.

b. Use of any component part not manu-

factured or approved by FMI PROD-

UCTS, LLC in combination with a FMI

PRODUCTS, LLC replace system.

c) Installation and/or operation in a

manner other than instructed in this

manual.

d) Burning of anything other than the type

of gas approved for use in this gas

appliance.

This appliance, when installed, must be

electrically grounded in accordance with lo-

cal codes, or in the absence of local codes,

with the National Electrical Code, ANSI/

NFPA 70.

The installation must conform to local codes,

or in the absence of local codes, with the

National Fuel Gas Code ANSI Z223.1.

This fireplace complies with the National

Safety Standards and is listed and tested by

PFS Corporation to ANSI Z21.50/CSA 2.22

standard as vented gas replace.

Proper installation is the most important step

in ensuring safe and continuous operation

of the replace. Consult the local building

codes as to the particular requirements

concerned with the installation of all factory

built replaces.

NOTICE: Decorative product not

for use as a heating appliance.

SAFETY

Continued

www.fmiproducts.com 56131L4

WARNING: Do not use a blower insert, heat exchanger insert or

other accessory not approved for use with this replace.

WARNING: This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not convertible for

use with other gases unless a certied kit is used.

WARNING: Do not allow fans to blow directly into the replace.

Avoid any drafts that alter burner ame patterns.

Due to high temperatures, the appliance should be located out of

trafc and away from furniture and draperies.

Do not place clothing or other ammable material on or near the

appliance. Never place any objects on the appliance.

Do not use this replace to cook food or burn paper or other am-

mable material.

This replace reaches high temperatures. Keep children and adults

away from hot surface to avoid burns or clothing ignition. Fireplace

will remain hot for a time after shutdown. Allow surface to cool

before touching.

SAFETY

Continued

Carefully supervise young children when they are in the room with

replace.

Keep area around your replace clear of combustible materials, gaso-

line and other ammable vapor or liquids. Do not run replace where

these are used or stored.

www.fmiproducts.com

56131L 5

SAFETY

Continued

6. Have venting system inspected annu-

ally by a qualified service person. If

needed, have venting system cleaned or

repaired.

7. Do not use any solid fuels (wood, coal,

paper, cardboard, etc.) in this replace.

Use only the gas type indicated on re-

place nameplate.

8. Do not use replace if any part has been

exposed to or under water. Immediately

call a qualied service person to arrange

for replacement of the unit.

Do not operate replace if any log is broken.

10. Do not operate replace with glass door

removed, cracked or broken.

11. Provide adequate clearances around air

openings.

12. Fireplaces with the sufx of -HA have been

designed to operate at altitudes of 4000

feet and above. For horizontal installa-

tions above 2,000 feet, it is recommended

that a 12" extension pipe be added before

starter elbow (see High Altitude Installa-

tion, page 21).

1. For propane/LP replace, do not place

propane/LP supply tank(s) inside any

structure. Locate propane/LP supply

tank(s) outdoors. To prevent performance

problems, do not use propane/LP fuel tank

of less than 100 lbs. capacity.

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do

not use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier's instructions

• if you cannot reach you gas supplier,

call the re department

3. Never install the replace

• in a recreational vehicle

• in windy or drafty areas where curtains

or other combustible (ammable) objects

can make contact with the replace front

• in high trafc areas

4. Turn fireplace off and let cool before

servicing, installing or repairing. Only a

qualied service person should install,

service or repair this replace. Have re-

place inspected annually by a qualied

service person.

5. You must keep control compartments,

burners and circulating air passages

clean. More frequent cleaning may be

needed due to excessive lint and dust

from carpeting, bedding material, etc.

Turn off the gas valve and pilot light before

cleaning replace.

www.fmiproducts.com 56131L6

DIMENSIONS

FRONT VIEW

30"

(Opening)

25"

19 7/8"

(Opening)

RIGHT SIDE

1 7/8"

22 5/8"

41 1/8"

32"

(Opening) 1 7/8"

39 3/4"

26 3/8"

3" 1" 3 1/2"

22 5/8"

34 3/4"

BACK VIEW

TOP VIEW

(Left Side)

(Right Side)

(Front)

(Back)

24"

1115/16

101/2"

11/2"ø 11/2"ø

101/2"

FRONT VIEW

30"

(Opening)

24"

25"

RIGHT SIDE

22 5/8"

43 1/8"

32" (Opening) 1 7/8"

1 7/8"

BACK VIEW

39 3/4"

26 3/8"

3" 1" 2" 3"

22 5/8"

34 3/4"

TOP VIEW

(Left Side)

(Right Side)

(Front)

(Back)

24"

1115/16"

101/2"

ø11/2"ø11/2"

111/8"

Figure 1 - Peninsula Dimensions

Figure 2 - See-Thru Dimensions

www.fmiproducts.com

56131L 7

PRE-INSTALLATION PREPARATION

CLEARANCES

Minimum clearances to combustibles for

replace are as follows:

*Back and sides of surround 0"

Vent Surfaces (side and bottom) 1"

Top Vent Surface (horizontal run) 2"

Ceiling to Opening 36"

Floor 0"

Wall to Front of Glass 36"

Perpendicular Wall to Opening of Unit 2"

Top Spacer 0"

NOTICE: This replace is in-

tended for use as supplemental

heat. Use this replace along

with your primary heating sys-

tem. Do not install this replace

as your primary heat source.

If you have a central heating

system, you may run system’s

circulating blower while using

replace. This will help circulate

the heat throughout the house.

In the event of a power outage,

you can use this replace as a

heat source.

MANTEL CLEARANCES

Figure 3 - Direct-Vent Fireplace

Log Set

Upper

Louver

Panel

Lower

Louver

Panel

Figure 4 - Minimum Clearances

(Peninsula Shown)

CEILING

WALL

36" Min.

0" Floor

LOCATION AND SPACE

REQUIREMENTS

Determine the safest and most efcient loca-

tion for your FMI PRODUCTS, LLC direct-vent

replace. Make sure that rafters and wall

studs are not in the way of the venting system.

Choose a location where heat output is not

affected by drafts, air conditioning ducts, win-

dows or doors. Be aware of all restrictions and

precautions before deciding the exact location

for your replace and termination cap.

When deciding the location of your replace,

follow these rules:

• A projection may be ideal for a new addition

on an existing nished wall. Refer to hori-

zontal termination congurations on page

15 or vertical congurations on page 18.

• Do not connect fireplace venting to a

chimney ue serving a separate solid-fuel

burning replace or appliance.

• Due to high temperatures, do not locate

replace in high trafc areas, windy or drafty

areas or near furniture or draperies.

• Never obstruct front opening of appliance

or ow of combustion and ventilation air.

Keep control compartments accessible.

• Do not locate close to where gasoline or

other ammable liquids may be stored.

Appliance must be kept clear and free from

combustible materials.

www.fmiproducts.com 56131L8

36"

Wall In Front Of Glass

36" Min.

Perpendicular

Wall 2" Min.

From Opening

Right Side

Surround

(0" Min.)

Left Side

Surround

(0" Min.)

TOP VIEW

Figure 6 - Mantel Clearances for

Peninsula and See-Thru Fireplaces

(Peninsula Shown)

21" Min.

15" Min.

12" Min.

Min.

7" Min.

" Max.

UNIT

Spacer

2 x 4

Combustible

Material May

Be Used

Drywall (Gypsum

Board, Sheetrock, etc.)

Safe Zone for

Projection of

Combustible

Material

Woodwork, such as wood trims, mantels and

other combustible materials should not be

placed within 7" of the opening of replace

(see Figure 6).

Combustible material above projecting more

than 1 1/2" from appliance’s front face must

not be placed less than 15" from opening

of appliance, (ref. NFPA Standard 211 Sec.

7-3.3.3)

PRE-INSTALLATION PREPARATION

Continued

Figure 5 - Minimum Clearances

(See-Thru Shown)

Combustible Material Drywall

2 x 4

Stud

Minimum 1" Clearance from

Side (Only for See-Thru)

FRAMING

Once nal location has been determined,

observing clearances for vent termination,

you may construct framing using dimensions

shown in Figures 7 thru 13 depending on your

particular installation

If appliance is to be installed directly on car-

peting, tile (other than ceramic), or any com-

bustible material other than wood ooring, the

appliance must be installed upon a metal or

wood panel extending the full width and depth

of the appliance. There are three holes on

each side of the bottom of unit where screws

can be used to secure unit to oor.

Figure 7 - Rough Opening for Installing

Peninsula Fireplace

" Min.

Min.

Figure 8 - Rough Opening for Installing

Peninsula Fireplace on Platform

* As required by design as long as

ceiling clearance is maintained.

Platform

Must Be

Solid, Flat,

and Fully

Supported

www.fmiproducts.com

56131L 9

PRE-INSTALLATION PREPARATION

Continued

Min.

24"

Figure 9 - Rough Opening for Installing

See-Thru Fireplace

1" Dia. Hole

2" Dia. Hole

Figure 10 - Hole Locations For Gas Line

and Electric Wires for Peninsula and

See-Thru Fireplaces

Height

Depends On

Installation

10"

Square Min.

Figure 12 - Rough Opening for Installing

Exterior Vent Terminal

Vertical

Height

Depends on

Installation

Horizontal

Length Depends

on Installation

Elbow

Figure 13 - Vent Opening Height

Figure 11 - Alternate Gas Supply

Location

The gas supply line may be connected through

side framing or alternately through lower sub-

ooring or a platform base if provided (see

Figures 10 and 11). Depending on installation,

refer to appropriate illustrations.

www.fmiproducts.com 56131L10

GENERAL VENTING

termination is required.

• There must not be any obstruction such

as bushes, garden sheds, fences, decks,

or utility buildings within 24" from the front

of the termination cap.

• Do not locate termination cap where exces-

sive snow or ice build up may occur. Be

sure to clear vent termination area after

snow falls to prevent accidental blockage of

venting system. When using snow blowers,

do not direct snow towards vent termination

area.

VENT TERMINATION CLEARANCES

The nal position of your appliance depends

on the location of the vent termination in rela-

tion to the clearances that must be observed

as shown in Figure 14, page 10.

You may avoid extra framing by positioning

your replace against an already existing

framing member. The back of the replace

may be positioned directly against a com-

bustible wall.

*Check with local codes. In the USA, follow

the current National Fuel Gas Fuel Gas Code,

ANS Z223.1 also known as NFPA 54.

These models are approved for use with FMI

PRODUCTS, LLC 5"-8" Series, rigid type

direct vent pipe as supplied by FMI PROD-

UCTS, LLC or with approved types of exible

vent pipe (not supplied) when appropriate

sized for an 8" outer and 5" inner diameter

application.

Your replace is approved to be vented either

through the side wall, or vertically using the

following guidelines:

• Only use FMI PRODUCTS, LLC supplied

or approved types of venting components

or kits. Do not mix different types of vent

components, modify vent components or

custom fabricate vent components for use

in any one installation.

• Minimum clearance between vent pipes

and combustible materials is 1", except

where stated otherwise.

• Combustible material may be ush with

the top front of replace with a maximum

thickness of 3/4".

• Do not recess venting terminals into a wall

or siding.

• Do not install vent terminals below grade

level. Maintain a minimum height of 12"

above snow line.

• Do not terminate venting system into an

attic or garage.

• If using a venting conguration of only

horizontal venting with no vertical run, a

1/4" rise for every 12" of run toward the

This manual suits for next models

Table of contents

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual